OPTICLIMATE REVOMAX II Manuel d'utilisation
BY OPTICLIMATE
Engineered & Designed in Holland
www.opticlimate.com
INSTALLATION
& USER GUIDE
opticlimate.com
THE FUTURE OF COOLING
JUST GOT COOLER.
II
PLEASE READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THE UNIT:
High Temperature Safeguard on page 7
Delete alarm history on page 12
Dehumidify without cooling pro4 on page 12
INSTALLATION
Installation
Installation spacing
To guarantee proper air suction, leave at least 15cm of space between the wall and the backside of the unit, where the carbon & dust
filters and air inlet are located. At least 15cm of space should also be left between the topside of the unit and the ceiling. Larger spaces
are preferred. The unit must stand free from the wall to avoid contact noises.
15cm
15cm
Installation
The unit can be hung from a ceiling or placed on a stand or frame.
Ceiling
To hang the unit from a ceiling, remove both side panels and pinch a hole through the insulation at the position of the 4 holes in the
bottom of the unit. Use an M8 or M10 metal threaded rod with a nut, washer and rubber damper to prevent unwanted noise or
vibration.
2
EN
blank
INSTALLATION
Stand or frame
Make or buy a stand or frame to hold the weight of the Opticlimate. (see nameplate )
You can use the rubber damper or a vibration damper (not incuded)
Pinch a hole through the insulation at the position of the 4 holes in the bottom of the unit. Use an M8 bolt and washer to mount the
rubber or damper.
Make sure the side of the condensation outlet is 1 cm lower than the opposite side.
Routing the Cables
First, the panel at the left side near the manometer should be removed to make the various electrical connections.
A magnetic valve, water leakage sensor, automatic moisture meter, remote control and room
temperature sensor are supplied with the unit. Their cables can be led to the outside through the opening at the bottom of the panel.
The power cable for the power supply can be led through the black feed-through rubber at the side of the unit.
3
EN
blank
humidity sensor, light sensor,
temperature sensor, electric solenoid
valve cable, water leak sensor, remote
control cable, Ethernet cable.
Power cord
ELECTRICAL CONNECTION
Humidity Sensor /
Light sensor
Electric
Watervalve
Compressor Start Sensor
(Only water Cooler)
Smart Remote Controller
RS485 Water Leak Sensor
Room Temperature
Sensor
Automatic Humidity Sensor with light cell
The Automatic Humidity Sensor with light cell supplied with the unit can be found in the connection set supplied with Revomax. The cable
should be led through the opening in the front panel and connected to the circuit board (see picture) The sensor should be hung in the room
and may not be covered. The light cell determents if it's night or day.
Room temperature sensor
The connection set also contains a room temperature sensor, which needs to be connected to the printed circuit-board. This sensor should
be led to the outside through the opening in the panel and should be hung at the level of the upper side of the vegetation. The sensor should
be protected against heat radiation and must be put in the shade. A protective cover over the sensor is sufficient.
The Smart Remote Controller
The smart remote controller can be found in a separate black box, the cable to connect the smart remote controller can be found in the
connection set. The cable must be led through the opening in the panel and the UTP connector must be connected to the circuit board (see
picture) The USB side of the cable can be plugged in one of the USB ports on the smart remote controller.
Power supply specifications
4 different OptiClimate models are available. For your safety and the safety of the OptiClimate, the following specifcations should
be observed when connecting the power supply: use the circuit breakers (MCB) and cable thickness specifed.
The cables for the supply voltage should be led through the grommet at the side of the unit and connected to the green screw terminal
on the circuitboard as described in the illustration. The grounding can be connected to the PE at the bottom right of the metal back plate.
When it's not possible to use a 3 phase power supply but only a single phase power supply is available the phase L1 + L2 + L3 need to be looped using
a correct diameter wire. (only 6000 and 10000 models)
4
EN
blank
WATER CONNECTIONS
Water-in and water-out connections of the cooling water.
The unit can be used by connecting the water in and out connections to a cold water supply and a drain or can be used using
the Opticlimate water cooler to cool the water in a closed loop. (connections and discription of a water cooler setup need to be
obtained in the water cooler manual. Only the setup using a cold water supply and a drain are discribed in this manual.
Using a water cooler or other closed loop systems skip to page *
The unit has a water inlet and outlet. The inlet needs to be connected to a cold water supply (max 25°C) with a solenoid valve
installed at the beginning of the piping going to the Opticlimate water-in connection. In case of a waterleak the valve will close.
Mounting the valve at the end of the piping (near the Opticlimate) is pointless. (always check the flow direction arrow on the valve!).
Make sure that the black magnetic coil of the solenoid valve is positioned upwards (preferred) or to the side. If it is positioned
downwards, condensate from the cold valve might enter the coil. Make sure that the solenoid valve is installed at a fxed point that is
always easily accessible to the user.
To the rest
of the building Strainer
Electric water
valve
To drain
Main stop tap& water meter
Cold water supply
A strainer should be placed in the water inlet. This strainer prevents blockage in the heat exchanger inside the unit. It is recommended
to insulate the cold water supply line in order to prevent condensation build-up. The upper water connection is the water-outlet. The
water-outlet can be connected directly to the drain (sewer). Alternatively, the warm water can be used for heating purposes. The
water is aprox 35°C- 40°C.
The water flow (water usage) is automatic regulated by an electronic flow regulator inside the unit.
When you use and alternative cold water supply such as a well or water from a river , leak or pond, make sure the water is filtered
and clean the heat exchanger on regulare base. Contact tech support for more information regarding cleaning the heat exchanger.
5
EN
blank
CONDENSATION WATER
Discharge of the condensation water
The unit will dehumidify the air during cooling and in dehumidify mode. The moisture extracted from the air is collected in the condensation
pan. The condensation pan has an ¾ drain pipe where the condensate will run off. The condensate can be used as irrigation water.
The cooling block has been modified to prevent metals or oxides from entering the condensate water.
The location of the drain pan is on the negative pressure side of the unit, meaning that air can enter into the unit through the condensation
drain, It's highly recommended to use a “P-trap” on the condensation outlet to prevent air entering the unit and to prevent condensate
run-off problems. Not using a p trap also results in loss of capacity and bypassing non processed air.
Cap for cleaning
Drain
Opticlimate drain pan
Condensation drain connection Correct drain installation
If the unit is installed at the same level or lower than the drain or sewer, a condensation lift pump can collect the water. This small
lift pump pumps the water through a hose of 9mm to a height of 4 metres into the drain or collecting tank. Stronger pumps are also
available.
6
EN
blank
SMART REMOTE CONTROLLER
Connecting the Smart Remote Controller
Power
Connect the power supply and USB connector from the remote cable to the Smart Remote controller.
USB to
connect remote
Power supply
from adapter
HDMI to connect
monitor (view only)
Ethernet
Power
Connect the power supply and USB connector from the remote cable to the Smart Remote controller.
7
EN
blank
CONNECTIONG THE SMART REMOTE CONTROLLER
Humidity Sensor /
Light sensor
Electric
Watervalve
Compressor Start Sensor
(Only water Cooler)
Smart Remote Controller
RS485
Water Leak Sensor
Room Temperature
Sensor
Connect the RJ45 side of the remote control cable to the RJ45 plug at the left upper corner of the circuit board (see image)
Powering up the unit
- Power on the Smart Remote Controller
- Power on the Opticlimate by switching on the power supply.
- Open the water supply.
After powering up the Opticlimate, the unit will first initialize, this can take a few minutes.
All valves and sensor are tested prior to startup. The remote controller cannot be operated during initializing of the Opticlimate.
After powering up the Smart remote controller, the remote will first initialize, this can take a few minutes. You will see several screens
pop-up and close again, this is normal.
The unit is now installed and ready to use
8
EN
blank
OPERATING BY USING THE SMART REMOTE CONTROLLER
After both Smart controller and Opticlimate are initialised, the Smart Remote controller will display the Home screen *1
Alarm
The ALARM icon will display an alarm (power failure)
this is normal after startup and will show each time you
power up the unit or in the case of a power failure.during
initializing of the Opticlimate. After powering up the
Smart remote controller, the remote will first initialize, this
can take a few minutes. You will see several screens pop-
up and close again, this is normal.
Reading and deleting the alarm
You can obtain more information regarding this alarm by
pushing on the “enlarge button”.
You can erase the alarm by pushing on the alarm icon and
then press the bin.
In the right upper corner you find the home icon you can toggle between home 1 (basic) and home 2 (advanced)
Homescreen 1
You can obtain more information regarding this alarm by pushing
on the “enlarge button”.
Homescreen 2
You can obtain more information regarding this alarm by pushing
on the “enlarge button”.
9
EN
blank
OPERATING BY USING THE SMART REMOTE CONTROLLER
Setting the basic parameters
Go to home 1 or home 2 by pressing the home icon.
Touch the Temperature area to enlarge the window for
temperature day/night settings.
Setting day temperature setpoint.
Touch the sun icon to set daymode temperature and use
+ and – to change the daymode temperature.
Setting night temperature setpoint.
Touch the moon icon to set nightmode temperature and
use + and – to change the nightmode temperature.
Touch the X to return to home.
10
EN
blank
Table des matières
Autres manuels OPTICLIMATE Système de contrôle
