Panasonic AJ-DE97P Manuel utilisateur

Installation Manual

Thank you for purchasing the the unit.

Please read through this manual which tells you:

OHow to set up the unit (assembly precautions)

OHow to check the unit’s functions (methods for checking that the

functions are operating after startup)

Reading through this Manual before proceeding with installation will

make it easier to understand the installation procedures involved.

Non-Linear Editing System

AJ- P

For details on video and audio uploading, editing and other

operations, refer to the Reference Manual (AJ-SF97).

– 2 –

Chapter 1Do these first! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-1. Checking the accessories and attaching the stabilizer feet . . . . . . . . . . 4

1-2. Checking the AC supply voltage and precautions . . . . . . . . . . . . . . . . 6

1-3. Cable connection precautions (rear panel) . . . . . . . . . . . . . . . . . . . . . . 6

1-4. Connecting the peripheral devices and layout precautions . . . . . . . . . 7

Chapter 2Power startup checks and AV disk inspections . . . . . . . . . . . 8

2-1. Checking the power startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2-2. Checking the SCSI device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2-3. AV disk inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3Disk-related configuration checks. . . . . . . . . . . . . . . . . . . . . . . . 13

3-1. Checking the disk settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3-2. Checking the AudioPool, VideoPool & TitlePool directories . . . . . . . . 15

Chapter 4

Checking operation using the pre-installation program

. . . . . 16

4-1. Checking the uploading operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4-2. Check the editing functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4-3. Checking the downloading operation . . . . . . . . . . . . . . . . . . . . . . . . . 30

OWindows and Windows NT are registered trademarks of Microsoft Corporation.

OPentium is a registered trademark of Intel Corporation.

OAdaptec, AHA and SCSISelect are registered trademarks of Adaptec Inc.

All other names of companies and products are the trademarks or registered trademarks of the companies

concerned.

Contents

– 3 –

Appendix

ABIOS screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

A-1. Concerning BIOS information at startup . . . . . . . . . . . . . . . . . . . . . . . 34

A-2. Details on PC unit BIOS information checks . . . . . . . . . . . . . . . . . . . 34

Appendix

BSCSI-BIOS Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

B-1. Outline of SCSI-BIOS Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

B-2. How to start up SCSI-BIOS Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

B-3. How to use SCSI-BIOS Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

B-4. How to exit SCSI-BIOS Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Appendix

CHow to use Disk Administrator provided with

Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C-1.Outline of Disk Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C-2.How to start up Disk Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C-3.Checking the disk settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

C-4.How to inspect the disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

C-5.How to format disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

C-6.How to exit Disk Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Appendix

DHow to use Event Viewer provided with Windows NT . . . . . 53

D-1.Outline of Event Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

D-2.How to start Event Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

D-3.Checking system events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

D-4.How to exit Event Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Contents

Appendix

EShutdown Procedure at Hang-up for Limited Edition

of the Editing Software Program . . . . . . . . . . . . . . . . . . . . . . . . . 55

To improve the operating efficiency, the devices, etc. listed in these operating instructions

are subject to change without prior notice.

– 4 –

This chapter explains the procedures (setup) to prepare the purchased unit for operation and

the cautions to be heeded.

1-1. Checking the accessories and attaching the stabilizer feet . . . . . . . . . . 4

1-2. Checking the AC supply voltage and precautions . . . . . . . . . . . . . . . . 6

1-3. Cable connection precautions (rear panel) . . . . . . . . . . . . . . . . . . . . . . 6

1-4. Connecting the peripheral devices and layout precautions . . . . . . . . . 7

Chapter 1Do these first!

1-1. Checking the accessories and attaching the stabilizer feet

Before proceeding with the connections, check that all the accessories shown

below are present and accounted for.

)Keyboard )Mouse

)Power cord

)Operating

instructions

)Warranty card

)Stabilizers (a4)

)mounting screws (a8)

)Installation manual

(which you are now reading)

)Service support guide

<Check>

Do not subject the supplied mouse, keyboard or cables to strong bumps or shocks. Doing so

could damage them.

)Ferrite cores (a4)

When the SCSI hard disk drive for external expansion

purposes is to be connected, attach one ferrite core to

one end of the SCSI I/F cable and the other one to the

other end.

– 5 –

CAUTION:

To reduce the risk of injury due to tipping over,

Mount the stabilizers before installation.

Attaching the stabilizer feet

Attaching the ferrite cores

When the SCSI hard disk drive for external expansion purposes is to be

connected, one of ferrite cores packed with the unit must be attached to one

end of the SCSI I/F cable and the other one must be attached to the other

end.

It is recommended that the cable shown below be used as the SCSII/F cable.

OModel No. ACK/M-WP made by Adaptec Inc.

– 6 –

1-2. Checking the AC supply voltage and precautions

Use a AC voltmeter or other instrument to check that the supply voltage at

the installation location is inside the following range:

)120 V ±10 %

1-3. Cable connection precautions (rear panel)

Bear in mind the points listed below when connecting the accessory cables to

the unit’s rear panel. It is recommended that you proceed while referring to

the rear panel connection diagram in the Operating Instructions. (Refer to

page 12 of Operating Instructions.)

)Connect the keyboard.

)Connect the mouse.

)Check the names of the connectors on the rear panel to verify that

the keyboard has not been connected to the mouse connector or the

mouse has not been connected to the keyboard connector.

)Connect the power cord to the socket on the main unit.

)Secure the power cord using the clamp.

)Refrain from connecting the power plug to the power outlet at this

stage.

Note:

Not only may the unit fail to operate properly if it has been started up with

a supply voltage outside the above range but the software programs and

data pre-installed on the system hard disk inside the unit may be

destroyed as well.

Use of an uninterruptible power supply system is recommended if the unit

is to be used in unsatisfactory power supply conditions. For details,

consult with your dealer.

<Check>

– 7 –

1-4. Connecting the peripheral devices and layout precautions

Bear in mind the points listed below when connecting the computer monitor,

monitor (Video) for monitoring the pictures and other peripheral devices to

the unit. It is recommended that you proceed while referring to the rear panel

connection diagrams in the Operating Instructions. (Refer to pages 13–16 of

Operating Instructions.)

For details on the handling of peripheral devices, refer to the operating

instructions accompanying each device concerned.

)Connect the peripheral devices while power to the unit and peripheral

devices is off.

)Before moving the unit, turn its power off.

Do not move the unit while the power is still on.

)Install the unit in a flat and stable location.

)At the installation stage, ensure that the connectors and cables

protruding from the unit’s rear panel do not make contact with any

objects in the vicinity.

)At the installation stage, do not drop the keyboard or mouse, and

take care not to run their cables underneath the unit or peripheral

devices.

)Do not place objects on top of the unit.

)Leave a sufficient clearance around the unit in order to improve the

ventilation inside the unit.

)Do not place food or drinks in the vicinity of the unit.

Morsels of food or spilled drinks can cause trouble.

)Check that you have not forgotten to connect the VGA cable between

the unit and the monitor for the computer.

)Check that you have not forgotten to connect the video cable

between the unit and monitor (Video) for monitoring the pictures.

)Check that you have not forgotten to connect the unit and any other

peripheral devices.

)Check that all the devices required have been connected, and insert

the power plugs of the unit and peripheral devices into the power

outlets.

)When the SCSI hard disk drive for external expansion purposes is to

be connected:

Attach one of the ferrite cores packed with the unit to one end of the

SCSI I/F cable and the attach the other one to the other end.

<Check>

– 8 –

This chapter explains the checks that must be conducted on the basic hardware settings and

basic inspections of the AV disks after the unit’s power switch has been set to the ON

position.

When conducting the checks and inspections described in this chapter, do not turn off the

power or reset the system unnecessarily. Doing so may change or destroy the pre-installed

software programs or data.

For details on turning off the power and resetting the system, refer to the

descriptions given for the items concerned.

2-1. Checking the power startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2-2. Checking the SCSI device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2-3. AV disk inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2-1. Checking the power startup

When the unit’s power switch is set to ON, the unit’s basic test is

automatically conducted, and its results can be checked out by beep tones

and displays which appear on the computer monitor.

After the power switches of the computer monitor, monitor (Video) for

monitoring the pictures and other peripheral devices have been set to ON,

set the unit’s power switch to ON and conduct the checks described below at

startup.

If trouble has been detected as a result of conducting the checks, refer to the

“Troubleshooting” section in the Operating Instructions. (Refer to pages

20–27 of the Operating Instructions.)

Since it takes very little time to check the displays on the computer monitor,

you will find it easier to perform the checks if you quickly glance through the

whole of this section and the BIOS screen displays in Appendix A (pages

34–38) and understand what is involved.

For details on how to adjust the monitor and otherwise handle any of the

peripheral devices, refer to the operating instructions accompanying each

device concerned.

Chapter 2Power startup checks and AV disk inspections

Note:

If a monitor display which should have been checked during startup has

been overlooked, the unit must be rebooted so that it can be checked.

Under no circumstances must the power be turned off or the system

reset while white characters appear on a blue background during

startup.

Wait until the Windows NT flag appears, and then reboot the unit using

the system reset switch on the unit’s front panel.

– 9 –

Checking the LEDs on the unit’s front panel

)Check that the two disk access lamps light up and flash when the

power is turned on.

Checking the computer monitor displays (BIOS start screen) during

startup

)Is the memory size value (standard 256 MB) correct?

)Did the CD-ROM drive name appear (for an instant)?

)Did the name of the system hard drive appear?

(Refer to the BIOS screen displays in Appendix A.)

)Did the SCSI card name appear?

(Refer to the BIOS screen displays in Appendix A.)

)Did all the SCSI disk names appear?

(Refer to the BIOS screen displays in Appendix A.)

)Did the PCI device list appear?

(Refer to the BIOS screen displays in Appendix A.)

<Check>

– 10 –

2-2. Checking the SCSI device settings

In this section the SCSI-BIOS Tool is used to check the SCSI device settings.

You will find it easier to perform the checks if, before starting the actual

procedure, you quickly glance through SCSI-BIOS Tool items B-1–B-3

(pages 39–43) in Appendix B and understand how the settings of the parts

corresponding to the items to be checked in this section are displayed.

In particular, the following parts in B-3 must be understood.

(1) SCSI device configuration check

(2) SCSI ID check

If items with different settings have been detected as a result of conducting

the checks, refer to the explanation given in

¬When the SCSI device parameters are wrong¬

which is found in B-3 of Appendix B, and to the “Troubleshooting” section in

the Operating Instructions. (Refer to pages 20–27 of Operating Instructions.)

When the checks in this section have been completed with no errors found,

proceed to the next section [2-3. AV disk inspections] without exiting the

SCSI-BIOS Tool.

1. After the series of checks described in Section 2-1 (Checking the power

startup) have been completed with no errors found, reboot the unit and

check the SCSI device settings.

Note:

If, upon completion of the checks in the previous section, the screen

displays during the startup procedure have reached the white characters

on a blue background status, do not turn off the power or reset the

system until the display status changes.

If either step is to be performed, wait until the Windows flag appears on

the screen, and then reboot the unit using the reset switch.

2. Check the SCSI device settings following the instructions in “(1) SCSI

device configuration check” and “(2) SCSI ID check” in B-3 (pages 40,

41) of Appendix B (SCSI-BIOS Tool).

Autres manuels pour AJ-DE97P

Table des matières

Autres manuels Panasonic Accessoires pour appareils photo

Panasonic

Panasonic AWPH300 - INDOOR PAN/TILT HEAD Manuel utilisateur

Panasonic

Panasonic DMW-MCTZ1 Manuel utilisateur

Panasonic

Panasonic AK-HDC931 Manuel utilisateur

Panasonic

Panasonic WV-7150D Manuel utilisateur

Panasonic

Panasonic DMW-LVF1 Manuel utilisateur

Panasonic

Panasonic AWPH300 - INDOOR PAN/TILT HEAD Manuel utilisateur

Panasonic

Panasonic Varicam AU-VCVF20G Manuel utilisateur

Panasonic

Panasonic Lumix DMW-MCTZ5 Manuel utilisateur

Panasonic

Panasonic HHR370AH Manuel utilisateur

Panasonic

Panasonic AWLK30 - LENS CONTROLLER Manuel utilisateur

Panasonic

Panasonic WV-QDC500S Manuel utilisateur

Panasonic

Panasonic WV7225 - PANA TILT Manuel utilisateur

Panasonic

Panasonic ER-CBN1 Manuel utilisateur

Panasonic

Panasonic WV7220D - CCTV ACCESSORIES Manuel utilisateur

Panasonic

Panasonic DP-100 series Manuel utilisateur

Panasonic

Panasonic BB-HCS301A - Network Camera Server Manuel utilisateur

Panasonic

Panasonic VariCam AU-VREC1G Manuel utilisateur

Panasonic

Panasonic LJ-SK56A Manuel utilisateur

Panasonic

Panasonic Lumix H-HS12035 Manuel utilisateur

Panasonic

Panasonic AS09A51 Mode d’emploi

Panasonic

Panasonic LUMIX DMW-BGS1 Manuel utilisateur

Panasonic

Panasonic DC-GH5M Series Manuel utilisateur

Panasonic

Panasonic Lumix TZ7 Manuel utilisateur

Panasonic

Panasonic AG-CVF10G Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur