Oregon Scientific RMR132HG Manuel utilisateur

Multi-Channel IN-OUT Thermo-Hygrometer

with Cable Free Sensor and RF Clock

MODEL: RMR132HG

USER MANUAL

INTRODUCTION

Congratulations on your purchase of the RMR132HG

Multi-Channel In-Out Thermo-Hygrometer with 433MHz cable

free sensor and radio-controlled calendar clock.

The basic package comes with a main unit, which is the

temperature and calendar clock station, and a remote unit, the

Thermo-Hygrometer sensor.

The main unit has large read-outs for indoors temperature and

humidity, calendar clock, temperatures and relative humidity

collected and transmitted by the remote unit. The main unit can

support up to 3remote units.

The main unit is capable of keeping track of the maximum and

minimum recordings of different sites. And no wire installation is

required and the RMR132HG operates at 433MHz.

As for the calendar clock, it is radio-controlled. It automatically

synchronizes its current time and date when it is brought within an

approximate 1500km radius of the radio signal generated from

Frankfurt, Germany (DCF77).

You can also set the calendar clock manually when it is off range.

Other features include 4-language display, 4-step crescendo dual

alarms and interchangeable display modes.

MAIN FEATURES

RMR132HG_M_EN_R01 8/13/04, 12:30 PM1

TEMPERATURE & RELATIVE HUMIDITY ALARM :

K. [ ▲ ] BUTTON

Sets the readings for the upper or lower temperature and

humidity of individual channels

L. [HI/LO] BUTTON

- Set the upper or lower temperature alarm limits of

individual channels

- Confirms alarm settings

M. [AL ON/OFF] BUTTON

Enables or disables the alarms

CLOCK :

N. [ ▲] BUTTON

Advances the value of a setting

O. [AL ON/OFF] BUTTON

Enables or disables the alarms

P. [ ▼ ] BUTTON

Decreases the value of a setting

Q. [RESET] BUTTON

Returns all settings to default values

R. BATTERY COMPARTMENT

Accommodates two (2) UM-3 or "AA" size batteries

S. REMOVABLE TABLE STAND

For standing the main unit on a flat surface

A. THREE-LINE LCD DISPLAY

Facilitates easy reading of remote and indoors temperature-

humidity readings and calendar clock

B. [ ] BATTERY-LOW INDICATOR

Activates when the remote-sensor or main unit battery power

is low

C. [ ] RADIO-RECEPTION SIGNAL

Indicates the condition of radio reception

D. [IN/CHANNEL] BUTTON

Selects remote-sensor channels

E. [SET/MODE] BUTTON

Toggles between display modes and confirms entry while

setting the values for display

F. [24 hr OFF / ((•))] BUTTON

Sets the time for the alarms

G. [MEMORY] BUTTON

- Recalls the maximum or minmum temperature and humidity

readings

- Clears the maximum and minmum temperature and humidity

memory of remote sensor channels or the main unit display

H. [((1))] / [((2))] ALARM ICONS

Appears when the alarm time is displayed

I. [ ] / [ ] ALARM-ON ICONS

Appears when the alarm is activated

J. WALL-MOUNT HOLE

For mounting the unit on a wall

RMR132HG_M_EN_R01 8/13/04, 12:30 PM2

FEATURES: REMOTE

THERMO-HYGRO SENSOR

A. TWO-LINE LCD

Displays the current temperature and humidity monitored by

the remote unit

B. LED INDICATOR

Flashes when the remote unit transmits a reading

C. °C/°F SLIDE SWITCH

Selects between Centigrade (°C) and Fahrenheit (°F)

D. CHANNEL SLIDE SWITCH

Designates the remote unit Channel 1, Channel 2 or Channel 3

E. RESET

Returns all settings to default values

F. BATTERY COMPARTMENT

Accommodates two (2)AAA-size batteries

G. BATTERY DOOR

H. WALL-MOUNT HOLDER

Supports the remote unit in wall-mounting

I. REMOVABLE TABLE STAND

For standing the remote unit on a flat surface

BEFORE YOU BEGIN

For best operation,

1. Assign different channels to different remote units.

2. Insert batteries for remote units before doing so for the main

unit.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM3

4. Insert the batteries strictly according to the polarities shown

therein.

5. Replace the battery compartment door and secure its screws.

Replace the batteries when the low-battery indicator of the particular

channel lights up on the main unit. (Repeat the steps described in

section “BEFORE YOU BEGIN”)

Note that once a channel is assigned to a remote unit, you can only

change it by removing the batteries or resetting the unit.

BATTERY INSTALLATION: MAIN UNIT

1. Gently lift the tab on the battery compartment door.

2. Install 2 alkaline batteries (UM-3 or “AA” size 1.5V) strictly

according to the polarities shown.

3. Place the main unit as close as possible next to the remote unit,

reset the main unit after installing batteries. This will ensure

easier synchronization between the transmission and reception

of signals.

4. Position the remote unit and main unit within effective

transmission range, which, in usual circumstances, is 20 to 30

meters.

Note that the effective range is vastly affected by the building

materials and where the main and remote units are positioned. Try

various set-ups for best result.

Though the remote units are weather proof, they should be placed

away from direct sunlight, rain or snow.

BATTERY AND CHANNEL

INSTALLATION: REMOTE UNIT

The remote thermo-hygro sensor unit uses two (2) UM-4 or “AAA”

size alkaline batteries.

Follow these steps to install / replace batteries:

1. Remove the screws on the battery compartment.

2. Select the channel number on the CHANNEL slide switch.

3. Select the temperature display unit on the °C/°F slide switch.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM4

HOW TO USE THE TABLE STAND

OR WALL MOUNTING

The main unit has a removable table stand, which when connected,

can support the unit on a flat surface. Or you can remove the stand

and mount the unit on a wall using the recessed screw hole.

As for the remote unit, it comes with a wall-mount holder and a

removable stand. Use either to hold the unit in place.

Main unit

Wall-mount Table Stand

3. Replace the battery compartment door.

LOW BATTERY WARNING

When it is time to replace batteries, the respective low-battery

indicator will show up when the respective channel is selected.

The battery level of the main unit will be shown on the indoor

temperature window when it is running low.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM5

Remote unit

Wall-mount Table Stand

THE RESET BUTTON

This button is only used when the unit is operating in an unfavorable

way or malfunctioning. Use a blunt stylus to hold down the button.

All settings will return to their default values.

GETTING STARTED

Once batteries are placed in a given remote sensor unit, it will start

transmitting information at 40-second intervals.

Also, for approximately a 3-minute duration, the main unit will

automatically search for signals once batteries are installed. Upon

successful reception, the individual channel temperature reading

will be displayed on the top line and the respective humidity reading

on the bottom line. The main unit will automatically update its

readings at about 40-second intervals.

If no signals are received, blanks “ --- ” will be displayed and the

kinetic wave icon will not show.

To force a signal search:

´• Press and hold IN/CHANNEL &[MEMORY] for 2-seconds

to enforce a 3-minute search.

This is useful in synchronizing the transmission and reception of

the remote and main units.

Repeat this step whenever you find discrepancies between the

reading shown on the main unit and that on the respective remote

unit.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM6

HOW TO CHECK REMOTE AND INDOOR

TEMPERATURE & HUMIDITY

Display of readings from a remote sensor or the main unit is a 1-

step procedure. The remote sensor channel or the main unit display

is indicated in a box under the kinetic-wave icon.

To display temperature / humidity readings from the main unit:

• Press IN/CHANNEL until a dot is displayed in the box under

the kinetic-wave.

To display temperature / humidity readings from a remote

sensor:

• Press CHANNEL until the appropriate remote sensor channel

is displayed in the box under the kinetic-wave.

If no readings are received form one particular channel for more

than 15 minutes, blanks “ --- ” will be displayed until further

readings are successfully searched. Check the remote sensor to

ensure that it is secure and that the correct channel has been selected.

Optionally, press and hold IN/CHANNEL & [MEMORY] for 2-

seconds to enforce a search.

HOW TO READ THE

KINETIC WAVE DISPLAY

The kinetic wave display shows the signal receiving status of the

main unit. There are three possible forms:

THE COMFORT-LEVEL ICONS

The comfort level is based on the recorded relative humidity. An

indicator will be displayed or show if the level is comfortable, wet

or dry.

Kinetic-wave

Icon

Designated

Display

Indoor

Display

Remote

Display

Channel One

Remote

Display

Channel Two

Remote

Display

Channel Three

The unit is in searching mode.

Transmission data are securely

registered.

No signals.

Comfort-level

Comfort Dry Wet

RMR132HG_M_EN_R01 8/13/04, 12:30 PM7

REMOTE SENSOR SCANNING

The unit can be set to automatically scan and display readings from

the remote sensors and indoor readings. When the remote-sensor

mode is active, the display will show the readings from one channel

for about 4-seconds and then proceed to the next channel display.

To activate the remote-sensor scanning mode:

• Press and hold IN/CHANNEL for 2-seconds.

To deactivate the remote-sensor scanning mode:

• Press IN/CHANNEL, MEMORY,

[HI/LO], [▲], [ON/OFF]

(TEMP % RH AL)

MAXIMUM AND MINIMUM

TEMPERATURE AND HUMIDITY

The maximum and minimum recorded temperature and humidity

readings will automatically be stored in the memory.

To display the maximum and minimum display memory:

1. Select the channel to be checked.

2. Press MEMORY once to display the maximum temperature

and again the minimum temperature. The respective indicators,

MAX or MIN will be displayed.

TEMPERATURE AND

HUMIDITY TREND INDICATORS

The temperature-trend and humidity-trend indicators show the

trends of collected readings. Arrows indicate a rising, steady or

falling trend.

Note: If the temperature goes above or below the temperature

measuring range of the main unit or the remote unit ( stated in

specification), the display will show “HHH” or “LLL”.

Arrow

indicator

Temperature

Trend Rising Steady Falling

Rising Steady Falling

Arrow

indicator

Humidity

Trend

RMR132HG_M_EN_R01 8/13/04, 12:30 PM8

2. Press ▲to set the temperature or humidity limit. Each press

will increase increments by 1degree or percentage. Press and

hold the button for a rapid-scrolling sequence by increments

of 5.

Note:

The temperature range is from -50°C (-58°F) to +70°C (158°F).

If this is the first time you set the limits, the lower limit will start

from -50°C (-58°F) and the upper limit +70°C (158°F). Otherwise,

the reading will start from the temperature last selected.

The humidity range is from 2% to 98%.

If this is the first time you set the limits, the lower limit will start

from 2% and the upper limit 98% Otherwise, the reading will start

from the humidity last selected.

3. Repeat the steps to set the upper humidity setting and the lower

temperature and humidity settings.

4. When finished, press HI/LO to set another limit or wait 16-

seconds and the unit will automatically return to the normal

display. The respective HI, LO or both indicators will light up

to signify the status of the alarm.

If in another channel-1 other than channel one is selected, when the

alarm activates the display will switch to channel-1 and the display

will flash. If left untouched, the alarm will activate for 1-minute.

Press IN/CHANNEL, MEMORY,

[HI/LO], [▲], [ON/OFF]

(TEMP % RH AL)

to momentarily stop the alarm. The alarm will activate again if the

value continues exceeds the set limit.

To clear the memory:

•Press and hold MEMORY for 2-seconds.

If you press MEMORY now, the maximum and minimum

temperatures will have the same values as the current ones until

different readings are recorded.

HOW TO USE CHANNEL-1

TEMPERATURE/HUMIDITY ALARM

Upper and lower temperature and humidity limits for channel-1

can be set so that an alarm activates when the limits are exceeded.

The high and low temperature and humidity displays are selected

by sequentially pressing HI/LO.

The high-low displays are as follows:

Sequence Respective Display

Pressing HI/LO once Enters HI temperature display

Pressing HI/LO twice Enters HI humidity display

Pressing HI/LO third time

Enters LO temperature display

Pressing HI/LO fourth time Enters LO humidity display

To set a high or low temperature or humidity alarm:

1. Press HI/LO, channel-1 will be displayed.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM9

Note that when the temperature falls below freezing point, the

batteries of outdoor units will freeze, lowering their voltage supply

and the effective range.

3. The transmission is within range and path is clear of obstacles

and interference. Shorten the distance when necessary.

TRANSMISSION COLLISION

Signals from other household devices, such as door bells, home

security systems and entry controls, may interfere with those of

this product and cause temporarily reception failure. This is normal

and does not affect the general performance of the product. The

transmission and reception of temperature readings will resume

once the interference recedes.

CALENDAR CLOCK DISPLAY MODES

The RMR132HG supports four display modes in the sequence of:

MODE 1. Local Time

Hour, Minute Second

Day, Month

Note: If a second limit is passed while an alarm is active, the first

alarm will complete its 1-minute cycle and the alarm will continue

to activate for a second minute cycle to indicate that a second limit

has been surpassed.

To disable an alarm:

1. Enter the setting mode by pressing HI/LO.

2. Then, press AL ON/OFF.

The alarm has been disabled and will not sound at the previously

set limit.

To disable a sounding alarm:

•Press IN/CHANNEL, MEMORY,

[HI/LO], [▲], [ON/OFF]

(TEMP % RH AL)

the alarm sound will stop.

DISCONNECTED SIGNALS

If without obvious reasons the display for a particular channel goes

blank, press IN/CHANNEL & MEMORY to enforce an

immediate search.

If that fails, check:

1. The remote unit of that channel is still in place.

2. The batteries of both the remote unit and main unit. Replace as

necessary.

RMR132HG_M_EN_R01 8/13/04, 12:30 PM10

Autres manuels pour RMR132HG

Table des matières

Langues :

Autres manuels Oregon Scientific Horloge

Oregon Scientific

Oregon Scientific KD500 Manuel utilisateur

Oregon Scientific

Oregon Scientific BAR332ES Manuel utilisateur

Oregon Scientific

Oregon Scientific RM822 Manuel utilisateur

Oregon Scientific

Oregon Scientific BARM839 Manuel utilisateur

Oregon Scientific

Oregon Scientific RM313PA Manuel utilisateur

Oregon Scientific

Oregon Scientific RM622PA Manuel utilisateur

Oregon Scientific

Oregon Scientific RMR500ES Manuel utilisateur

Oregon Scientific

Oregon Scientific Glaze JW208 Manuel utilisateur

Oregon Scientific

Oregon Scientific JW108 Manuel utilisateur

Oregon Scientific

Oregon Scientific RGR682 Manuel utilisateur

Oregon Scientific

Oregon Scientific BAR339P Manuel utilisateur

Oregon Scientific

Oregon Scientific RA313P Manuel utilisateur

Oregon Scientific

Oregon Scientific RMR939P Manuel utilisateur

Oregon Scientific

Oregon Scientific EMR801 Manuel utilisateur

Oregon Scientific

Oregon Scientific DP100 Manuel utilisateur

Oregon Scientific

Oregon Scientific RM602 Manuel utilisateur

Oregon Scientific

Oregon Scientific TimeSphere RM382P Manuel utilisateur

Oregon Scientific

Oregon Scientific Jumbo JMR828A Manuel utilisateur

Oregon Scientific

Oregon Scientific JMR838WFA Manuel utilisateur

Oregon Scientific

Oregon Scientific RMR329P Manuel utilisateur

Oregon Scientific

Oregon Scientific RRM320P Manuel utilisateur

Oregon Scientific

Oregon Scientific RM818PA Manuel utilisateur

Oregon Scientific

Oregon Scientific RM932 Manuel utilisateur

Oregon Scientific

Oregon Scientific RAR186 Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur

LG LEC-005 Manuel utilisateur