Panasonic EX-Z Series Manuel utilisateur

Ultra-minute Photoelectric Sensor

EX-Z Series

USER’S MANUAL

WUME-EXZ-1

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Contens

1. Cautions··························································································3

2. Part Description ················································································4

3. Mounting ·························································································5

3-1 Mounting of sensor················································································· 5

3-2 Installation interval ················································································· 7

4. I/O Circuit Diagram············································································9

5. Stability Indicator·············································································10

6. Beam Alignment·············································································· 11

7. Option···························································································12

7-1 Sensor mounting bracket········································································12

8. Specications ·················································································13

8-1 Side sensing type ·················································································13

8-2 Front sensing type ················································································14

9. Dimensions····················································································15

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

1. Cautions

WARNING

●Never use this product as a sensing device for personnel protection.

●When using sensing devices for personnel protection, use products that meet laws

and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in

each region or country.

●This product has been developed / produced for industrial use only.

●This product employs a small cable of 0.1mm2in conductor area. Take care that the

cable is not pulled with a strong force, as it may damage this product or break its wires.

●Make sure that stress by forcible bend or pulling is not applied to the sensor cable joint.

●

Cable can be extended up to 50m in total length (each emitter / receiver of thru-beam

type) if extension cable is more than 0.3mm2in electric conductor cross-sectional area.

●Make sure that the power supply is OFF while adding or removing the controllers.

●Take note that incorrect wiring will damage the sensor.

●Verify that the supply voltage variation is within the rating.

●If power is supplied from a commercial switching regulator, ensure that the frame ground

(F.G.) terminal of the power supply is connected to an actual ground.

●When noise generating equipment (switching regulator, inverter motor, etc.) is used in

the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to

an actual ground.

●Do not run the wires together with high-voltage lines or power lines or put them in the

same raceway. This can cause malfunction due to induction.

● Take care that the sensor is not directly exposed to uorescent lamp from a rapid-starter

lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing per-

formance.

●Do not use during the initial transient time (50ms) after the power supply is switched

ON.

●This product is suitable for indoor use only.

●Avoid dust, dirt, and steam.

●Do not use this sensor in places where it may come in contact with corrosive gas, etc.

●Ensure that the product does not come into contact with organic solvents such as thin-

ner.

●Ensure that the product does not come into contact with strong acid or alkaline.

●Ensure that the product does not come into contact with oil or grease.

●This product cannot be used in an environment containing inflammable or explosive

gases.

●Never disassemble or modify the product.

●Cable end has not been waterproofed. Do not use the product in any manner that may

cause water entry via cable end.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

2. Part Description

Thru-beam emitter side sensing type EX-Z11□, EX-Z12□, EX-Z13□

Beam emitting part

Thru-beam receiver side sensing type EX-Z11□, EX-Z12□, EX-Z13□

Operation indicator (Orange)

Lights up when the sensing output

is ON.

Beam receiving part

Stability indicator (Green)

Lights up under the stable light condition

or the stable dark condition

Thru-beam emitter front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□

Beam emitting part

Thru-beam receiver front sensing type EX-Z11F□, EX-Z12F□, EX-Z13F□

Operation indicator (Orange)

Lights up when the sensing

output is ON.

Beam receiving part

Stability indicator (Green)

Lights up under the stable light condition

or the stable dark condition

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

3. Mounting

3-1 Mounting of sensor

●The tightening torque should be 0.2N·m or less.

● M2 screw and nut, spring washer, and at washer are accessory of this product.

When tapping in mounting section (Unit: mm)

Sensing

direction

8.5

M2 screw (length 10)

(accessory)

M2×0.4

Tapping depth: 5

Sensing

direction 8.5

M2 screw (length 6)

(accessory)

M2×0.4

Tapping depth: 7

When using screws and nuts that are accessory of the product (Unit: mm)

Sensing

direction

8.5

M2 screw (length 10)

(accessory) Thickness of mounting

plate: 2 or less

Nut

Spring washer

Flat washer

Thickness of mounting

plate: 2 or less

Nut

Spring washer

Flat washer

Sensing

direction 8.5

M2 screw (length 6)

(accessory)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

When using sensor mounting bracket (optional)

L-shaped mounting bracket

MS-EXZ-1 Mounting bracket for front sensing type

MS-EXZ-2

Mounting spacer for front sensing type

MS-EXZ-4

Mounting bracket for side sensing type

MS-EXZ-3

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

3-2 Installation interval

●Interference prevention function is not incorporated in this product. In case mounting two

sets of this product close together, please mount it as drawing below indicates. (Typical

example)

● Find out the operating point ℓ1 on the parallel deviation diagram for the sensing distance

L1. Separate sensors by 2 X ℓ1 or more.

EX-Z11□, EX-Z11F□

010 1020 20

Operation distance ℓ(mm)

CenterLeft Right

(L1)

(ℓ1)

Sensing distance L (mm)

In case using at sensing distance (L1) 50mm, the

operation point (ℓ1) is approx. 8.02mm according

to diagram above.

The installation interval is

Approx. 8.02mm X 2 = approx. 16.04mm

Thus, install the product to approx. 16.04mm or

more away.

50mm

16.04mm

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

EX-Z12□, EX-Z12F□

200

100

050 50100 100

Operation distance ℓ(mm)

CenterLeft Right

(L2)

(ℓ2)

Sensing distance L (mm)

In case using at sensing distance (L2) 200mm, the

operation point (ℓ2) is approx. 30.5mm according

to the diagram at left.

The installation interval is

Approx. 30.5mm X 2 = approx. 61mm

Thus, install the product to approx. 61mm or more

away.

200mm

61mm

EX-Z13□, EX-Z13F□

800

400

600

200

050 50100 100

Operation distance ℓ(mm)

CenterLeft Right

(L3)

(ℓ3)

Sensing distance L (mm)

In case using at sensing distance (L3) 500mm, the

operation point (ℓ3) is approx. 81.9mm according

to the diagram at left.

The installation interval is

Approx. 81.9mm X 2 = approx. 163.8mm

Thus, install the product to approx. 163.8mm or

more away.

500mm

163.8mm

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

4. I/O Circuit Diagram

NPN output type and PNP output type common: Thru-beam type emitter EX-Z1□

Main circuit

(Brown) + V

(Blue) 0V

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

NPN output type: Thru-beam type receiver EX-Z1□

Main circuit

(Brown) + V

(Black) Output

(Blue) 0V

Load

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

PNP output type: Thru-beam type receiver EX-Z1□-P

Main circuit

(Brown) + V

(Black) Output

(Blue) 0V

Load

‒

12 to 24V DC

±10%

Users’ circuitInternal circuit

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

5. Stability Indicator

●The stability indicator (green) lights up when the incident light intensity has sufficient

margin to the operation level.

When the beam is received at a level where the stability indicator lights up, stable sens-

ing is possible in both the "Light" state operation and the "Dark" state operation without

being affected by changes in temperature, voltage, etc.

Approx.

15%

Approx.

25%

100

Lights up

Turned off

"Light" state operation

"Dark" state operation

Lights up

Output operation level

Light margin width

Dark margin width

Output operation

Stability indicator operation

Sensing distance

Incident light intensity (%)

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Table des matières

Autres manuels Panasonic Accessoires

Panasonic

Panasonic MIR-H163-PA Manuel utilisateur

Panasonic

Panasonic Infrared Light Emitting Diodes LN77L Manuel utilisateur

Panasonic

Panasonic MA2J7270G Manuel utilisateur

Panasonic

Panasonic LX-111 Series Manuel utilisateur

Panasonic

Panasonic MA6X124 (MA124) Manuel utilisateur

Panasonic

Panasonic KX-TDA0155CE Manuel utilisateur

Panasonic

Panasonic EKL3106 Manuel utilisateur

Panasonic

Panasonic MA26P02 Manuel utilisateur

Panasonic

Panasonic MA2J7280G Manuel utilisateur

Panasonic

Panasonic MA2J7040G Manuel utilisateur

Panasonic

Panasonic MALM062HG Manuel utilisateur

Panasonic

Panasonic MA4Z159 Manuel utilisateur

Panasonic

Panasonic MCO-170AICUVH Series Manuel utilisateur

Panasonic

Panasonic MA2J112 (MA112) Manuel utilisateur

Panasonic

Panasonic Multi Chip Discrete UP05C8B Manuel utilisateur

Panasonic

Panasonic HG-F1 Series Manuel utilisateur

Panasonic

Panasonic MA4Z7130G Manuel utilisateur

Panasonic

Panasonic MA2J729 (MA729) Manuel utilisateur

Panasonic

Panasonic MA4X159A Manuel utilisateur

Panasonic

Panasonic MA27P01 Manuel utilisateur

Panasonic

Panasonic Light Emitting Diodes LN217RPH Manuel utilisateur

Panasonic

Panasonic MA4S111 Manuel utilisateur

Panasonic

Panasonic KX-HNS104 Manuel utilisateur

Panasonic

Panasonic EE23 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur