Panasonic PM-25 Series Manuel utilisateur

2021.12 panasonic.net/id/pidsx/global

U-shaped Micro-photosensor

PM-□25 / PM-□45 series

When Using for Safety Applications

WUME-PMSAFETY-1

WUME-PMSAFETY-12

(MEMO)

WUME-PMSAFETY-1 3

Thank you for purchasing a PM-□25 / PM-□45 series U-shaped Micro photosensor with built-in

amp.

Read this document carefully and thoroughly for the correct and optimum use of this product.

Keep this document in a convenient place for quick reference.

This document contains “When Using for Safety Applications” related to the PM-□25 / PM-□45

series when used as part of a safety system. Before using this device, be sure to read this doc-

ument in addition to the documentation included with other devices used in the safety system.

This document is for the following persons who have received appropriate training and have

knowledge of safety and photoelectric safety sensors.

● Those who are in charge of introduction of this device.

● Those who incorporate this device into systems or design them.

● Those who install and / or connect this device.

● Those who manage or perform operations at sites where this device is used.

Notes

1) No part of this document should be copied or reprinted in any form or by any means without

prior permission in writing from the publisher.

2) The contents of this document are subject to change without notice for future improvement.

3) Every e󰀨ort is made to produce this document. If you nd any question, error, incorrect col-

lating and / or missing page, please do not hesitate to contact our nearest local o󰀩ce to you:

Panasonic Industrial Devices SUNX.

4) This document (Japanese and English) is an original publication.

WUME-PMSAFETY-14

Contents

Chapter 1 Introduction ···································································· 1-5

1.1 Safety Precautions Always observe ··············································· 1-6

1.2 Handling Precautions································································· 1-6

Chapter 2 Standards and Regulations················································ 2-1

2.1 Standards and Regulatory Compliance·········································· 2-2

2.2 Safety Functions ······································································· 2-2

2.3 Parameters related to safety (Parameters described in ISO13849-1) ··· 2-2

2.4 Cautions when using in a ISO13849-1 Category 3 PLd system··········· 2-4

Chapter 3 Maintenance··································································· 3-1

3.1 Daily Inspection ········································································ 3-2

3.2 Regular (Bi-annual) Inspection····················································· 3-2

3.3 Inspection upon product replacement / installation ··························· 3-2

Chapter 4 Troubleshooting ······························································ 4-1

4.1 Troubleshooting ········································································ 4-2

1-5

1.1 Safety Precautions Always observe ··············································· 1-6

1.2 Handling Precautions································································· 1-6

Chapter 1 Introduction

WUME-PMSAFETY-11-6

1.1 Safety Precautions Always observe

The PM-□25 / PM-□45 conforms to the international standard ISO 13849-1 (Category 1, PLc)

and can be used as a detection device to indirectly protect the human body.

This manual explains important rules that must be observed to prevent personal injury and prop-

erty damage.

■The hazards that may occur if the product is used incorrectly are described and clas-

sied by level of harm.

WARNING Risk of death or serious injury.

WARNING

●Do not use this product for an application where it directly detects the human body. Otherwise,

there is a risk of death or serious injury.

●When the human body needs to be detected for safety application, use products that conform to the

laws and standards related to human body detection for safety application in each country, such as

OSHA, ANSI, and IEC.

1.2 Handling Precautions

■In this manual, the following symbols are used to indicate safety information that must

be observed.

Indicates an action that must be taken.

Specications

●Before using this device, be sure to conrm the standards / regulations applied in the rele-

vant nation and region.

●Since parts or all of a human body may not be detected, use this product solely for indirect

protection methods only.

●Objects within the deadband region or outside of the detection area, and transparent objects

cannot be detected.

Usage environment

●Since the sensor is intended for use inside machines, no special countermeasures have

been taken against extraneous light. Please take care that extraneous light is not directly in-

cident on the beam receiving section.

Power supply

● Be sure to use a SELV (Safety Extra Low Voltage) power supply unit with this device.

Wiring

●All electrical wiring should conform to the regional electrical regulations and laws. The wiring

should be done by engineer(s) having the special electrical knowledge.

●Power supply and output wires for connecting to this device should be 0.3 mm2or greater

with a total length of less than 30 m.

WUME-PMSAFETY-1 1-7

●Cables that are 0.3 mm2or greater can be used for a length of up to 30 m, but since voltage

will drop as the cable gets longer, ensure that the power supply voltage at the end of the sen-

sor's included cable and at the terminal is within the rating.

Overall length: 100 m

Extension cable

Supply voltage:

4.5 V or more

5 to 24 V DC

±10%

Output

0 V

●If there is a large surge generating equipment, such as, motor, solenoid, electromagnetic

valve, etc., in the vicinity of the micro-photosensor, use a surge absorber on that equipment.

Further, do not run the sensor cables along power lines and use a capacitor between +V and

0 V. Use the sensor after conrming that the surge has been eliminated.

● Do not use during the initial transient time (50 ms) after the power supply is switched on.

Operation

● In case this device does not perform properly, the operator should report this to the person in

charge and stop the machine operation immediately. The machine must not be operated until

correct performance of this device has been conrmed.

Maintenance and Inspection

● If the sensor is used in a place having excessive dust, periodically clean the emitting and re-

ceiving sections with a dry, soft cloth.

Other precautions

● This product has been developed / produced for industrial use only. This product must be dis-

posed of using environmentally-friendly methods in accordance with applicable disposal and

processing regulations of the country it is used in.

WUME-PMSAFETY-11-8

(MEMO)

2-1

Chapter 2 Standards and

Regulations

2.1 Standards and Regulatory Compliance·········································· 2-2

2.2 Safety Functions ······································································· 2-2

2.3 Parameters related to safety (Parameters described in ISO13849-1) ··· 2-2

2.4 Cautions when using in a ISO13849-1 Category 3 PLd system··········· 2-4

WUME-PMSAFETY-12-2

2.1 Standards and Regulatory Compliance

This product complies with the following standards and regulations.

EMC Directive 2014/30/EU

EN 60947-5-2

ISO 13849-1: 2015(Category 1, PLc)

2.2 Safety Functions

This product has semiconductor output. Conrm the following before use.

■During detection (When using Dark-ON) : OUT1/OFF & OUT2/ON

■During non-detection (When using Light-ON) : OUT1/ON & OUT2/OFF

2.3 Parameters related to safety (Parameters described in ISO13849-1)

■Safety side: During detection (When using Dark-ON)

Name NPN output type PNP output type

OUT1 OUT2 OUT1 OUT2

Safety side: Output status OFF ON OFF ON

MTTFd 100 years

DCavg 0

CCF 75

T1 (Proof Test Interval) 20 years

Operating altitude 2,000 m or lower

Response time

Under light received condition: 20 μs or less

Under light interrupted condition: 80 μs or less

(Maximum response frequency: 3 kHz) (Note 1)

Ambient temperature

(Note 2,3)

–25 to +55 °C (No dew condensation or icing allowed),

Storage: –30 to +80 °C

■Safety side: During non-detection (When using Light-ON)

Name NPN output type PNP output type

OUT1 OUT2 OUT1 OUT2

Safety side: Output status ON OFF ON OFF

MTTFd 100 years

DCavg 0

CCF 75

T1 (Proof Test Interval) 20 years

Operating altitude 2,000 m or lower

Response time

Under light received condition: 20 μs or less

Under light interrupted condition: 80 μs or less

(Maximum response frequency: 3 kHz) (Note 1)

Ambient temperature

(Note 2,3)

–25 to +55 °C (No dew condensation or icing allowed),

Storage: –30 to +80 °C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Accessoires

Panasonic

Panasonic MA3J700 Manuel utilisateur

Panasonic

Panasonic CZ-CSRC2 Manuel utilisateur

Panasonic

Panasonic MA3J702 Manuel utilisateur

Panasonic

Panasonic MA3S132D Manuel utilisateur

Panasonic

Panasonic MA2J7280G Manuel utilisateur

Panasonic

Panasonic WV-PB5508 Manuel utilisateur

Panasonic

Panasonic KX-HNA101 Manuel utilisateur

Panasonic

Panasonic PE Series Manuel utilisateur

Panasonic

Panasonic MA4ZD14 Manuel utilisateur

Panasonic

Panasonic TY-TPEN2 Manuel utilisateur

Panasonic

Panasonic MA3Z7920G Manuel utilisateur

Panasonic

Panasonic MA3X704D Manuel utilisateur

Panasonic

Panasonic MA22F20 Manuel utilisateur

Panasonic

Panasonic WRT 3367-8 Manuel utilisateur

Panasonic

Panasonic D-IMager EKL3104 Manuel utilisateur

Panasonic

Panasonic KX-TGP600 Manuel utilisateur

Panasonic

Panasonic WJ-PB85A32 Manuel utilisateur

Panasonic

Panasonic GP-X SERIES Manuel utilisateur

Panasonic

Panasonic HL-C2 Series Manuel utilisateur

Panasonic

Panasonic MAZTxxxH Series Manuel utilisateur

Panasonic

Panasonic MA3SE02 Manuel utilisateur

Panasonic

Panasonic WV-TW370 Manuel d'utilisation

Panasonic

Panasonic HL-G1-A-C5 Series Manuel utilisateur

Panasonic

Panasonic DP-0 Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur