Overland Storage NEO 8000 Manuel utilisateur

Introduction

IMPORTANT: Overland Storage requires that all NEO 8000

parts be removed and replaced by an Overland Storage

authorized service provider. Improper installation may

result in damage which voids existing warranties.

This document describes how to either remove and replace

or add a power supply module in a NEO 8000 Library from

Overland Storage.

Unpacking the Spare

Carefully unpack the spare part and verify that you have

all the parts:

•Power supply module

•These remove & replace/add-on instructions

WARNING: The GUI touch screen does not

completely shut off NEO 8000 system power. To

reduce the risk of electric shock or damage to

equipment, disconnect the power by unplugging

the power cords.

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent electrostatic

damage, observe the following precautions:

•Transport and store items in static-safe containers.

•Keep electrostatic-sensitive parts in their containers

until they arrive at static-free stations.

•Use a wrist strap and properly-grounded tools.

•Make sure you are always properly grounded when

touching a static-sensitive component or assembly.

•Keep the work area free of non-conductive materials.

•Avoid touching pins, leads, or circuitry.

A NEO 8000 power supply is designed as a single unit to

permit quick and easy installation or replacement.

1. At the front panel, power down the library.

2. Set the library circuit breakers to OFF (“O”), and

remove and retain the power cords.

3. If replacing an existing power supply, remove the old

module (Figure 1).

a. Completely loosen the captive fastener

thumbscrew in the lower left corner.

b. Pull the captive fastener all the way down.

c. Grab the handle and gently pull the power supply

module out.

There is some initial resistance as the module

releases from the backplane.

4. If adding a new power supply, remove the cover plate

by gently prying off it off. It is held in place by spring

latches. Figure 1. Power Supply Latch

NEO 8000 Library

Power Supply Module Spare

Remove & Replace/Add-On Instructions

Overview & Notes

NEO-8043

Adding or Replacing a Power Supply

NEO-8043

5. Slide the new power supply module into the empty

slot, pushing slowly until it seats firmly against the

backplane of the power supply case.

6. Lift the captive fastener up fully and tighten the

thumbscrew.

NOTE: If the fastener doesn’t lift completely, press the

power supply inward to fully connect it with the backplane.

7. Be sure the power switch on the new power supply is

in the ON (“|”) position.

8. Reconnect the power cords and turn the circuit

breakers to the ON (“|”) position.

The green LED on the new power supply should come on

during POST. If it doesn’t light up, check that the power

supply module is completely inside the case and in full

contact with the backplane.

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are

held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed

to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or

implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the product(s) or program(s) described

in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

Additional Help

You can get additional technical support on the Internet at support.overlandstorage.com,

or call 1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or

001-858-571-5555 x5 (International).

Autres manuels pour NEO 8000

Table des matières

Autres manuels Overland Storage Stockage

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage E Series Manuel utilisateur

Overland Storage

Overland Storage Neo Series Library Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Mode d’emploi

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage PowerLoaders AIT-2 Mode d’emploi

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage NEO XL Series Manuel utilisateur

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage SnapServer Manuel utilisateur

Overland Storage

Overland Storage NEO XL Series Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage SnapServerXSR 40 Manuel utilisateur

Overland Storage

Overland Storage ULTAMUS Manuel

Overland Storage

Overland Storage NEO Series Manuel utilisateur

Overland Storage

Overland Storage ULTAMUS RAID 4800 Manuel utilisateur

Overland Storage

Overland Storage SnapSAN S3000 Manuel de service

Overland Storage

Overland Storage SnapServer XSR 120 Manuel utilisateur

Overland Storage

Overland Storage SnapScale X2 Node Manuel utilisateur

Overland Storage

Overland Storage NEO S-Series Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur