Oregon CS1200 Manuel de programmation

CS1200 CHAINSAW

Quick Start Instructions

ASSEMBLING THE GUIDE BAR AND

SAW CHAIN

STEP 2: Loosen the chain tensioning

dial (A) as far as it will go. Then fully

loosen the side cover release knob (B)

and remove the side cover.

RED

This sheet is meant to be a suppliment, not a replacement for your operator’s manual.

What’s in the box?

The chainsaw requires some

assembly before use. These items

are included in the box.

1) Powerhead

2) Guide Bar

3) Saw Chain

4) Blade Cover

5) Side Cover

6) Instruction Manual

IMPORTANT SAFETY NOTICE

Wear protective gloves when handling chainsaw chain.

After removing the chainsaw from the box, inspect it

carefully to ensure no damage has occurred during

shipping and that no parts are missing. If any parts

are damaged or missing, do not use the chainsaw.

Contact Oregon® to obtain replacement parts. For

country-specic telephone numbers, see “Customer

Service by Country”.

ATTENTION! SAFETY NOTICE

Unplug the chainsaw

FILLING THE BAR AND CHAIN OIL

RESERVOIR

STEP 1: Place the chainsaw on a firm,

flat surface, so that the oil cap (A) is

on top.

• Clean any debris from the cap area.

• Remove the cap.

• Carefully pour 100 ml of bar and

chain oil into the reservoir.

If the reservoir is totally full on

initial startup, it can slow down

the prime. We suggest 90% full.

STEP 3: Loop the

saw chain onto

the bar and drive

sprocket so that the

cutters are facing in

the correct direction.

CS1200 CHAINSAW

Quick Start Instructions

STEP 4: Place the guide bar on the

bar pad by sliding the bar slot over the

alignment ange, with the mounting

stud inserted through the slot in

the guide bar (A). Align the lower

tensioning hole on the guide bar to

seat on the tensioning stud (B).

STEP 6: Adjust chain tensioning dial

(A) then fully tighten the side cover

knob (B).

RED

STEP 5: Install the side cover, making

sure the chain catcher and side

cover tabs are seated in their proper

locations (A), then lightly tighten the

side cover knob (B). Do NOT fully

tighten at this stage.

5RED

TENSIONING THE SAW CHAIN

STEP 8:

Loosen the side cover release

knob slightly, but do not remove the

side cover.

STEP 9:

Hold up the nose of the guide

bar (A) and turn the chain tensioning

ring clockwise.

STEP 10:

Tighten the chain tensioning

ring until the lowest cutters

underneath the bar solidly contact the

bar (B).

STEP 11:

Lightly pull on the chain. The tension is correct when the chain snaps back

after being pulled 3 mm away from the guide bar.

STEP 12:

After a short period of use, allow the chain to cool, unplug the chainsaw

and check the tension again. Watch tension carefully for the rst half-hour of use and

periodically throughout the life of the chain readjusting as required when the chain

and bar are cool to the touch. Never tension chain when it is hot.

Chain will stretch as a result of normal use, however, insucient oil, aggressive use,

or failure to perform recommended maintenance can lead to premature stretching.

INCORRECT CORRECT

IMPORTANT: The saw chain must be

properly tensioned before using.

ATTENTION! SAFETY NOTICE

Wear Chainsaw Protective Gloves

WARNING An electric power tool that is plugged in can start accidentally.

Unplug the chainsaw before preparing for use or performing maintenance.

WARNING If the chain is still loose when the saw is at maximum tension, replace

the chain.

IMPORTANT Only tension the saw chain when the chain is cool.

ATTENTION! SAFETY NOTICE

Unplug the chainsaw

8BLACK

Autres manuels Oregon Tronçonneuse

Oregon

Oregon CS1500-091 Instructions de fonctionnement

Oregon

Oregon CS250 Manuel utilisateur

Oregon

Oregon CS1500 Manuel de programmation

Oregon

Oregon CS250 Guide de l'utilisateur

Oregon

Oregon 680ES Manuel utilisateur

Oregon

Oregon CS1500 Manuel de programmation

Oregon

Oregon CHAINSAW Guide de l'utilisateur

Oregon

Oregon CS1500 Instructions de montage

Oregon

Oregon THPCS16 Instructions d'installation et d'entretien

Oregon

Oregon CS1500-092 Guide de l'utilisateur

Oregon

Oregon CS1200-092 Guide de l'utilisateur

Oregon

Oregon CS1400 Manuel de programmation

Oregon

Oregon CHAINSAW Guide de l'utilisateur

Oregon

Oregon CS1500-091 Guide de l'utilisateur

Oregon

Oregon Qualcast PC40 Manuel utilisateur

Oregon

Oregon JW3800 Instructions d'installation et d'utilisation

Oregon

Oregon CS250 Manuel utilisateur

Oregon

Oregon Harvester Manuel utilisateur

Oregon

Oregon PN2500N Manuel utilisateur

Oregon

Oregon CS1200-091 Guide de l'utilisateur

Oregon

Oregon CS300 Guide de l'utilisateur

Oregon

Oregon CS250 Guide de l'utilisateur

Oregon

Oregon JW3800 Manuel utilisateur

Oregon

Oregon CHAINSAW Guide de l'utilisateur

Manuels Tronçonneuse populaires d'autres marques

Bushranger

Bushranger CS4210 Manuel utilisateur

Husqvarna

Husqvarna 136, 141 Manuel utilisateur

Echo

Echo CS-330EVL Manuel utilisateur

HART

HART HLCS01 Manuel utilisateur

Homelite

Homelite UH10817 Manuel utilisateur

Westfalia

Westfalia SCS 725 Manuel utilisateur

Nakayama

Nakayama EC2050 Manuel utilisateur

The Handy

The Handy THPCS16 Manuel utilisateur

McCulloch

McCulloch PRO MAC 54 Manuel

Husqvarna

Husqvarna 359 E-tech Manuel utilisateur

Craftsman

Craftsman 358.352162 Manuel utilisateur

Craftsman

Craftsman 358.350270 Manuel utilisateur

Craftsman

Craftsman 358.351610 Manuel utilisateur

Echo

Echo CS-8001(6digits)(36) Mode d’emploi

Poulan Pro

Poulan Pro 545047544 Manuel utilisateur

Ryobi

Ryobi RY3714VNM Manuel utilisateur

Homelite

Homelite Ranger UT10926 Manuel utilisateur

McCulloch

McCulloch TimberBear TM502 Manuel utilisateur