Panasonic PV-GS29PL Manuel utilisateur
©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
PV-GS29PL
PV-GS39PL
PV-GS69PL
Colours
(S)...................Silver Type
Digital Video Camcorder
ORDER NO. VM0602008CE
1 Safety Precautions 3
1.1. General Guidelines 3
2 Warning 4
2.1. Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 4
2.2. How to Recycle the Lithium Battery 4
2.3. How to Replace the Lithium Battery 5
3 Service Navigation 6
3.1. Introduction 6
3.2. About Lead Free Solder (PbF) 6
4 Specifications 7
5 Location of Controls and Components 8
6 Service Mode 29
6.1. Error Display 29
6.2. Service Menu 29
7 Service Fixture & Tools 31
7.1. Service Fixture and Tools 31
7.2. Service Position 33
7.3. Removal/Installation of F.P.C. From Non ZIF (Zero
Insertion Force) Connector 35
7.4. Method for Loading/Unloading of Mechanism 36
7.5. EEPROM Data 36
7.6. Replacement Procedures for CSP (Chip Size Package) IC
37
7.7. Special Note 43
8 Disassembly and Assembly Instructions 44
8.1. Cabinet Section 44
8.2. Mechanism Section 67
9 Measurements and Adjustments 71
9.1. Mechanical Adjustment 71
9.2. Electrical Adjustment 73
10 Maintenance 75
10.1. Cleaning Lens, Viewfinder and LCD Panel 75
10.2. How to use the DVC Head Cleaning Tape / VFK1451 75
11 Block Diagrams 77
12 Schematic Diagrams 91
12.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT
NOTES 91
12.2. MAIN SCHEMATIC DIAGRAMS 92
12.3. CAMERA SCHEMATIC DIAGRAM 106
12.4. FRONT SCHEMATIC DIAGRAM 111
12.5. LCD BACKLIGHT SCHEMATIC DIAGRAM (Model: PV-
GS29PL) 112
12.6. LCD BACKLIGHT SCHEMATIC DIAGRAM (Models: PV-
GS39PL/PV-GS69PL) 113
12.7. EVF BACKLIGHT / CASSETTE COVER / BATTERY
CASE SCHEMATIC DIAGRAMS 114
12.8. CCD / REAR / LCD SW SCHEMATIC DIAGRAMS 115
12.9. INTERCONNECTION SCHEMATIC DIAGRAM 116
12.10. VOLTAGE CHART 117
13 Printed Circuit Board 123
13.1. MAIN P.C.B. 123
13.2. CAMERA P.C.B. 126
13.3. FRONT P.C.B. 128
13.4. LCD BACKLIGHT P.C.B. (Model: PV-GS29PL) 129
13.5. LCD BACKLIGHT P.C.B. (Models: PV-GS39PL/PV-
GS69PL) 130
14 Appendix Information of Schematic Diagram 131
14.1. CHECKING POINT TABLE OF THE CSP IC 131
14.2. WAVEFORM TABLE 138
15 Exploded Views 141
15.1. MAIN PARTS SECTION 141
15.2. FRONT AND BOTTOM CASE SECTION 142
15.3. SIDE CASE R AND LCD SECTION 143
15.4. CCD AND LENS SECTION 145
15.5. EVF SECTION 146
15.6. MECHANISM SECTION 147
15.7. PACKING PARTS AND ACCESSORIES SECTION 148
16 Replacement Parts Lists 149
16.1. MECHANICAL REPLACEMENT PARTS LIST 149
16.2. ELECTRICAL REPLACEMENT PARTS LIST 151
CONTENTS
Page Page
2
PV-GS29PL / PV-GS39PL / PV-GS69PL
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essential
that these critical parts should be replaced with
manufacturer’s specified parts to prevent shock, fire, or
other hazards. Do not modify the original design without
permission of manufacturer.
2. An Isolation Transformer should always be used during the
servicing of AC Adaptor whose chassis is not isolated from
the AC power line. Use a transformer of adequate power
rating as this protects the technician from accidents
resulting in personal injury from electrical shocks. It will also
protect AC Adaptor from being damaged by accidental
shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been
overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices such
as insulation barriers, insulation papers shields are properly
installed.
5. After servicing, make the following leakage current checks
to prevent the customer from being exposed to shock
hazards.
3
PV-GS29PL / PV-GS39PL / PV-GS69PL
2 Warning
2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
2.2. How to Recycle the Lithium Battery
4
PV-GS29PL / PV-GS39PL / PV-GS69PL
2.3. How to Replace the Lithium Battery
The lithium battery (ML-621S/F9D) is not supplied as a service part and must be replaced as part of the Cassette Cover Unit. (Refer
to “Disassembly and Assembly Instructions.")
NOTE:
This Lithium battery is a critical component. (Type No.: ML-621S/F9D Manufactured by Panasonic.) (Not supplied)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
5
PV-GS29PL / PV-GS39PL / PV-GS69PL
3 Service Navigation
3.1. Introduction
This service manual contains technical information which will allow service personnel´s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
Note 1:
AC Adaptor used on these movie camera is PV-DAC14D. However, DE-974FA is supplied as a replacement part for PV-
DAC14D. This AC Adaptor is supplied only as a unit.
3.2. About Lead Free Solder (PbF)
6
PV-GS29PL / PV-GS39PL / PV-GS69PL
4 Specifications
7
PV-GS29PL / PV-GS39PL / PV-GS69PL
5 Location of Controls and Components
8
PV-GS29PL / PV-GS39PL / PV-GS69PL
9
PV-GS29PL / PV-GS39PL / PV-GS69PL
10
PV-GS29PL / PV-GS39PL / PV-GS69PL
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Panasonic caméscope
Panasonic
Panasonic HDC-TM15K Manuel utilisateur
Panasonic
Panasonic PV-GS65PP Manuel utilisateur
Panasonic
Panasonic HC-V385GC Manuel utilisateur
Panasonic
Panasonic AG-AC160PJ Manuel utilisateur
Panasonic
Panasonic NV-GS70B Manuel utilisateur
Panasonic
Panasonic PV-GS16 - Mini Dv Digital Video Camcorder Manuel utilisateur
Panasonic
Panasonic OmniMovie PV-S445 Manuel utilisateur
Panasonic
Panasonic HDC-SD80 Caractéristiques techniques
Panasonic
Panasonic Palmcorder PV-DV92 Manuel utilisateur
Panasonic
Panasonic NV-VX21B Manuel utilisateur
Panasonic
Panasonic HDC-SD60EF Manuel utilisateur
Panasonic
Panasonic Palmcorder PV-L561 Manuel utilisateur
Panasonic
Panasonic AG-DP800HP Manuel utilisateur
Panasonic
Panasonic HC-MDH2GC Manuel utilisateur
Panasonic
Panasonic AJD210P - DIGITAL CAMERA RECORDER Manuel utilisateur
Panasonic
Panasonic AG-HPX370 Manuel utilisateur
Panasonic
Panasonic AG-DVX100A - Pro 3-CCD MiniDV Proline... Manuel utilisateur
Panasonic
Panasonic HDC-HS900 Manuel utilisateur
Panasonic
Panasonic Palmcorder IQ PV-L606 Manuel utilisateur
Panasonic
Panasonic NV-DS35EG Manuel utilisateur
