Panacom BL-1353HS Manuel utilisateur
Pg. 3
BL-1353HS - USER MANUAL
Thanks for purchasing PANACOM BL-1353HS. Please read this manual carefully
before using the headset, which is the best guideline offering best service.
GETTING STARTED
Please read this user ‘s manual carefully before using the product to make
a correct use of all functions and know well about the system connection
and usage.
Please keep this manual in a safe place for future reference.
INTRODUCTION
This Bluetooth® headphone will allow you to listen to your music wirelessly
from your mobile phone, tablet or other Bluetooth® enabled device. It
delivers powerful and clear sound. The built-in microphone will allow you to
answer calls from mobile phone.
WARNING
Prolonged use of headphones at high volume may cause irreparable hearing
loss. We strongly advise you to adjust your listening volume to a reasonable
level. The higher the volume, the more you risk damaging your hearing
quickly.
We also recommend you to use your headphones responsibly! It is dangerous
or even illegal in some areas, to use headphones in situations that require
your full attention, such as driving a car, motorcycle or bicycle, but also as a
pedestrian when crossing the street, etc..
Pg. 4
PRECAUTIONS
Please refer to this Users’ Manual before use to use it properly. The contents
stated herein may be modied from time to time for better service as the
product properties and functions are changed without prior notice For the
sound performances of the product, never use it in too cold, too hot, too
dusty or humid places, especially:
1. Moist or underwater conditions
2. Near the heater or hi-temperature services
3. Solarization
4. Places apt to fall
5. Never disassemble the combination audio; otherwise, it may invalidate
the warranty.
Pg. 5
KEY DESCRIPTION
1. Foldable and adjustable headband
2. Multi-function button (MFB) : Power on/power off/answer a
call/end a call/reject a call/redial last number/pause/play
3. “</V-” button: Short press for Previous Track; Long press to
decrease Volume
4. “>/V+” button: Short press for Next track; Long press to
increase Volume
5. LED indicator (see below for function details)
6. Built-in microphone
7. 3.5mm Aux-in jack
8. Micro USB Charging port
Pg. 6
FONCTION OF LED INDICATOR
A. When charging
RED LED is on when the battery is charging. RED LED is off when
battery charge is nished.
B. When using the headphone
RED and BLUE LED blink alternately when the headphone is in
pairing mode. BLUE LED bright when there is no phone conver-
sation.
RED LED gradually turns on and off every 5 second during phone
conversation. “No battery” sound alert when the battery has low
power.
CHARGING THE BATTERY
The headset comes with a built in rechargeable battery. Before
using it for the rst time we recommend you charge the battery
fully. Only use the supplied USB Cord to charge the headset.
Please charge for 4 hours.
Connect the micro USB connector of the charging cable into
the micro USB port on the side of the headphone. Connect the
other end of the USB cable to your computer’s USB port or to an
optional USB wall charger (not included)
The RED LED indicator light is illuminated.
The RED LED indicator light shuts off when the speaker is fully
charged. (Approximately 4 hours).
Pg. 7
OPERATION INSTRUCTIONS
SWITCHING ON/OFF
Switch ON : Press and hold the MFB for 5 seconds, until the LED
ashes BLUE and you can heard “waiting for a connection” from
headphone.
Switch OFF: Press and hold the MFB for 3-5 seconds , until the
LED stops ashing and you can heard “power off” from head-
phone.
PAIRING INSTRUCTIONS
You need to pair the headphone with your Bluetooth® enabled
device (smartphone, tablet, mp3 player, computer, etc.) before
enjoying the music wirelessly with the headphone.
Enter in pairing mode
Be sure that the headphone is in power off status rst, press
and hold the MFB for 3-5 seconds, until red and blue led blink
alternately and heard “waiting for a connection” from headphone.
Then release the MFB button, the unit is now in paring mode.
Pairing the headphone with Bluetooth® devices
Make the headphone enter into pairing mode (please refer to
above section)
After searched, select “BL-1353HS” in the device list on the
Bluetooth® device.
Pg. 8
If a password is asked, enter the “0000” and press “connect”
(only some Bluetoothiv devices will ask for a password)
When the connection is successful, “connected” will be heard
and the BLUE LED is illuminated while paired.
Please note pairing mode on the headphone will last for around
3 minutes. If no devices are paired within around 5 minutes the
headphone will automatically turn off and can heard “power off”
. If pairing is unsuccessful, turn off the headphone rst and then
re-pair again following the above steps.
Re-connecting to Bluetooth® devices
Every time the headphone is switched on, it will connect to the
nearest and the last connected device automatically .
LISTEN TO MUSIC
When the headphone is correctly paired with your Bluetooth®
device, simply start to play music on your device and you can
enjoy the sound wirelessly in your headphone.
Volume up in music mode: Long press on volume “+” key. You will
hear a beep tone when the maximum volume level is reached.
Volume down in music mode: Long press on volume “-” key. You
will hear a beep tone when the minimum volume level is reached.
Go to next song of your playlist: Short press on the Next « + »
key.
Pg. 9
Go to previous song of your playlist: Short press on the Prey « +
» key.
Play/Pause music: Short press on the MFB to pause the music.
Short press again to play again.
HANDS-FREE FUNCTION
You can answer calls from your mobile phone when the head-
phone is paired with your mobile phone. If you receive a call when
listening to music, your music will pause automatically and you
will hear your telephone ring tone in the headphone.
Answer a call: Short press the multifunction button.
Reject a call: Press and hold the MFB button for 3 seconds until
an indication tone is heard. End a call: Short press the multifunc-
tion button.
Volume up in conversation mode: Long press on volume “+” key.
when the volume has reached the maximum level, you will hear
an indication tone.
Volume down in conversation mode: Long press on volume “-”
key, when the volume has reached the minimum level, you will
hear an indication tone.
Redial the last number : when connected to a device in standby
mode, short press the MFB button twice.
Pg. 10
AUX FUNCTION
You can use the 3.5mm cabled included in the kit to play music
once your Bluetooth is turned off or once the battery of the
device is out of power. Connect one end of the 3.5 mm aux cable
into the Aux jack of the headset. The other end of the cable con-
nects to the 3.5 mm jack of your mobile phone / computer / audio
devices.
(Note: Bluetooth mode should be turned of while using the AUX
feature. Don’t connect Bluetooth between your headset and your
mobile phone when Aux is being used)
MOBILE DEVICES SUPPORTED
In theory, it can support all equipments with Bluetooth®-enabled
phone or music device that supports Advanced Audio Distribution
Prole (A2DP) and Audio Video Remote Control Prole (AVRCP).
In order for Bluetooth® devices to communicate with one
another properly, they must utilize the same Bluetooth® prole.
To determine the proles supported by your device, please refer
to the device’s user guide. Certain Bluetooth features including
those listed may not be supported by all compatible Bluetooth®-
enabled devices, and/or the functionality of such features may be
limited in certain devices.
Table des matières
Langues :
Autres manuels Panacom casque
