Optika B-190 Manuel utilisateur

MICROSCOPES

ITALY

OPTIKA

MICROSCOPES - ITALY

www.optikamicroscopes.com - [email protected]

Ver. 1.1.0

PERATI

N MANUA

GUIDA UTENTE

ANUAL DE INSTRUCCIONES

BEDIENUNGSANLEITUNG

Ryf AG

Bettlachstrasse 2

2540 Grenchen

tel 032 654 21 00

fax 032 654 21 09

www.ryfag.ch

Page 2

INDEX

1.0 DESCRIPTION page 3

2.0 INTRODUCTION page 5

3.0 UNPACKING AND ASSEMBLY page 5

4.0 USING THE MICROSCOPE page 5

5.0 MAINTENANCE page 7

6.0 TECHNICAL SPECIFICATIONS page 8

7.0 RECOVERY AND RECYCLING page 9

Page 3

1.0 DESCRIPTION

EYEPIECE

DIOPTRIC ADJUSTMENT

RING

BINOCULAR OBSER-

VATION HEAD

[B-192]

OBJECTIVE

SLIDE CLAMP

COARSE FOCUSING

KNOB

FINE FOCUSING

KNOB

BRIGHTNESS ADJUSTMENT

KNOB

LED

ILLUMINATOR

TENSION ADJUSTMENT

KNOB

IRIS

DIAPHRAGM

TRANSLATION

KNOBS

CONDENSER

STAGE

NOSEPIECE

Page 4

1.0 DESCRIPTION

MONOCULAR OBSERVATION

HEAD [B-191]

TENSION

ADJUSTMENT KNOB

ON/OFF SWITCH POWER SUPPLY

INPUT JACK

REAR:

Page 5

2.0 INTRODUCTION

This microscope is a scientific precision instrument designed to last for many years with a minimum

of maintenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and

that it must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this ma-

nual.

3.1 The microscope is housed in a moulded Styrofoam container. Remove the tape from the

edge of the container and lift the top half of the container. Take some care to avoid that the

optical items (objectives and eyepieces) fall out and get damaged. Using both hands (one

around the arm and one around the base), lift the microscope from the container and put it on

a stable desk.

3.2 Place the observation head onto the top of the arm and tighten the lock-screw. Insert the

eyepieces into the eye tubes.

3.3 Connect the provided 7,5Vdc power supply to the power supply input jack on the rear of the

microscope.

4.1 Adjust the observation head

Loosen the lock-screw, turn the observation head to a comfortable position for observation,

and then lock the lock-screw.

4.2 Place the specimen on the stage

Lock the specimen slide on the mechanical stage using the slide clamp. Ensure that the spe-

cimen is centred over the stage opening by adjusting the coaxial knobs of the stage.

4.3 Lamp settings

The microscope is fitted with power white LED illuminator. Before turning on the light, read

the section 5.3 about electrical safety precautions. Insert the plug of the 7,5Vdc power supply

into the jack on the rear and turn on the ON/OFF switch. Turn the brightness adjustment knob

to a brightness suitable for observation.

4.4 Adjust interpupillary distance

Hold the right and left parts of the observation head by both hands and adjust the interpupil-

lary distance by turning the two parts until one circle of light can be seen.

3.0 UNPACKING AND ASSEMBLY

4.0 USING THE MICROSCOPE

Page 6

4.0 USING THE MICROSCOPE

4.5 Focus and diopter adjustment

Rotate the coarse focusing knob to bring the slide into focus using an objective with a low

magnification. Adjust the fine focusing knob to get the image sharp and clear while observing

with your right eye, then turn the dioptric adjustment ring on the left eyepiece until a sharp

and clear image can be observed also with the other eye. Turn the tension-adjust-knob to

get a suitable tension for the focus system. When the image is in focus, turn the nosepiece to

choose the objective you need.

4.6 Condenser adjustment

Hold the notched ring at the base of the condenser and rotate it up or down until you reach a

clear and uniform sample illumination.

4.7 Set the numerical aperture

Adjust the aperture of the iris diaphragm to set the numerical aperture of the illuminator, thus

controlling image contrast and resolution.

4.8 Additional filters

The green glass filter can be inserted in the flip-out filter holder underneath the condenser.

HOLD THIS

NOTCHED RING

AND ROTATE IT

Page 7

5.1 Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with

a temperature of 0-40°C and a maximum relative humidity of 85 % (non condensing). Use a

dehumidifier if needed.

5.2 To think about when and after using the microscope

• The microscope should always be kept vertically when moving it and be careful so that no

moving parts, such as the eyepieces, fall out.

• Never mishandle or impose unnecessary force on the microscope.

• Never attempt to service the microscope yourself.

• After use, turn off the light immediately, cover the microscope with the included dust-cover,

and keep it in a dry and clean place.

5.3 Electrical safety precautions

• Before plugging in the power supply, make sure that the supplying voltage of your region

matches with the operation voltage of the equipment and that the lamp switch is in off-

position.

• Users should observe all safety regulations of the region. The equipment has acquired the CE

safety label. However, users do have full responsibility to use this equipment safely.

5.4 Cleaning the optics

• If the optical parts need to be cleaned try first to: use compressed air.

• If that is not sufficient: use a soft lint-free piece of cloth with water and a mild detergent.

• And as a final option: use the piece of cloth moistened with a 3:7 mixture of ethanol and

ether.

Note: ethanol and ether are highly flammable liquids. Do not use them near a heat source,

near sparks or near electric equipment. Use these chemicals in a well ventilated room.

• Remember to never wipe the surface of any optical items with your hands. Fingerprints can

damage the optics.

• Do not disassemble objectives or eyepieces in attempt to clean them.

5.5 If you need to send the microscope to Optika for maintenance, please use the original

packaging.

5.0 MAINTENANCE

Page 8

HEAD: B-191: monocular, 360° rotating, 30° inclined

B-192: binocular, 360° rotating, 30° inclined

EYEPIECES: WF 10X/ 18mm

NOSEPIECE: Quadruple, reversed

OBJECTIVES: Achromatic 4x, 10x, 40x, 100x (oil immersion)

WORKING STAGE: Double layer with mechanical sliding stage, 125x115mm, moving range

50x30mm

CONDENSER: 1.25 N.A. Abbe type, with iris diaphragm

FOCUSING SYSTEM: Coaxial coarse and fine focusing system, with tension adjustment mechanism

ILLUMINATION: Extra-power White LED, non-rechargeable, with brightness control.

MAINS POWER: Input Voltage of the power supply:

100-240Vac / 50-60Hz

6.0 TECHNICAL SPECIFICATIONS

Page 9

The appliance reports the symbol:

This symbol means that the appliance can be a precious source of raw materials. Therefore, it must

not be disposed of as waste, but separately collected for the recycling and the recovery of the mate-

rials it contained in it. Such materials, if improperly dispersed into the environment, can be harmful

to the environment and to human health.

The producer of the equipment, Optika Microscopes, recovers, re-uses and recycles the raw mate-

rials contained in the equipment. Such recovery, however, needs your help.

When, at the end of its operating life, you shall decide to dispose of the apparatus, do not try to open

it, nor to use parts of it in ways other than reported in this Manual, but bring it back to the Distributor

you bought it from, or to other Optika Microscopes distributors. The Distributor shall collect the ap-

paratus free of charge.

The recovery of the raw materials shall then take place in accordance with the European Directive

2002 / 96 / EC and all other relevant Directives. Never disassemble, nor dispose of as waste, appa-

ratus reporting the “crossed bin” symbol indicated above.

7.0 RECOVERY AND RECYCLING

Pagina 10

INDICE

1.0 DESCRIZIONE page 11

2.0 INTRODUZIONE page 13

3.0 DISIMBALLAGGIO E MONTAGGIO page 13

4.0 UTILIZZO DEL MICROSCOPIO page 13

5.0 MANUTENZIONE page 15

6.0 SPECIFICHE TECNICHE page 16

7.0 MISURE ECOLOGICHE page 17

Autres manuels pour B-190

Table des matières

Langues :

Autres manuels Optika Microscope

Optika

Optika B-510 Series Manuel utilisateur

Optika

Optika B-190 Manuel utilisateur

Optika

Optika B-500DK Manuel utilisateur

Optika

Optika B-380 Series Manuel utilisateur

Optika

Optika B-600 Manuel d'installation

Optika

Optika OPTIStar OS-SZ1 Manuel utilisateur

Optika

Optika LAB-1 Manuel utilisateur

Optika

Optika IM Series Manuel utilisateur

Optika

Optika B-1000FL HBO Manuel utilisateur

Optika

Optika B-500BSp Manuel utilisateur

Optika

Optika B-1000 MET Manuel utilisateur

Optika

Optika XC-100L Manuel utilisateur

Optika

Optika B-510 Series Manuel utilisateur

Optika

Optika B-150POL-M Manuel utilisateur

Optika

Optika B-1000Ti-2 Manuel utilisateur

Optika

Optika B-500TiFL Manuel utilisateur

Optika

Optika B-500Ti-2 Manuel utilisateur

Optika

Optika XDS-3 Manuel utilisateur

Optika

Optika IM Series Manuel utilisateur

Optika

Optika B-510 Series Manuel utilisateur

Optika

Optika SZM Manuel utilisateur

Optika

Optika ECOVISION Series Manuel utilisateur

Optika

Optika B-50 Manuel utilisateur

Optika

Optika B-800 Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur