OVERMOUNT EM-PLA Manuel utilisateur
EM-PLA/PLAB INSTALLATION GUIDE
Large Universal Cantilever Mount
Features
• Designed for 40"-58" Flat Panels
• Maximum weight capacity up to 125 lbs
• VESA compliant
• Lift and Lock for easy installation
• Integrated cable management
• CUL Approved
WARNING
•
THE WARRANTY WILL ONLY BE VALID IF YOU FOLLOW THE INSTRUCTIONS CAREFULLY.
•
If you do not understand the instructions, or are not sure you can follow them safely, contact a qualified
contractor.
•
Improper installation may cause serious injury and/or damage. It is recommended that a qualified
contractor install the EM-PLA / EM-PLAB.
• Make sure that the wall you plan to use will safely support four times the combined weight of the
mounted equipment, including its accessories.
• Under no circumstances should this product be mounted to metal studs.
• Never exceed the maximum load capacity of 150 lbs.
• A second person will be required to assist with several steps.
• Before beginning check that you have all the parts listed. Call 1-866-604-6966 to acquire any
missing parts.
TABLE OF CONTENTS
Installation tools..................................................................
Parts list..............................................................................
Mounting location.................................................................
Installation template.............................................................
Wall preparation..................................................................
Mounting to the wall............................................................
Assemble the adaptor plate.................................................
Configuring adaptor plate....................................................
Selecting the mounting hardware........................................
Attaching the display............................................................
Using cable management....................................................
Adjusting the display..........................................................
Maintaining the unit............................................................
3
3
3
4
4
6
7
7
7
8
9
9
10
2
NB012010
Installation tools
Electronic Stud Locater (Wooden stud installation only)
Variable Speed Electric Drill
Hammer Drill (Concrete installation only)
Drill Bits:
1/4" (6 mm) drill bit (Wooden stud installation only)
1/2" (13 mm) masonry drill bit (Concrete installation only)
Hammer (Concrete/Masonry installation only)
Ratchet Wrench with 11/16" (17 mm) socket
Philips head screwdriver
Parts List
ID Description Qty
APhilips M4*35mm 4
BPhilips M4*45mm 4
CPhilips M5*35mm 4
DPhilips M5*45mm 4
EPhilips M6*35mm 4
FPhilips M6*45mm 4
GPhilips M8*35mm 4
H Philips M8*45mm 4
I4
J4
K1
4
L
4
M
Round Washer 6
N
Square Washer 4
O
3/8"-3 1/2" Lag Bolts 6
P
QWall anchor 6
Step 1: Determine the Mounting Location
a)
b)
c)
d)
f)
e)
g)
Description
Wall Plate
Cable Panel
Mount Head
Arm Assembly
Qty
1
1
1
1
ID
a)
b)
c)
d)
Description
Adapter Panel
Adapter Bar
Adapter Bracket
Qty
1
2
2
ID
e)
f)
g)
Screw M6
Metal Washer
(∅6x∅10x1.2)
Metal Washer
(∅6x∅13x1.2)
8
4
4
h)
h) i) j)
i)
j)
M8*15 mm screw bolt
8.2*1.5*16 metal Washer
5 mm Allen wrench
5/8" spacer
3/4" spacer
To provide maximum viewing flexibility, the EM-PLA mount is capable of a wide range of motion.
This allows the plasma/LCD unit to be put in almost any position. When selecting the mounting
location make sure there is adequate space on all sides of the panel to allow for full range
articulation of the bracket.
3
NB012010
Step 2: The Installation Template
The installation template is designed to make
mounting the wall plate faster, easier and
more precise. The template includes a built in
dust channel to reduce clean up (Fig.1).
Step 3: Preparing the Wall Fig.1
Follow the instructions based upon your mounting surface:
3a Wooden Stud
3b Concrete/Masonry
3c Cinder Block
Step 3a: Mounting to Wooden Studs
The EM-PLA can be mounted onto two wooden studs, with center to center distances
between 15" and 17" (38-43 mm).
Using an electronic stud finder (Fig.2), locate the center of the two wooden studs at the
desired mounting location. Mark the stud center positions directly on the wall. Connect
the stud marks with a horizontal line and find the center between them to represent
where you wish the center of the screen to be located. Be sure to measure and mark the
center of this horizontal line.
Fig.2
Place the template on the wall, and then remove the tape strip from the back of the template.
Pin the template to the center mark on the wall. Using a level (bubble or laser ), level the
guide, and then press the adhesive backing against the wall to hold the guide in place.
Note: Depending upon the wall texture, you may need to use tape to hold the template in position.
Using a 1/4" (6 mm) drill bit, drill 6 pilot holes into the center of the studs (through the mounting hole
cut-out sections of the template), down to a depth of 3" (76 mm).
Carefully remove the template from the wall and discard. Hold the template in an upright position
so as not to spill the collected dust..
REMOVE
REMOVE
UP
4
NB012010
Step 3b: Mounting to Concrete/Masonry
WARNING
• NEVER drill into mortar joints! Fig.3
• Concrete must be 2000 PSI density minimum.
The wall plate can be mounted directly to concrete/masonry walls. Remove the tape strip
from the back of the template, and place the template in the desired location. Using a
bubble/laser level, align the template and then press the adhesive backing to the wall
which will hold the guide in place.
Note: Depending upon the wall texture, you may need to use tape to hold the template in position.
Using a 1/2" (13 mm) masonry drill bit, drill 6 mounting holes 31/8" (80 mm) deep into the
concrete/masonry surface. Drill through the mounting hole cut-out sections of the template.
Insert wall anchors into the mounting holes,and lightly tap them flush to the wall with a hammer (Fig.3).
IMPORTANT
Masonry anchors MUST be seated firmly against the masonry or concrete. If mounting to a
masonry wall covered with drywall/plaster, counter sink a larger hole through the drywall/plaster
to the concrete/masonry surface overlapping the mounting hole, so that the anchor can be
seated directly against the concrete/masonry surface.
Step 3c: Mounting to Cinder Block
WARNING
. Cinder Block must meet ASTM C-90 specifications.
. Mount to solid portion of block,generally 1" from the sides.
. NEVER drill into mortar joints!
. Use standard drill set on slow speed/high torque setting. DO NOT use hammer drill on cinder block.
. Verify that you have a minimum of 1 3/8" of actual concrete thickness in the mounting hole,
before inserting the wall anchor.
The wall plate can be mounted directly to cinder block walls.
Remove the tape stripe from the back of the template. Using a bubble level, hold the template in a
level position and then press the adhesive backing against the wall to hold the guide in place.
5
Hammer
Gently
Push in
Carefully remove the template from the wall and discard. Hold the template in an upright position
so as not to spill the collected dust..
NB012010
Note:Depending upon the roughness of the surface, you may need to hold the template in
place with tape.
Using a 1/2" (13 mm) drill bit, drill 6 mounting holes 31/8" (80 mm) deep into the cinder block
surface. Drill through the mounting hole cut-out sections of the template.
Insert wall anchors into the mounting holes,and lightly tap them flush to the wall with a hammer.(Fig.3)
IMPORTANT
Masonry anchors MUST be seated firmly against the concrete or masonry, If mounting to
a wall covered with drywall/plaster,counter bore a hole through the drywall/plaster around
the mounting hole location,so that the anchor can be seated directly against the concrete
or masonry.
Step 4: Mounting to the Wall
Remove the cantilever assembly from the box.
With the help of an assistant, carefully hold the mount in
position over the mounting holes, and then securely bolt
the wall plate to the wall with supplied washers (N) and
3/8"-3 1/2" lag bolts (P). See Fig.4.
Fig.4
IMPORTANT
Tighten lag bolts so that wall plate is firmly attached to wall,but DO NOT over tighten.
The lag bolts can be damaged by over tightening which will strip their threading.
Final tightening of lag bolts should be done by hand using a ratchet wrench and socket.
6
3/8”-3 1/2” lag bolt
round washer
wall plate
Carefully remove the template from the wall and discard. Hold the template in an upright position
so as not to spill the collected dust..
NB012010
Step 6: Configure the Adapter Plate
Step 5: Assemble the Adapter Plate
Fig.6.1
Fig.5.1
Fig.5.2
Step 7: Selecting the Mounting Hardware
(Fig.7).
Some displays will require the use of a spacer.
There are two spacers provided:
5/8" (16 mm) round nose spacer (L)
3/4" (19 mm) block spacer (M)
Fig.7
7
Attach the adapter panel to the adapter bars using four screws
and four metal washers (Fig.5.1.).
Attach the adapter brackets to the adapter bars using four
screws and four metal washers (Fig.5.2).
NOTE：In order to accomodate various panel sizes there are
five positions in which the brackets can be attached.
The adapter plate is of a universal design, and can be
attached to a wide range of flat panel display mounting
patterns up to VESA 400x600.
The easiest way to check for fit is to simply place the
adapter on the back of the display, with one mounting
bracket aligned with a set of vertical mounting holes (Fig.6.1).
Then, using the adapter's revolutionary rack and pinion self-
centering system, simply slide the other mounting bracket in
or out until it aligns with the second set of vertical mounting
holes (Fig.6.1). The adapter should now be horizontally
centered on the back of the flat panel display. In order to achieve
VESA 300mmx300mm mounting paterns, invert the mounting
brackets so that the mounting holes are on the inside.
Proceed to step 7 when the brackets are correctly aligned to
the mounting holes (Fig.6.2).
Fig.6.2
Adapter
Panel
Adapter
Bracket
Adapter
Bar
M6 Screw
Metal Washer
(￠6*￠10*1.2)
M6 Screw
Metal Washer
(￠6*￠13*1.2)
The spacers may be used individually,or may be snapped together to create one large
stacked spacer.The spacers have been designed to snap directly into the mounting rail for
ease in handling, and also include two different mounting holes to manage the various screw
sizes.
Generally,the 5/8" (L) is used on displays with slightly curved backs and /or recessed
mounting lands. The 3/4" spacer (M) is used on displays with curved backs, and stacked
spacers(L&M) will be used on displays with deeply curved backs and/or protruding accessories.
Step 8: Attach the Display
Place the adapter down on the back of the flat panel display.Align the
left mounting rail with the mounting holes on the back of the display panel.
Center the rail vertically over the back of the display,and secure using
the selected mounting screws (A-H), square washers (O) and any
required spacers (L&M) (Fig.8).
Note: Use the segmented mounting slots on the rails as a
means for vertically centering the adapter.
Fig.8
Now slide the opposite mounting rail into position,align it with the mounting holes, and secure with the
mounting hardware.
IMPORTANT
DO NOT over tighten the mounting screws, or the display may be damaged.
NEVER use a power driver to tighten the mounting screws.
With the help of an assistant, carefully lift the display and attach it to the mount head.
Tighten the screws (Fig.8.1).
Fig.8.1
8
8.2*1.5*16mm metal washer
M8*15mm screw bolt
mount head
NB012010
Step 9: Using Cable Management
The EM-PLA includes a cable management system where cable can
be routed along the length of the arm assembly.
Route the display cable along the entrance of the cable
management slot.(Fig.10)
Note: For optimal performance, route the AC power Fig.9
cable separately form the signal cables.
With all cables in place, pull the display in and out to be certain that the arm assembly
moves freely, without stretching or damaging the cables.
Step 10: Adjusting the Display
Roll Control - Horizontal leveling of the flat panel display.
Fig.13
Grasp the edge of the display and roll it up or down into a level position (Fig.13).
Tilt Adjustment - Raising or lowering the screen to improve viewing angle.
Grasp the upper and lower edges of the display, and then turn it to the desired tilt angle (Fig.14).
Fig.14
9
cable management
cable
Fig.15
The EM-PLA provides a wide range of adjustment possibilities to suit your environment.
To lock the tilt angle, tighten the tilt knob (Fig.15) securely.
NOTE: For heavier displays, never fully release the tilt knob without fully
supporting the display.
NB012010
The tilt lever includes a ratchet function, so that it can be lifted and Fig.16
repositioned for the next turn. To operate the ratchet, pull the lever
straight out, rotate it to an unobstructed position, release the lever,
and then turn it in the desired direction. Repeat as necessary until
the tilt tension is set properly (Fig.16).
Swivel- Adjust the flat panel display for off center viewing positions.
Grasp the side edges of the display and then swivel display into its desired
position (Fig.17).
Fig.17
Panning - Positions the flat panel display at an angle to the wall for viewing
from opposite sides of the room.
Grasp the side edges of the display and then swivel and pull the display
Fig.18
into desired position (Fig.18).
Retracting the Flat Panel Display - Positions the display against the wall.
Grasp the side edge of the display, swivel and pull the display into the center
position (Fig.19), and then gently push the display straight back towards the Fig.19
wall into the retracted position (Fig.20).
Note:Use care when moving the display to ensure that cables do not
become stretched or pinched.
Fig.20
Maintaining the EM-PLA
The arm assembly and wall plate may be cleaned with a soft sponge and mild solution of soap
and water.
Caution:Be sure not to get moisture on the electrical connections or the display.
tilt knob
10
NB012010
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
