OWC Data doubler Manuel utilisateur

DATA DOUBLER

Installation Guide

OWC Data Doubler

Introduction........................................................................ 1

1.1 Minimum Requirements

1.2 Package Contents

1.3 About This Manual

Installation..........................................................................3

2.1 Mounting a 2.5" SATA Drive to the Bracket

2.2 Installation by Laptop type

2.2.1 - Late 2008 13” MacBook (5,1) and Mid-2009 13” MacBook Pro (5,5)

2.2.2 - Late 2009 13” MacBook (6,1) and Mid-2010 13" MacBook (7,1)

2.2.3 - Mid-2010 13” MacBook Pro (7,1)

2.2.4 - Early / Late 2011 13” MacBook Pro (8,1) and Mid-2012 13” MacBook Pro (9,2)

2.2.5 - Late 2008 15” MacBook Pro (5,1), Mid-2009 15" MacBook Pro (5,3 and 5,4)

2.2.6 - Mid-2010 15” MacBook Pro (6,2)

2.2.7 - Early / Late 15” MacBook Pro (8,2) and Mid-2012 15” MacBook Pro (9,1)

2.2.8 - Early / Mid 2009 17” MacBook Pro (5,2)

2.2.9 - Mid-2010 17” MacBook Pro (6,1) and Early / Late 2011 17” MacBook Pro (8,3)

Support Resources..........................................................77

3.1 Troubleshooting

3.2 Contacting Technical Support

OWC Data Doubler Table of Contents

Contents

OWC Data Doubler Introduction

1.1 Minimum Requirements

• MacBook 13” (Late 2008, Late 2009, Mid 2010)

• MacBook Pro 13” (Mid 2009, Mid 2010, Early 2011, Late 2011, Mid 2012)

• MacBook Pro 15” (Late 2008, Mid 2009, Mid 2010, Early 2011, Late 2011,

Mid 2012)

• MacBook Pro 17” (Early 2009, Mid 2009, Early 2010, Early 2011, Late

2011)

• The Data Doubler works with 2.5 inch SATA drives (7mm or 9.5mm drive

height)

1.2 Package Contents

Installation screws (7)

OWC Data Doubler

5-Piece Toolkit

NOTE: Some kits do not come with a 2.5 inch SATA drive as pictured above.

1.3 About this manual

The images and descriptions may vary between this manual and the unit

shipped. Functions and features may change depending on the rmware

version. Please visit the product web page for the most recent product

specications.

Introduction

OWC Data Doubler Introduction

Your laptop is a static-sensitive device. It is susceptible

to invisible damage if not protected during installation.

We recommend proper grounding by using a

grounding strap. Make sure to work in a clean, static-

free area, and avoid wearing clothing that retains

static charges. For more information please visit:

www.owcdigital.com/support/anti-static

OWC Data Doubler Installation

2.1 Mounting a 2.5" SATA Drive to the Bracket

1. Align the drive to the connector on the green circuit board, then apply

gentle pressure in the direction shown below to fully connect the drive.

2. Use the two large, round-head Phillips screws from the kit to ax the drive

to the side of the Data Doubler bracket (screw hole locations shown in red).

The OWC Data Doubler and SATA drive are now ready for installation.

Installation

OWC Data Doubler Installation

2.2 Installation by Laptop type

2.2.1 Late 2008 13” MacBook (5,1) and Mid-2009 13” MacBook Pro (5,5)

IMPORTANT: before beginning, be sure that your laptop is fully shut down

and disconnected from all cables, including the power cable. If you have a

MacBook model 5,1, start with Steps 1-3. If you have a MacBook Pro model

5,5 start with Step 4.

1. Use the release lever (highlighted below in red) to release the battery cover,

then remove it (bottom photo). Recommended: Use the pull-tab on the

battery to remove it from the laptop, then set it aside.

OWC Data Doubler Installation

2. Next, remove the eight Phillips screws that secure the bottom cover to the

chassis (highlighted below).

Note: the three right-most screws along the top edge (shown in yellow)

are longer than the rest; install them in the same screw holes at the end of

the process. The rest can be used interchangeably in the remaining screw

holes.

3. Place your ngers on the bottom cover near the black vent opposite the

battery compartment, then lift the bottom cover. There are two snap clips

holding the cover in place; they will release when you lift the cover. Set the

bottom cover aside. You do not need to remove the SATA drive.

Proceed to Step 6.

OWC Data Doubler Installation

4. Remove the 10 Phillips screws from the bottom cover. Note: the three right-

most screws along the top edge (shown in yellow) are longer than the rest;

install them in the same screw holes at the end of the process. The rest can

be used interchangeably in the remaining screw holes.

5. Once the screws are removed, place your ngers along the bottom cover

near the black vent, then lift the bottom cover. There are two snap clips

attached to the cover that will release when you do this. Set the cover aside.

Recommended: before continuing, use the nylon pry tool to gently lift the

battery connector (highlighted in yellow) from the logic board.

OWC Data Doubler Installation

6. You should see the optical drive (indicated by the red arrow). This drive

needs to be removed before you can install the OWC Data Doubler.

7. Rotate the laptop so the optical drive is oriented in the same manner as the

drive shown below.

OWC Data Doubler Installation

8. Beginning on the right side of the optical drive, remove the two Phillips

screws that are highlighted in the photos below. Note: These screws are

not used when reassembling the laptop; store them in a safe place in case

you need them later.

Autres manuels pour data doubler

Table des matières

Autres manuels OWC Enceinte

OWC

OWC Mercury Elite-AL Pro Manuel utilisateur

OWC

OWC Mercury Elite Pro Dual Mode d’emploi

OWC

OWC ENVOY EXPRESS Manuel utilisateur

OWC

OWC Mercury Elite-AL Pro Manuel utilisateur

OWC

OWC Mercury Elite Pro Dual Mode d’emploi

OWC

OWC ThunderBay 4 Mode d’emploi

OWC

OWC Express Manuel utilisateur

OWC

OWC Value Line Manuel utilisateur

OWC

OWC TB2U3DKR2 Manuel utilisateur

OWC

OWC Mercury Elite RAID Manuel utilisateur

OWC

OWC Mercury Elite-AL Pro Manuel utilisateur

OWC

OWC Envoy Pro Manuel utilisateur

OWC

OWC U.2 NVMe Interchange System Mode d’emploi

OWC

OWC Mercury Elite Pro Dual mini Mode d’emploi

OWC

OWC Mercury Pro Mode d’emploi

OWC

OWC EXPRESS 4M2 Mode d’emploi

OWC

OWC Mercury Rack Pro 4 Bay Storage Enclosure Manuel utilisateur

OWC

OWC Envoy Pro Manuel utilisateur

OWC

OWC Mercury Elite-AL 800 Pro Manuel utilisateur

OWC

OWC Mercury Elite-AL Pro Manuel utilisateur

OWC

OWC Mercury On-The-Go Pro Manuel utilisateur

OWC

OWC Mercury Elite-AL Pro Manuel utilisateur

OWC

OWC Superslim Mode d’emploi

OWC

OWC Express Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur

OWC data doubler Manuel utilisateur

Manuels Enceinte populaires d'autres marques