OSE C.ITOH CI-5000 Manuel utilisateur

OSE C.ITOH CI-5000 Dot Matrix Printer

Print Method Rugged dot matrix impact bi-directional

Print Speed 540cps @ HQ (12cpi), 450cps @ (10cpi), 110cps @

NLQ, 73cps @ Double Density LQ

Print Head 18 wire (2 X 9 wire parallel)

Printer Life 500 million characters

Resolution 330 dots per inch

Interfaces Centronics Parallel:

RS-232 serial

RS-423 interfacing built in

Emulations IBM Proprinter XL, DEC LA50/LA75/LA210, Epson

FX-286e

Paper Handling Friction feed for cut sheets

Pin Feed (continuous/perforated paper)

Forward and reverse feed

Rear and bottom feed

Rear exit/Top exit

Control Panel

Buttons/Keys

ON LINE: Toggles unit between online and offline.

FWD LN FEED: Advances paper one line. When held down simultaneously

with RESET button advances paper one dot row.

FORM FEED: Advances paper form length stored in Present Users Number's

attribute field 10. If Paper Park is active, this key will restore paper to its printing

position. When held down simultaneously with RESET button puts printer in

PAPER PARK mode. Pressing this button once again will take printer out of

PAPER PARK mode and restore paper to its printing position.

RESET: Places printer offline and clears any alarm display if error condition has

been corrected.

QUIET/SET-UP: Activates SET-UP mode.

REV LN FEED: Backs up paper one line. When held down simultaneously with

RESET allows paper to back up one dot row.

Note:

Do not use this button with bottom feeding paper or multipart forms.

TEAR FORM: Places paper at tear line. If button is pressed a second time,

printer will return paper to print position. Paper will also return to print position by

pressing this button and the RESET button simultaneously.

LEDs/Lights

POWER (Green): Indicates unit is functioning.

ON LINE (Green): Indicates unit is online.

ALARM (Red): Indicates unit is in an error status.

SET-UP (Yellow): Indicates printer is either in SET-UP or CONFIGURATION

mode.

DISPLAY WINDOW: Indicates status and selected choices.

Self-test

1. Ensure printer power is off.

2. Load continuous feed paper of at least 14 inch width (136 columns wide).

3. Hold down the RESET key while simultaneously pressing the QUIET/SETUP

key. This will put printer in CONFIGURATION mode.

4. Press the REV LN FEED key until field "91" appears and "TEST PRINT

PATTERN" appears in display window.

5. Press the ON LINE key to activate test printing.

6. To stop test printing press ON LINE key once again.

Cover Removal

Lift at both front corners of printer, moving them up and back until top cover is in a

resting position at approximately a 90 degree angle.

Configuration

General Users SET-UP Mode

Be sure printer is offline and press the QUIET/SETUP button. The display will

reflect "USER NUMBER" and the current user number will appear.

Configuration for System Managers or Operators

Ensure printer is offline then hold down RESET and QUIET/SETUP key simultane-

ously. The display will reflect "USER NUMBER" and the current user number will

appear.

Once in USER NUMBER mode you have to select a number.

1. Use FORM FEED button to advance one User Number at a time.

2. Press TEAR FORM button to back up one User Number at a time.

3. Once a USER NUMBER is selected you can either go back to offline state or

into FIELD mode.

Offline State

Press ON LINE or QUIET/SET-UP button to place printer back offline.

96-03-29 Copyright IBM Corporation 1996.

C.ITOH CI-5000 Dot Matrix Printer OSE

Field Mode

Press either FWD LN FEED or REV LN FEED button to activate FIELD Mode. In

this mode the buttons/keys function as follows:

ON LINE: Prints attribute values and then puts printer offline.

FWD LN FEED: (Field Scroll Forward) Advances to next field.

FORM FEED: (Menu Scroll Forward) Selects next menu choice for current field.

RESET (Clear) Resets this User Number attribute list to its last-saved working

values.

QUIET/SET-UP: (Save) Exits FIELD mode, saves choices, puts printer offline.

REV LN FEED: (Field Scroll Backward) Backs up one field.

TEAR FORM: (Menu Scroll Backward) Moves to lower number menu choice.

Selecting an Attribute Field

1. Ensure printer is offline.

2. Press QUIET/SET-UP button once to attain SET-UP mode.

3. Press FORM FEED button until "User Number 3" appears in display window.

4. Press FWD LN FEED button until the desired field is reached. Display should

have the following format:

3-13/1 CPI

MENU ITEM: Working value 1 cpi.

ATTRIBUTE FIELD:Field 13 is Character Pitch

USER NUMBER IS 3

5. To change menu items press FORM FEED button.

Changing Attribute Fields

1. Ensure printer is offline.

2. Press QUIET/SET-UP button to establish SET-UP mode.

3. Press either FORM FEED or TEAR FORM button to toggle between User

Number selections (selections range between 0 and 3).

4. Press FWD LN FEED to activate FIELD mode.

5. Use FWD LN FEED or REV LN FEED buttons to toggle between field

selections.

6. Use either FWD LN FEED or TEAR FORM button to select desired menu

item.

7. Exit FIELD mode by pressing QUIET/SET-UP button.

Changing to IBM Emulation Mode

1. Place printer in either SET-UP or CONFIGURATION mode.

2. Press FORM FEED button to enter User Number selections. Choose a User

Number.

Note:

Numbers 0 through 2 are stored in non-volatile memory where con-

tents are not lost when printer is turned off. User Number 3 is a "scratch" list

designed for frequent temporary changes.

3. Press FWD LN FEED button to access Attribute Field Selection and choose

"00"(Emulation Mode) and menu item "01" (IBM Emulation Mode).

4. Choose attribute field "01" (Emulation level); choose menu item "01" (IBM

Emulation Mode).

5. Press QUIET/SET-UP button to exit session.

Display Codes for IBM Emulation

Code Description Function Protection Type Notes

12 Line

Spacing Sets number of

lines per inch. Unprotected This setting does

not effect the

action of control

panel settings

numbered 10.

13 Character

Pitch Determines the

number of charac-

ters per inch

Unprotected The following

selections cannot

be attained in the

IBM Proprinter XL:

13.3 CPI, 15 CPI

and 20 CPI.

14 Print Quality Determine printing

quality level. Unprotected

17 Left Refer-

ence Justifies left edge

of print area Unprotected Initial setting is

0/10.

18 Right Refer-

ence Justifies right edge

of print area Unprotected Default setting is

136/10 inch from

the left top.

19 Print Direc-

tion Uses either

unidirectional or

bidirectional

printing.

Unprotected For best printing

speed set field 13

to 12 CPI HS and

use bidirectional

printing.

21 Font for

Zero Changes font used

for digit "0" Unprotected

22 Skip Perfo-

ration Used to establish

skip modes during

printing if there is

perforated paper.

Unprotected

23 Wraparound Determines proc-

essing of charac-

ters at right

justification.

This field will only

be displayed in

CONFIGURATION

mode.

Printer will wrap

text around when

in WRAP mode

but not in TRUN-

CATE mode.

24 Data Error Produces either a

reversed question

mark or a space

when an error is

detected.

This field will only

be displayed in

CONFIGURATION

mode.

25 LQ Char-

acter Gen-

erator

Determines which

character gener-

ator ROM to use

when powering up

unit.

This field will only

be displayed in

CONFIGURATION

mode.

When a font car-

tridge is installed,

printer will use that

font selection and

disregard menu

item selection.

26 Character

Set Determines speci-

fied character set Unprotected Selected set is

used on power-on

or reset.

27 Define

Character

Set

Not used in IBM

operations.

Code Description Function Protection Type Notes

00 Emulation

Mode Selects type of

printer emulation. Unprotected To activate an

external emulation

make sure it is

plugged in before

operating in this

mode.

28 Graphic

Character Not used in IBM

operations

31 Alarm Tone Engages or disen-

gages alarm sound

for errors

This field will only

be displayed in

CONFIGURATION

mode.

01 Emulation

Level Selects emulation

of either the IBM

Proprinter XL or

Epson FX-286e.

Unprotected

33 Top Margin Establishes dis-

tance between top

of form and where

print begins.

This field will only

be displayed in

CONFIGURATION

mode.

02 EEPROM

Store Determines

whether attribute

value list are

retained after

printer is turned

off.

Unprotected

34 Top of Form

Position Establishes Top of

Form guidelines for

automatic paper

feeding.

This field will only

be displayed in

CONFIGURATION

mode.

This setting will

effect operation of

field 33.

35 Switch Tone Engages or disen-

gages audible

sound when keys

are pressed.

This field will only

be displayed in

CONFIGURATION

mode.

10 Form

Length Establishes the

form length in units

of lines.

Unprotected Form length may

be from 1 to 132

lines. Form length

is expressed in

1/6" lines per

page. Use FORM

FEED or TEAR

FORM button to

select desired line

setting.

40 Interface Allows selection of

communication

interface.

This field will only

be displayed in

CONFIGURATION

mode.

Code Display Reflects Description

2CI-8 IBM/TSS Internal Use Only

OSE C.ITOH CI-5000 Dot Matrix Printer

Changing to DEC Emulation Mode

1. Place printer in either SET-UP or CONFIGURATION mode.

2. Press FORM FEED button to enter User Number selections. Choose a User

Number.

Note:

Numbers 0 through 2 are stored in non-volatile memory where con-

tents are not lost when printer is turned off. User Number 3 is a "scratch" list

designed for frequent temporary changes.

3. Press FWD LN FEED button to access Attribute Field Selection and choose

"00"(EMULATION mode) and menu item "02" (DEC EMULATION mode).

4. Choose attribute field "01" (Emulation level); choose menu item "01" (IBM

EMULATION mode).

5. Press QUIET/SET-UP button to exit session.

Code Description Function Protection Type Notes Code Description Function Protection Type Notes

01* 40/Centronics Establishes

Centronic parallel

port

46 RTS Busy

Sync Establishes syn-

chronization

between RTS

signal of serial

interface with busy

signal.

This field will only

be displayed in

CONFIGURATION

mode.

02 40/RS-232C Establishes

RS-232C serial

interface. 47 Offline

Deselect Allows and disal-

lows data reception

while unit is in

OFFLINE mode.

This field will only

be displayed in

CONFIGURATION

mode.

03 40/RS-423A Establishes

RS-423A Serial

interface.

41 Data Bits Establishes serial

interface data

length.

This field will only

be displayed in

CONFIGURATION

mode.

50 PE

Detection Establishes

whether paper end

feature will be

enabled.

This field will only

be displayed in

CONFIGURATION

mode.

If in operation

paper will stop 1/3

inch from papers

end.

Code Display Reflects Description 62 Overrun

Buffer Establishes buffer

size for overrun

usage.

This field will only

be displayed in

CONFIGURATION

mode.

01 41/7 bits 7-bit data length

02* 41/8 bits 8-bit data length

42 Serial Inter-

face Pro-

tocol

Establishes Serial

Protocol type This field will only

be displayed in

CONFIGURATION

mode.

63 Initial

ON/OFF

State

Determines state

of print after power

up.

This field will only

be displayed in

CONFIGURATION

mode.

Code Display Reflects Description 70 ASF Establishes Auto-

matic Sheet Feed

operations.

This field will only

be displayed in

CONFIGURATION

mode.

01 42/RESTRT-H Restraint High,

RS232 pin 11

02 42/RESTRT-L Restraint Low,

RS232 pin 11 71 Auto

Loading Control cut sheet

autoloading. This field will only

be displayed in

CONFIGURATION

mode.

When not automat-

ically sheet feeding

the FORM FEED

button can be

used to load

paper.

03* 42/XON/XOFF XON/XOFF

04 42/DTR DTR protocol pin

20 goes BUSY

when only buffer

space left is the

overrun buffer;

READY when

buffer level returns

to free space of at

least 1K bytes plus

overrun buffer size.

80 Automatic

CR on LF Establishes CR

after LF This field will only

be displayed in

CONFIGURATION

mode.

81 Automatic

LF on CR Determines

whether printer

follows each car-

riage return with a

line feed.

This field will only

be displayed in

CONFIGURATION

mode.

43 Stop Bits Establishes

number of stop bits

in each serial data

frame.

This field will only

be displayed in

CONFIGURATION

mode. 82 Can Code

Handling Establishes effect

of CAN code. This field will only

be displayed in

CONFIGURATION

mode.

Code Display Reflects Description

01* 43/1 bit 1 stop bit used.

(default) 90 HEX Dump Toggles between

normal and

Hexadecimal

printing

This field will only

be displayed in

CONFIGURATION

mode.

02 43/2 bit 2 stop bits used.

44 Parity Establishes parity

to be used. This field will only

be displayed in

CONFIGURATION

mode.

When field 41 is

established at 8

bits, Mark and

Space are treated

as No Parity.

91 Test Print

Pattern Establishes Self-

test print pattern This field will only

be displayed in

CONFIGURATION

mode.

There are two

modes of opera-

tion Sliding and

Repeat. Sliding

will move the char-

acters being

printed. Repeat

will reproduce

same character

over.

Code Display Reflects Description

01* 44/No Parity No Parity

02 44/Odd Odd Parity

03 44/Even Even Parity

04 44/Ignore Ignore Parity 92 Test Print

Character Establishes the

character being

used as test print.

This field will only

be displayed in

CONFIGURATION

mode.

Select a character

from A to Z in the

ASCII set.

45 Baud Rate Establishes data

transmission rate

for serial interface

This field will only

be displayed in

CONFIGURATION

mode.

Code Display Reflects Description

01 45/9600 BPS Use 9600 baud

02 45/4800 BPS 4800 baud

03 45/2400 BPS 2400 baud

04 45/1200 BPS 1200 baud

05 45/600 BPS 600 baud

06 45/300 BPS 300 baud

07 45/19200 BPS 19200 baud

96-03-29 Copyright IBM Corporation 1996.

C.ITOH CI-5000 Dot Matrix Printer OSE

Display Codes for DEC Emulation

The following codes and numbers differ from IBM and Epson emulation, but all other

codes are identical.

1. Place printer in either SET-UP or CONFIGURATION mode.

2. Press FORM FEED button to enter User Number selections. Choose a User

Number.

Note:

Numbers 0 through 2 are stored in non-volatile memory where con-

tents are not lost when printer is turned off. User Number 3 is a "scratch" list

designed for frequent temporary changes.

3. Press FWD LN FEED button to access Attribute Field Selection and choose

"00"(EMULATION mode) and menu item "01" (IBM/EPSON EMULATION

mode).

4. Choose attribute field "01" (Emulation level); choose menu item "02" (Epson

FX-286e Emulation)

5. Press QUIET/SET-UP button to exit session.

Display Codes for Epson Emulation

The following codes and numbers are different from IBM and DEC emulation, but all

other codes are identical.

Code Description Function Protection Type Notes

02 42/RESTRT-L Restraint Low,

RS232 pin 11

Code Description Function Protection Type Notes 03* 42/XON/XOFF XON/XOFF

01 Emulation

Mode Establishes DEC

printer type. Unprotected Enhanced

instructions

have been

set to the

emulations.

04 42/DTR DTR protocol pin 20

goes BUSY when

only buffer space left

is the overrun buffer;

READY when buffer

level returns to free

space of at least 1K

bytes plus overrun

buffer size.

Code Display Reflects Description

01* 01/LA210 Relates to Level 2

commands and

Level 1 commands

plus the C.Itoh

enhancements. 43 Stop Bits Establishes number

of stop bits in each

serial data frame.

This field will only be

displayed in CON-

FIGURATION mode.

02 01/LA210 ID LA75 emulation,

Level 2 operation.

Relates to Level 2

commands and

Level 1 commands

plus the C.Itoh

enhancements.

Allows for a LA210

ID to host upon

request for identifica-

tion.

Code Display Reflects Description

01* 43/1 bit 1 stop bit used.

(default)

02 43/2 bit 2 stop bits used.

44 Parity Establishes parity to

be used. This field will only be

displayed in CON-

FIGURATION mode.

When field

41 is estab-

lished at 8

bits, Mark

and Space

are treated

as No Parity.

03 01/Level 2 ID LA75 emulation,

Level 2 operation.

Relates to Level 2

commands and

Level 1 commands

plus the C.Itoh

enhancements.

Allows for a LA210

ID to host upon

request for identifica-

tion.

Code Display Reflects Description

01* 44/No Parity No Parity

02 44/Odd Odd Parity

03 44/Even Even Parity

04 44/Ignore Ignore Parity

45 Baud Rate Establishes data

transmission rate for

serial interface

This field will only be

displayed in CON-

FIGURATION mode.

04 01/Level LA75 emulation,

Level 1 operation:

LA50 printer emu-

lation plus response

to C. Itoh enhance-

ments.

Code Display Reflects Description

01 45/9600 BPS 9600 Baud

02 45/4800 BPS 4800 Baud

03 45/2400 BPS 2400 Baud

26 Define Char-

acter Set GL,

Establishes char-

acter set for GL, G0 Unprotected 04 45/1200 BPS 1200 Baud

05 45/600 BPS 600 Baud

27 Define Char-

acter Set G1 Establishes char-

acter set for G1 06 45/300 BPS 300 Baud

07 45/19200 19200 Baud

28 Define Char-

acter Set

GR, G2

Establishes char-

acter set for GR, G2. Unprotected

29 Define Char-

acter Set G3 Establishes char-

acter set for G3 Unprotected

40 Interface Allows selection of

communication inter-

face.

This field will only be

displayed in CON-

FIGURATION mode.

Code Display Reflects Description

01* 40/Centronics Establishes

Centronic parallel

port

02 40/RS-232C Establishes RS-232C

serial interface.

03 40/RS-423A Establishes RS-423A

Serial interface. Code Description Function Protection Type Notes

41 Data Bits Establishes serial

interface data length. This field will only be

displayed in CON-

FIGURATION mode.

01 Emulation

Mode Establishes Epson

FX-286 printer type Unprotected Enhanced

instructions

have been

set to the

emulations.

Code Display Reflects Description

01 41/7 bits 7-bit data length 27 Define Char-

acter Set Determines interna-

tional characters to

use

Unprotected

02* 41/8 bits 8-bit data length

42 Serial Inter-

face Protocol Establishes Serial

Protocol type This field will only be

displayed in CON-

FIGURATION mode. 28 Graphics

Character Determines italics or

graphic characters Unprotected

Code Display Reflects Description 40 Interface Determines commu-

nication interface. This field will only be

displayed in CON-

FIGURATION mode.

01 42/RESTRT-H Restraint High,

RS232 pin 11

4CI-8 IBM/TSS Internal Use Only

OSE C.ITOH CI-5000 Dot Matrix Printer

Error Codes

The message "DATA IN BUFFER" may appear in display window signifying that

there is still data stored in buffer that needs to be released. Press the RESET

button to clear out existing information in buffer and allow printer to enter SETUP

mode.

Adjustments

Paper Thickness lever (located on top left side of printer):

The symbol with multiple sheets is used to print out multiple forms as well as envel-

opes. The nine positions between multiple forms and single sheet forms are used

according to paper thickness. Middle location settings are designated for four- to

six-part forms. One line which is wider than the others shown is used for standard

continuous or cut-sheet paper.

Printer Options

Line Printer Emulation Cartridge

Font Cartridges

Color Adapter Kit

Color Ribbon Cartridge

Automatic Sheet Feeder for cut sheets

Field Replaceable Units (FRUs)

05 PAPER JAM Check paper path for jamming.

Code Description Function Protection Type Notes 06 P.S. LEVER Mismatch with paper being used and lever

selected.

Code Display Reflects Description 11 DATA ERR Serial interface error during data reception.

01* 40/Centronics Centronics parallel

port 12 ESC FAULT Wrong emulation code has been sent from

computer.

02 40/RS-232C RS-232C serial inter-

face 13 OVERRUN ERR Buffer is in over loaded condition.

14–19 These alarms are not in current use.

21 HOME ERROR Print head is not returning to home position.

03 40/RS-423A RS-423A serial inter-

face 22 MOTOR HALT Carriage motor speed is not accurate.

23–29 These alarms are not in current use.

41 Data Bits Establishes serial

interface data length. This field will only be

displayed in CON-

FIGURATION mode.

40 Not in use as a alarm.

41 ROM PACK ERR Bad ROM cartridge error.

42 Not in use as a alarm.

43 ROM ERR Data error in the EEPROM associated with

non-volatile memory.

Code Display Reflects Description

01 41/7 bits 7-bit data length 44 RAM1 ERR Error associated with read/write check.

45 RAM2 ERR Error associated with read/write check.

02* 41/8 bits 8-bit data length 46–49 These alarms are not in current use.

42 Serial Inter-

face Protocol Establishes Serial

Protocol type This field will only be

displayed in CON-

FIGURATION mode.

Code Display Reflects Description

01 42/RESTRT-H Restraint High,

RS232 pin 11

02 42/RESTRT-L Restraint Low,

RS232 pin 11

03* 42/XON/XOFF XON/XOFF

04 42/DTR DTR protocol pin 20

goes BUSY when

only buffer space left

is the overrun buffer;

READY when buffer

level returns to free

space of at least 1K

bytes plus overrun

buffer size.

43 Stop Bits Establishes number

of stop bits in each

serial data frame.

This field will only

be displayed in

CONFIGURATION

mode. Description IBM P/N

PTR, NLQ, SER, RS232, 31F0244

Code Display Reflects Description

01* 43/1 bit 1 stop bit used.

(default)

02 43/2 bit 2 stop bits used.

44 Parity Establishes parity to

be used. This field will only be

displayed in CON-

FIGURATION mode.

When field

41 is estab-

lished at 8

bits, Mark

and Space

are treated

as No Parity.

Code Display Reflects Description

01* 44/No Parity No Parity

02 44/Odd Odd Parity

03 44/Even Even Parity

04 44/Ignore Ignore Parity

45 Baud Rate Establishes data

transmission rate for

serial interface

This field will only be

displayed in CON-

FIGURATION mode.

Code Display Reflects Description

01 45/9600 BPS 9600 Baud

02 45/4800 BPS 4800 Baud

03 45/2400 BPS 2400 Baud

04 45/1200 BPS 1200 Baud

05 45/600 BPS 600 Baud

06 45/300 BPS 300 Baud

07 45/19200 19200 Baud

01 COVER OPEN Close top cover of printer.

02 PAPER OUT Check paper path and insertion.

04 PAPER SET Both continuous paper and cut sheets are

inserted simultaneously.

96-03-29 Copyright IBM Corporation 1996.

C.ITOH CI-5000 Dot Matrix Printer OSE

Service Documentation

There is no service documentation available to be ordered at this time.

IBM machine type: 1003-C19

1515-CXX

Tech Support 800-877-7764

6CI-8 IBM/TSS Internal Use Only

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur