Pacific Image Electronics CyberView PF 135+ Manuel utilisateur
PowerFilm
CyberView
User’s
Plus Scanner
PF 135+
Manual
*CyberView PF135 Plus software is the scanning software for the PowerFilm
Plus Scanner 1
FCC
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This Equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected to.
• Consult the dealer or an experienced radio/TV technician for help.
Warning:
Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned that
changes or modifications not expressly approved by the party responsible for compliance could VOID
your authority to operate the equipment
2
Table of Contents
TABLE OF
CONTENTS
Unpacking your scanner 4
Installing Software -includes the hardware driver 6
Installing Hardware 7
Sorting & Cleaning Film strips 8
Loading Filmstrips 10
How to Scan 11
Configure Settings 12
Main User Interface 13
Scan Settings defined 14
Scan Settings - Scanning 15
Tips & Troubleshooting
Reference video links 16
Technical Support Contact information 18
3
Unpacking your Scanner
Unpacking your Scanner
Check the package content before getting started. For Quick Installation please refer to Quick Installation Guide.
Important! Save the original box, receipt and packing material should they be needed for future shipping needs.
Package Contents
•Film Scanner / Film feeder
•Universal Power Adapter w/interchangeable plug(US/EU/UK)
•USB 2.0 Cable
•Quick Reference User Guide & User Manual
Warning!
Using any other power adapter can severely damage the scanner and will VOID the product
warranty.
GENERAL GUIDANCE:
• Only use the supplied USB-Cable. Connect the computer to the scanner directly using the USB 2.0 cable.
• Do not use a Hub or extension cable. Only use the USB ports on the rear of desktop computers is supported
• If there are any other devices (multifunction device, printers, scanners, webcam) connected to the computer via
USB make sure they are powered off.
• A minimum of 4 GB RAM (Windows/Mac) and 30GB Hard drive space minimum is required. 6GB RAM or more
highly recommended.
Assembling the unit, once unpackaged, and all
the shipping tape is removed, insert the film feed
guide into the unit
4
Operating Temperature info
Operating Ambient Temperature Range
50ºto 104ºF (10ºto 40ºC)
Note: Do not turn on the scanner unless it is within this range. If the scanner has been
stored or transported outside of this range, allow it to return to within this range before
turning it on. OperatingAmbient Humidity Range 15% to 76% relative humidity (non-
condensing): Do not turn on the scanner unless it is within this range. If the scanner has
been stored or transported outside of this range, allow it to return to within this range
before turning it on. OperatingAmbient Humidity Range 15% to 76% relative humidity
(non-condensing)
Note: If the scanner is stored or to be transported in cold temperature and then brought
into a warm / humid environment condensation may occur.
WARRANTY INFORMATION NOTICE
Pacific Image warrants this product to be free from defects of material and workmanship
for 1 year from the ORIGINAL date of purchase.
5
Installing Software
Installing Software
Be sure to install the Software Application BEFORE connecting the scanner
Download the appropriate software using this online link Download Drivers
Installing Software - PC Users if you are unsure please verify if your system is 32 or 64 bit here:
Control Panel\System and Security\System
Download the software using the link provided above, selecting the correct version
a. Once downloaded you need to run the installer to install the software on your system
PC: Open the Downloads folder locate the installer file PowerFilm_Windows…. Double click the installer to begin
Installing, you may encounter a warning Windows protected your PC Select “More info…” and choose Run Anyway
Mac: Open downloads locate the installer file PowerFilm_Mac xxx.. New security protocols require these steps to
allow the software installation. Mac OS 10.7-10.12 - Hold down the "Control" key on the keyboard and click on the
software installer package, then click on "Open" then you will see an unidentified developer warning message select
"Open" to begin the installation process Mac OS 10.13 - Hold down the "Control" key on the keyboard and double
click on the software installer, then you will see an unidentified developer warning message, select "Open" to begin
the installation
6
Installing the Hardware
a. Once the software has been successfully installed and the system rebooted, if required you are ready to
connect the scanner, Locate the power switch on the back of the device and make sure it is in the OFF
position (circle in) before connecting
b. Assemble the power adapters 2 pieces together if you have not done so already, by sliding the plug
connector into the slot on the adapter until it clicks into position.
c. Connect theAC adapter to the back of the scanner and connect the adapter to a suitable power outlet
d. Connect the USB cable to the back of the scanner then to the appropriate port on the computer (no hubs,
front ports)
Please Note: When installing your new scanner onto a Windows system that already has another USB
connected Flatbed scanner or All-in-one Scan/Copier/Printer device connected via USB , be sure to power
them off to avoid hardware conflicts, this does not apply to Wi-Fi connected device, If you will be using a
Desktop computer, please connect only to the rear USB ports, do not use any type of USB extension cable
or hub to connect the scanner, data transfer is hindered when doing so causing the software to not respond,
or not communicate at all.
a. When considering scanner placement be sure to leave sufficient room in front of the unit for the film to
come out, otherwise your strips could end up on the floor.
b. Power on the scanner
FIRST TIME USE: Give this a couple of minutes for your computer to connect the scanning device to the
correct hardware drivers installed previously
g. Open the scanning software PowerFilm software from the desktop icon, or (MAC) underApple menu –
Go –Applications PowerFilm
Installing Hardware Installing Hardware
7
Sorting & Cleaning Filmstrips
The scanner is capable of scanning color positive, color negative and black & white 35mm filmstrips, you will
want to sort these by type into their respective groups before beginning to scan, EXAMPLE: Color positives
together, color negatives together and so on, the scanner can hold up to 10 filmstrips at a time, in sizes ranging
from 2 frames up to 6 frames, this unit does not scan rolls of film
This scanner does not support scanning any other sized filmstrips. (i.e. 110, 126 or APS are not supported),
Note: Strips must be in good condition, If filmstrips have any jagged or gnarled edges please trim them so that
they are smooth before inserting into the scanner. No curled strips, and no tape.
Sorting & Cleaning Filmstrips
8
Sorting & Cleaning Filmstrips continued
If the films have dust on them, clean them before inserting into the scanner, using a 98% or higher rubbing
alcohol solution and a soft dry lint free cloth, dampen cloth and wipe film clean, turn over and wipe the other
side as well, let the films dry completely before inserting into the scanner
For video instruction please Click Here
Sorting & Cleaning continued
9
Loading Filmstrips
Insert filmstrips with the emulsion (DULL) side down (SHINY side up), when inserting strips you may need to lift
the cover to be certain your film strips are being placed properly under the guides on the film feed holder (Fig.1
& 1a.), these guides aid in the negatives feeding properly into the scanner. When inserting a strips of 4 frames
they need to be inserted as far in as the line shown in (Fig. 2) to be accepted by the scanner for scanning, if
not inserted fully it cannot grab the film and begin scanning. 6 frame strips will stick out above the holder, the
software acknowledges proper insertion on the lower left of the main UI for directions on how to loading
capacity and configuring scan settings please Click Here:
Loading Filmstrips
Fig. 2
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Pacific Image Electronics Scanner
