Optoma HD83 Manuel utilisateur
SERVICE MANUAL
Prepared: Check: Approved:
Date Revise Version Description
2011.7.18 V1.0 Initial Issue
HD83
Copyright July. 2011. All Rights Reserved
Mina Amy
Condential i
HD83
Preface
This manual is applied to HD83 projection system.The manual gives you a brief
description of basic technical information to help in service and maintain the product.
Your customers will appreciate the quick response time when you immediately identify
problems that occur with our products. We expect your customers will appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background. Please
send the product back to the distributor for repairing and do not attempt to do anything
that is complex or not mentioned in the troubleshooting.
Notice:
The information found in this manual is subject to change without prior notice. Any
subsequent changes made to the data herein will be incorporated in future edition.
HD83 Service Manual
Copyright July, 2011.
All Rights Reserved
Manual Version 1.0
HD83 Condential II
Table of Content
Chapter 1 Introduction
Highlight 1-1
Compatible Mode 1-2Compatible Mode 1-21-2
Chapter 2 Disassembly Process
Equipment Needed & Product Overview 2-1
Disassemble Lamp Cover Module 2-2
Disassemble Lamp Module 2-2
Disassemble Bottom Cover Module 2-3
Disassemble Formatter Board Module 2-3
Disassemble Main Board and I/O Board Module 2-5
Disassemble Lens Ring Module 2-6
Disassemble Top Cover Module 2-7
Disassemble Top Shielding 2-7
Disassemble Right Cover Module 2-8
Disassemble Daughter Board Module 2-10
Disassemble System Fan Module 2-11
Disassemble Lamp Driver Module 2-13
Disassemble DMD and Lamp Blowers Module 2-14
Disassemble Air Duct Module 2-15
Disassemble LVPS Module 2-15
Disassemble Optical Engine Blower 2-18
Disassemble Left Cover Module 2-19
Disassemble Engine Module 2-20
Disassemble Color Wheel Module 2-20
Disassemble Lamp Blower Duct Module 2-22
Condential III
HD83
Disassemble DA Cover 2-22
Disassemble DA Motor Module 2-23Motor Module 2-23
Disassemble Rod Module 2-24
Disassemble Heat Sink Module 2-24
Disassemble DMD Module 2-25
Disassemble Focus Ring 2-25
Disassemble Zoom Ring 2-26
Disassemble Bottom Cover Shielding Module 2-26
Disassemble Ceiling Base Module 2-27
Rod Adjustment 2-28
Re-write Lamp Usage Hour 2-29
Chapter 3 Troubleshooting
LED Lighting Message For Projector 3-1
Main Procedure 3-2
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed 4-1
Test Condition 4-1
I/O Port Test 4-2
Run In Test 4-8
Test Inspection Procedure 4-9
ADC Calibration 4-10
DA Calibration 4-11
Restore Blower Speed 4-11
Chapter 5 Firmware Upgrade
Section 1: Pixelworks for FW Upgrade (USB) 5-1
HD83 Condential IV
Equipment Needed 5-1
Setup Procedure 5-2
Install USB Driver 5-2
Firmware Upgrade Procedure 5-4
Section 2: Pixelworks for FW Upgrade (RS232) 5-6
Equipment Needed 5-6
Firmware Upgrade Procedure 5-7
Section 3: 8051 FW Upgrade 5-9
Equipment Needed 5-9
8051 Firmware Upgrade Procedure 5-10
Check 8051 FW version 5-11
Chapter 6 EDID Upgrade
EDID Upgrade Procedure 6-1
Appendix A Exploded Image I
Appendix B
Serial Number Denition I
PCBA Code Denition II
HD83 Condential 1-1
Chapter 1
Introduction
1-1 Highlight
No Item Description
1Dimensions (WxDxH) ● 490x371.1x194 mm
2Power Supply ● Universal AC 100V-240V±10%, 50-60Hz
3Power Consumption
● Normal:TYP 360W MAX 375W @110/220VAC
● ECO : TYP 305W MAX 315W@110/220VAC
● Standby:ECO Mode (< 0.5 W)
4 Keystone correction ● Vertical +/- 5 degree (@1920 x 1080) (2D/3D)
5 Throw ratio ● 1.494 ~ 2.279(1080P)
6 Projection lens ● YM26
7 Lamp life
Normal Mode:
● 3000 Hours Standard @280W, 50% Survival Rate
ECO Mode:
● 4000 Hours Typical @230W, 50% Survival Rate
8Lamp ● 280W Lamp (Osram E20.8)
9DMD Chip&Number of
active dots
● 0.65” 1080P,
● Number of active dots: 1080P
10 Color wheel ● 6 segments (R64G62B54R64G62B54)
11 System controller ● TI DDP 3021
12 Video compatibility
● NTSC: M,3.58MHz,4.43MHz
● PAL: B, D, G, H, I, M, N,4.43MHz
● SECAM: B, D, G, K, K1, L,4.25/4.4MHz
● SDTV: 480i/p, 576i/p,
● HDTV: 720p(50/60Hz), 1080i(50/60Hz),1080p(24/50/
60Hz)
●3D Timing: HDMI1.4A/1.3
13 Input signal spec
● HDMIx2 (Version1.4A)
● YPbPrx1 ( 3 RCA )
● VGAx1 (D-Sub 15pin) for PC
14 Altitude&Temperature
● Operating: 0~2,500 ft 5°C~35°C
2,500~5,000 ft 5°C~30°C
5,000~10,000 ft 5°C~25°C
Condential 1-2
HD83
1-2 Compatible Mode
Computer Compatibility
Compatibility Resolution H-Sync [KHz] V-Sync [Hz] Digital Analog
PAL/SECAM 720 x 400 31.5 70 O O
720 x 400 37.9 85 O O
720 x 576 50 O O
VGA 640 x 480 31.5 60 O O
640 x 480 67 O O
640 x 480 37.9 72.8 O O
640 x 480 37.5 75 O O
640 x 480 43.3 85 O O
SVGA 800 x 600 35.2 56.3 O O
800 x 600 37.9 60.3 O O
800 x 600 46.9 75 O O
800 x 600 48.1 72.2 O O
800 x 600 53.7 85.1 O O
XGA 1024 x 768 48.4 60 O O
1024 x 768 56.5 70.1 O O
1024 x 768 60 75 O O
1024 x 768 68.7 85 O O
HD720 1280 x 720 50 O O
1280 x 720 60 O O
1280 x 720 92.62 120 O O
WXGA 1280 x 768 47.4 60 O O
1280 x 768 75 O O
1280 x 768 85 O O
WXGA-800 1280 x 800 60 O O
SXGA 1280 x 1024 64 60 O O
1280 x 1024 80 75 O O
SXGA+ 1400 x 1050 60 O O
Condential 1-3
HD83
Compatibility Resolution H-Sync [KHz] V-Sync [Hz] Digital Analog
UXGA 1600 x1200 75 60 O O
HD1080 1920 x 1080 24 O O
1920 x 1080 50 O O
1920 x 1080 60 O O
WUXGA 1920 x 1200 60 O O
HDTV 1920 x 1080i 50 O O
1920 x 1080i 60 O O
1920 x 1080p 24 O O
1920 x 1080p 50 O O
1920 x 1080p 60 O O
1280 x 720 45 60 - -
1280 x 720p 50 O O
1280 x 720p 60 O O
SDTV 720 x 576 31.3 50 - -
720 x 576i 50 O O
720 x 576p 50 O O
720 x 480 31.5 60 - -
720 x 480i 60 O O
720 x 480p 60 O O
Note: 1.“O ” expressed support this type of signal and “-” expressed that does
not support this type of signal.
2. If the Computer Compatibility supportive signal is different from
User’s Manual, please refer to User’s Manual.
Condential 2-1
HD83
Chapter 2
Disassembly Process
2-1 Equipment Needed & Product Overview
1. Screw Bit (+) :105
2. Screw Bit (+) :107
3. Screw Bit (-) :107
4. Hex Sleeves 5 mm
5. Tweezers
6. HD83 unit
* Before you start: This process is protective level II. Operators should wear electrostatic chains.
* Note: If you need to replace the main board, you have to record the lamp usage hour.
Condential 2-2
HD83
2-2-2 Disassemble Lamp
Module
1. Unscrew 2 screws (as red circle) on the
lamp module.
2. Take off lamp module from the projector.
2-2-1 Disassemble Lamp
Cover Module
1. Turn the projector backside.
2. Push the lamp cover switch to the
open state (as the red oval-shaped
circle).
3. Disassemble lamp cover module.
Autres manuels pour HD83
3
Table des matières
Autres manuels Optoma Projecteur
Optoma
Optoma H79 Manuel utilisateur
Optoma
Optoma TX1080 Manuel utilisateur
Optoma
Optoma X400LVe Manuel utilisateur
Optoma
Optoma TX7155 Manuel utilisateur
Optoma
Optoma ZW300USTe Manuel utilisateur
Optoma
Optoma HD91 Manuel technique
Optoma
Optoma H79 Manuel utilisateur
Optoma
Optoma W402 Manuel utilisateur
Optoma
Optoma ML1000 Manuel utilisateur
Optoma
Optoma HD8000-LV Manuel utilisateur
Optoma
Optoma X501 Manuel utilisateur
Optoma
Optoma DW318 Manuel
Optoma
Optoma ZH406 Manuel utilisateur
Optoma
Optoma L1 Manuel utilisateur
Optoma
Optoma EP739 Manuel utilisateur
Optoma
Optoma GT1080e Manuel utilisateur
Optoma
Optoma EH416e Manuel utilisateur
Optoma
Optoma HD200X Manuel utilisateur
Optoma
Optoma ML750ST Manuel utilisateur
Optoma
Optoma PRO360W Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
