Osmio Zero IP-II Manuel utilisateur
Osmio Zero Installation
Reverse Osmosis System
User Manual
WhatsApp +447852323666
Telephone: 0800 002 9533
Email: [email protected]
Contents
1 Safety Precautions
1.1 Power Safety Precautions
1.2 Setup Precautions
1.3 Usage Precautions
2 Product Description
2.1 Appearance Sketch Map
2.2 Display and Operation Interface
2.3 Product Specifications
3 Start Up
3.1 Introduction
3.2 Filling the Supply Pitcher
3.3 Power Connection
4 Use
4.1 Introduction
4.2 Flushing
4.3 Purification
4.4 Renew Water
4.5 Dispensing Water
4.6 Sleeping State
4.7 Power Off
5 Filters` Maintenance
5.1 Introduction
5.2 Filter Replacement
5.3 Failure State
6 Common Usage Problem
7 Quality Assurance
8 After-Sale Service
9 Electrical Schematic Diagram
1 Safety Precautions
1.1 Power Safety Precautions
• The system should be plugged into a normal UK 3 pin plug at your home
or workplace and not be used in addition to AC 220-240V, 220V.
• Should be used in a grounding socket with rated current above 10A.
• Should only be used on an electrical circuit with RCD.
• Please do not use this product if the power cord or plug is damaged or
when the plug is loose.
• If there is dust or water and other foreign matter on the power plug,
please wipe it clean before use.
1.2 Setup Precautions
• The system should not be installed near heating equipment, electric
heating products or other high-temperature places.
• The system should not be installed in a place of possible leakage of
combustible gases or near any flammable substances.
• The system should only be used indoors and positioned on a stable flat
surface avoiding direct sunlight and moisture.
Thank you for purchasing this product, please read this manual carefully
before using the system, and keep it for future reference. If you have any
questions about this machine, please call our customer service centre on
0800 002 9533.
Take Note: Boiling water is potentially dangerous.
It is the responsibility of the owner to take sensible precautions when operating
the boiling water function of the system and to instruct other family members
and other new users to operate it safely.
KEEP OUT OF REACH OF CHILDREN
1.3 Usage Precautions
• On first use or if the unit has been idle for more than 2 days, run a
complete cycle and discard the first batch of water produced. Fill your supply
pitcher with water and then allow the machine to run until it fills the internal
tanks. Dispense both ambient and hot water to ensure both hot and cold
internal tanks are flushed.
• Unknown liquids or foreign objects are prohibited.
• If there is any water leakage from the machine, please disconnect the power
and contact the customer service centre. Please ensure the Supply
Water Pitcher and the filters have been inserted correctly and fully into the
system.
• If there is any abnormal sound, smell, or smoke, etc., please disconnect the
power and contact the customer service centre.
• Do not disassemble or modify the system without professional guidance, please
contact the customer service centre if you need support.
• Do not move this product when it is in use.
• Do not use any detergent or alcohol based cleaner to clean the product, please
wipe the machine with a soft dry cloth.
• Do not grasp the water nozzle or the knob to move the machine.
• This product cannot be used by people who are physically or mentally disabled or
children unless supervised. Please keep it out of reach of children.
The filters on the system need to be changed every 6 months. We offer a 1 year
warranty for customers in medium hard up to 200 ppm Calcium Carbonate Hard-
ness and TDS of 250 ppm. For customers with harder or water with higher TDS, we
do not recommend this product unless you are happy to make be more frequent
membrane filter changes. The system is designed to shut off if there is blockage in
the membrane or prefilters. As the system recirculates the rejected water from the
membrane, the TDS level continually rises of the water entering the membrane
filter. Therefore, for those with water of higher TDS, more frequent membrane
changes are required.
IMPORTANT NOTE: You must empty the Supply Pitcher before
refilling it with fresh water as this can block your filters
2 Product Description
2.1 Appearance
1 Display Panel
2 Control Button (Rotate & Press)
3 Nozzle
4 Drip Tray Cover
5 Drip Tray
6 Power Plug
7 Supply Pitcher
8 Supply Pitcher Lid
FIGURE 1
2.2 Display and Operation Interface
A. Normal Water
B. Warm Water（40℃-50℃）
C. Hot Water（80℃-88℃）
D. Boiled Water (90℃-98℃）
E. Filtering Water
F. Renew Water
G. Filter Maintenance
H. Rotate (Choose the Water Temp)
I. Press to Get Water
FIGURE 2
2.3 Product Specifications
Electrical Properties
Rated Voltage : 220 - 240 V
Rated Frequency : 50 Hz
Rated Power: 2200W-2600W
Heating System
Rated Heating Power: 2180W-2580W
Hot Water Capacity: 30 l/h (≥ 90°C)
Filter Stages
1 - Quick-Change Sediment Filter 5μm: removes coarse particles, e.g.
Sand, rust, chlorine, lime
2 - Quick-Change activated carbon filter: removes chlorine and organ-
ic impurities
3 - Quick-Change Membrane 50GPD: removes all pollutants and
flavours to almost 100%
4 - Quick-Change Insertion Filters: Hygiene post filter antibacterial:
removes 99% of the bacteria and viruses and improves the taste.
Volume
Supply Pitcher 5 Litres
Pure Water Tank 1.5 L
Hot Water Tank 0.5 L
Dimensions:
405mm Length (Depth)
183mm Wide
388mm Height
Weight’: 7.1 kg
FIGURE 3
FIGURE 4
3 Start Up
3.1 Introduction
• Please place the system in a cool, ventilated, solid horizontal surface, away
from any heat source. The system comes ready installed with the filters so you can
right away fill the Supply Pitcher.
3.2 Filling the Supply Pitcher
• Open the tank lid (Figure 3).
• Lift the Supply Pitcher out.
• Fill the Supply Pitcher with fresh water
and put it back on to the base (Figure 4)
and close the lid.
• Note: machine will not run without the
Supply Pitcher Lid clipped on.
.
3.3 Power Connection
• Insert the power plug into the socket (see Figure 1). The system will beep and light
up which indicates the machine is ready to use.
Note: This product is only suitable for AC 220-240V, 220V power supply, and
should be used alone or over rated 10A with a earthed socket.
4 Usage
4.1 Introduction
• At first, produce and dispense 5 litres of water which you then dispose of
by dispensing all the cold and hot water. This will flush out any loose filter
media. It is normal to see black water when using new filters.
• If there is water leakage from the machine, please disconnect the power
and contact the customer service centre. If there is any abnormal or
unexpected sound, smell, or smoke, etc., please disconnect the power and
contact the customer service centre.
4.2 Flushing
• After the setup, the machine automatically enters the flushing state and
works for 120 seconds. In the flushing state, the filtering symbol of the
display interface light will be on (see Figure 2) .
4.3 Purification
• After flushing, the machine automatically enters the filtering state. The
filtering symbol on the display interface light will be on (see Figure 2).
4.4 Replace Water
• The system will detect the source water quality in normal operation. If
the water level is lower than the set level, the user will be prompted to
replace the source water. You must empty the Supply Pitcher every time it
is refilled. The renew water symbol of the display interface
will light on at this time (see Figure 2).
IMPORTANT NOTE: You must empty
the Supply Pitcher before refilling it
with fresh water as this can block
your filters
4.5 Dispense Water
• Place the water container on the tray (see Figure 1). Rotate the knob to
select the desired water temperature (Figure 5), and then click on (or push
on for 3 second) the middle part of the knob (see Figure 6) to dispense one
cup (or bottle) of water. Click the knob again if you want to stop getting
water. Note: the system will automatically stop water after 30 seconds if
you do not click the knob and will automatically stop after 60 seconds if you
hold the button for 3 seconds.
4.6 Sleeping state
• The system will automatically enter sleeping state when it is idle for more
than 1 hour. If there is any knob or button operation, it will immediately
return to service and then flush for 20 seconds.
4.7 Power off
• The system will automatically power off if the machine stays in sleeping
mode for 1 hour. If there is any knob or button operation, it will power on
automatically.
http://www.osmiowater.co.uk/manuals/MiniDUE%20Instruction%20Booklet.pdf
FIGURE 5 FIGURE 6
Table des matières
Manuels Système d'eau populaires d'autres marques
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur
Microline
Microline T.F.C.-4 Manuel
Eureka Forbes
Eureka Forbes Aquaguard Select Manuel utilisateur
Cetetherm
Cetetherm AquaEfficiency Manuel utilisateur
