Opticon OPL-9725 Guide de l'utilisateur

OPL-9725

Demo Application Manual

Version LFBP0033

OPL 9725 Demo Application

Getting Started

The OPL 9725 is shipped with a demo application loaded on the scanner and ready to use out of the

box. The demo application allows you to collect data and transfer data to your host PC. Data is saved

in the OPL’s RAM disk as a flat text file called SCAN.TXT. The file then can be transferred to your PC

using the NetO32 application which can be installed from the Opticon OPL Product CD supplied with

your OPL. You can also transfer the file to your PC in plain ASCII mode using a terminal application

like HyperTerminal.

NetO protocol is the default communication mode but you can switch to ASCII mode by scanning a

special barcode. Please see the section Switching File Transfer Mode at the end of this document.

Steps to use the demo application:

1. Scan some barcodes using the trigger button on the OPL 9725. The OPL will beep once and the

LED will flash green after each successful scan.

2. Once you are done collecting data, you can send the data file to your PC using NetO32 application.

Note: You must first install and configure NetO32 before you can transfer your data. For

information on installing and configuring NetO32, please refer to the NetO32 Instruction

Manual which can be found on the OPL Product CD supplied with your OPL.

3. Configuring NetO:

a. Set the baud rate to 115200bps (default). If you change the default baud rate, you need to

change the switches on the cradle to match the new baud rate. See the OPL/CRD manual for

details.

b. Set the COM port to match the COM port number to which the CRD 9723 cradle is connected

to on your PC

c. Configure your download folder. This is the folder in which NetO will save your data file after

downloading.

d. Configure the File Download mode (options are Append, Overwrite and Unique). Please refer

to NetO’s Instruction Manual for details on each of these modes.

Version LFBP0033 Page 2

OPL 9725 Demo Application

4. Downloading your data file:

a. Make sure the cradle is connected to a COM port on your PC and is powered on.

b. Place the OPL on cradle

c. Start NetO Protocol by selecting Protocol

Start

from the Menu. When Neto protocol is running, the

amber light on the cradle will be blinking. You should

see the file download progress on NetO’s main screen.

The file SCAN.TXT should now be available in the

download folder you configured in step 3.c above.

d. The file is deleted from the OPL after download.

Data Format

Data is formatted as comma delimited variable length fields in the file with each record on a separate

line as follows:

Example:

070330506060,03/22/2007,14:17:47

070330506060,03/22/2007,14:17:48

070330506060,03/22/2007,14:17:49

Version LFBP0033 Page 3

OPL 9725 Demo Application

Version LFBP0033 Page 4

Switching File Transfer Mode

The default data transfer mode is NetO. You can switch between NetO and plain ASCII modes by

scanning the corresponding barcode from the table below.

When using plain ASCII mode, the file is transferred automatically to the PC when the OPL is placed

on the cradle. The file is deleted after transmission. You need to use your own terminal application

like HyperTerminal to receive the data.

If you’re using HyperTerminal, you can configure it to capture data in a file using the menu option

Transfer ÆCapture Text. Please refer to HyperTerminal help for details.

It is a good idea to test your unit using simulated data after making any setting changes before

collecting real data.

+008+ PLAIN ASCII ,119, 

+009+ NETO ,11:, 

CAUTION:

When using Plain ASCII mode, Do not place the OPL on the cradle until the host computer

program is running and ready to receive data.

Table des matières

Autres manuels Opticon Lecteur de codes-barres

Opticon

Opticon 25-WEDGE-06 Manuel utilisateur

Opticon

Opticon C 37 Manuel utilisateur

Opticon

Opticon OPI-3601 Manuel utilisateur

Opticon

Opticon OPN2002 Guide de l'utilisateur

Opticon

Opticon OPR 2001 Manuel utilisateur

Opticon

Opticon LH2 Manuel utilisateur

Opticon

Opticon OPN2002 Instructions d'utilisation

Opticon

Opticon OPI 2002 Manuel utilisateur

Opticon

Opticon NFT 2200 Manuel utilisateur

Opticon

Opticon Code Reader 2.0 Manuel utilisateur

Opticon

Opticon NFT 1125 Series Manuel utilisateur

Opticon

Opticon OPL 2724 ZAPPER Manuel de l'opérateur

Opticon

Opticon NLB-1000 Manuel utilisateur

Opticon

Opticon RFI3793B Manuel utilisateur

Opticon

Opticon PX-35 Manuel utilisateur

Opticon

Opticon NFT 1125 Series Manuel utilisateur

Opticon

Opticon OPN-3102i Manuel utilisateur

Opticon

Opticon IRU 4100 Manuel utilisateur

Opticon

Opticon OPR 3001 Manuel utilisateur

Opticon

Opticon PX-25 Manuel utilisateur

Opticon

Opticon OPN-2006 BLUETOOTH Manuel de programmation

Opticon

Opticon OPL 2724 ZAPPER Manuel utilisateur

Opticon

Opticon OPR 3201 Manuel utilisateur

Opticon

Opticon N LB 9625 Series Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur