Panasonic EY45A2 Manuel utilisateur
© Panasonic Corporation 2014. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
Order Number PTD1402X36CE
Cordless Multi Purpose Cutter
Model No. EY45A2
Europe
Oceania
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 6
5 Wiring Connection Diagram ---------------------------------15
6 Schematic Diagram ---------------------------------------------15
7 Exploded View and Replacement Parts List -----------16
2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications
NOTE:
Weight indication
Greater than or equal to 1kg:indicated by 0.05kg.
Less than 1kg :indicated by 0.01kg.
NOTE:
This chart may include models that are not available in your area.
Please refer to the latest general catalogue.
For the dealer name and address, please see the included warranty card.
3
3 Troubleshooting Guide
3.1. Troubleshooting Guide
4
5
3.2. Trial Operation (After Checking Troubleshooting Guide)
3.2.1. Assembly
• Confirm if there is no gap between housing A and B by pinching lead wires.
• There is no dust or deformation on battery terminals.
• Confirm all screws are tightened firmly.
• Verify that the cutting blades are not cracked.
• Verify that the hex wrench has been stowed in the storage slot in housing B.
3.2.2. Operation
• Check whether the switch function operate properly.
• Check the smooth movement of lower guard, switch button and off-lock lever.
• Check whether the tool become hot in a short operation.
• Verify that the brake engages when the trigger is released. Repeat this process about 10 times.
3.2.3. Integrity
• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.
• Check for the presence of any dirt or foreign matter from the repair process on the outside of the tool.
6
4 Disassembly and Assembly Instructions
*To assemble the tool, start with 4-10 and proceed to 4-1
4.1. Removing the Blade
4.2. Removing the safety cover B, front cover assembly and transparent
cover
7
4.3. Removing the safety cover and lower guard
8
9
4.4. Removing the base
10
4.5. Removing the housing B
4.6. Removing the interior components
Autres manuels pour EY45A2
1
Table des matières
Autres manuels Panasonic Coupeur
Panasonic
Panasonic EY3550 Manuel utilisateur
Panasonic
Panasonic EY45A2 Manuel utilisateur
Panasonic
Panasonic EY4542XM Manuel utilisateur
Panasonic
Panasonic EY3530NQMKW Manuel utilisateur
Panasonic
Panasonic EY45A2LJ2G Manuel utilisateur
Panasonic
Panasonic EY4542 - CIRCULAR SAW 14.4V Manuel utilisateur
Panasonic
Panasonic EY3552 - 18V METAL SAW Manuel utilisateur
Panasonic
Panasonic EY3502 - CORDLESS METAL SAW Manuel utilisateur
Panasonic
Panasonic EY4542LN2M Manuel utilisateur
Panasonic
Panasonic EY4542 - CIRCULAR SAW 14.4V Manuel utilisateur
