Onnto USB 2.0 2-Bay RAID System Manuel utilisateur
2-bay
R
AI
D
Systems
for 3.5 ” SATA HDD
Easy RAID Storage Management for High Productivity
USB2.0
eSATA/USB2.0
USB2.0/FireWire800
User’s Manual
Rev. 06
This User’s Manual provides instructions
on assembly and usage of the 3 models
Rev. 07
2
Table of Contents
GENERAL INFORMATION 4
COPYRIGHT 4
NOTICES AND CLASSIFICATIONS 4
CONTACT US 4
INTRODUCTION 5
FEATURES 5
PRECAUTIONS FOR THE RAID SYSTEM 6
USB 2.0 2-BAY RAID SYSTEM 7
SYSTEM REQUIREMENTS 7
PACKAGE CONTENTS 7
USB 2.0 2-BAY RAID SYSTEM VIEWS 8
FRONT VIEW 6
REAR VIEW 6
INSTALLING/REPLACING THE HARD DRIVES IN THE RAID SYSTEM 9
SETTING THE RAID MODE 13
CONNECTING THE RAID SYSTEM TO A COMPUTER 15
SAFE REMOVAL OF THE RAID SYSTEM 17
LED INDICATORS 17
SYSTEM LED x 1 17
HDD LED x 2 17
REBUILD 18
ONLINE REBUILD 18
REBUILD EXISTING DATA TO A BACKUP HDD 18
HOT SWAP 19
EXTERNAL BOOTUP 19
eSATA/USB 2.0 2-BAY RAID SYSTEM 20
SYSTEM REQUIREMENTS 20
PACKAGE CONTENTS 20
eSATA/USB 2.0 2-BAY RAID SYSTEM VIEWS 21
FRONT VIEW 19
REAR VIEW 19
INSTALLING/REPLACING THE HARD DRIVES IN THE RAID SYSTEM 22
SETTING THE RAID MODE 26
CONNECTING THE RAID SYSTEM TO A COMPUTER 27
SAFE REMOVAL OF THE RAID SYSTEM 29
LED INDICATORS 29
SYSTEM LED x 1 29
HDD LED x 2 29
REBUILD 30
ONLINE REBUILD 30
REBUILD EXISTING DATA TO A BACKUP HDD 30
HOT SWAP 31
EXTERNAL BOOTUP 31
eSATA PCI EXPRESS CARD INSTALLATION 32
SYSTEM REQUIREMENTS 32
3
HARDWARE INSTALLATION 32
DRIVER INSTALLATION 33
VERIFY DRIVER INSTALLATION 33
USB 2.0/FIREWIRE 800 2-BAY RAID SYSTEM 35
SYSTEM REQUIREMENTS 35
PACKAGE CONTENTS 35
USB 2.0/FIREWIRE 800 2-BAY RAID SYSTEM VIEWS 36
FRONT VIEW 34
REAR VIEW 34
INSTALLING/REPLACING THE HARD DRIVES IN THE RAID SYSTEM 37
SETTING THE RAID MODE 41
CONNECTING THE RAID SYSTEM TO A COMPUTER 43
SAFE REMOVAL OF THE RAID SYSTEM 45
LED INDICATORS 45
SYSTEM LED x 1 45
HDD LED x 2 45
REBUILD 46
ONLINE REBUILD 46
OFFLINE REBUILD 46
REBUILD EXISTING DATA TO A BACKUP HDD 46
HOT SWAP 47
EXTERNAL BOOTUP 47
RAID SYSTEM and MODES 48
JBOD 48
SPANNING 48
STRIPING 49
MIRRORING 50
APPENDIX: SPECIFICATIONS 51
4
GENERAL INFORMATION
COPYRIGHT
Copyright @ 2008 ONNTO Corporation. All rights reserved. No part of this
publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording or
otherwise, without the prior written consent of ONNTO Corporation.
The product information provided in this manual is subject to change without prior
notice and does not represent a commitment on behalf of the vendor. The vendor
assumes no liability or responsibility for any errors that may appear in this manual.
NOTICES AND CLASSIFICATIONS
FCC-B Radio Frequency Interference Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
CONTACT US
We are committed to offer economical, high-quality connectivity and storage
enclosure solutions to the market. Your questions, inquiries or comments are
welcomed.
For Technical Support, please go to our website at www.onnto.com.tw
ONNTO Corporation
3F, No. 60, Lane 321, Yang Guang St.,
Nei Hu, Taipei 114 Taiwan
Tel: +886-2-8797-8868
Fax: +886-2-8797-4801
Email: [email protected]
5
INTRODUCTION
Thank you for purchasing the 3.5” SATA HDD 2-bay RAID System. The 2-bay
RAID System provides massive storage capacity and advanced RAID
configuration options in a desktop storage device. The Mode switches allow
easy configuration of Striping (RAID 0), Spanning, Mirroring (RAID 1) and JBOD
RAID Modes.
FEATURES
Provides Striping, Spanning, Mirroring, and JBOD RAID Modes for effective
storage management
Supports easy RAID Mode configuration with convenient Mode switches
Offers easy monitoring of system status via LED indicators
Dissipates heat efficiently with aluminum housing
Maximizes airflow and product life with a silent, durable fan
Increases data transfer speed with the Serial ATA technology
Supports hot-plug and HDD hot-swap
Enables flexible eSATA, USB 2.0 or 1394b connectivity
Any loss, corruption, or destruction of data is the sole responsibility of the
user of the RAID System. Under no circumstances will the manufacturer be held
liable for the recovery or restoration of any data.
This User’s Manual provides instructions on assembly and usage of the following
products:
USB 2.0 2-bay RAID System
eSATA/USB 2.0 2-bay RAID System
USB 2.0/FireWire 800 2-bay RAID System
Please thoroughly read and follow the instructions provided in this manual.
Failure to do so may result in damage to the RAID System, and any or all of the
connected devices.
6
PRECAUTIONS FOR THE RAID SYSTEM
♦The main circuit board of the RAID System is susceptible to static
electricity. Proper grounding is required to prevent electrical damage to
the RAID System or other connected devices, including the computer host.
Always place the RAID System on a smooth surface and avoid all
dramatic movement, vibration and percussion.
♦Do NOT allow water to enter the RAID System.
♦Installation of additional equipment in the host computer may be required.
Visit our website to download the latest product information updates.
♦Do NOT attempt to service this unit yourself. Opening or removing the
back cover will expose you to dangerous voltages or other hazards.
♦Do NOT block the front and rear ventilation. Proper airflow is required to
ensure reliable operation and to prevent overheating.
♦Do unplug the RAID System from the electrical outlet when not in use to
provide an ecological friendly environment.
♦Use only the power supply cable provided with the RAID System.
7
USB 2.0 2-BAY RAID SYSTEM
SYSTEM REQUIREMENTS
PC
266MHz or faster CPU (Microsoft Vista requires a minimum 800MHz CPU)
64MB of RAM (Microsoft Vista requires a minimum 512MB of RAM)
Microsoft Windows 2000, XP, 2003, or Vista
One available USB 2.0 port
MAC
PowerPC or Intel Core Duo processor
64MB of RAM (Mac OS X 10.4 requires 256MB of RAM)
Mac OS 10.2 or higher (PowerPC) or Mac OS X 10.4 (Intel)
One available USB 2.0 port
SATA compatible hard drive is required for the RAID System. Once the
HDDs are formatted, the actual available storage capacity can vary depending on
selected operating environment (normally 5-10 % less).
PACKAGE CONTENTS
2-bay RAID System
USB Type A to mini-B Cable
AC Adapter
Fastening Screws x 8
Quick Start Guide
USB Cable Fastening ScrewAC AdapterRAID System Quick Start Guide
Please keep all package contents and packaging material in the event that
the product must be returned.
8
1
2
3
4
6
5
7
8
9
10
11
USB 2.0 2-BAY RAID SYSTEM VIEWS
FRONT VIEW
1. System LED
Indicator
2. HDD LED Indicator
3. HDD Trays
REAR VIEW
4. Quick HDD release
levers
5. USB mini-B port
6. Reset Button
7. Mode Switch
8. Power Switch
9. DC IN
10. Fan
11. Lock Port
9
INSTALLING/REPLACING THE HARD DRIVES IN THE RAID
SYSTEM
When the HDD is not installed, simply slide the tray out of the drive bay without
using the lever and be cautious when lifting the RAID System with the trays
inside. When the HDD is installed, after lifting the level, the tray should easily be
released from the drive bay.
1. Lift the quick HDD release lever to release the selected HDD tray from the
desired drive bay.
2. Slide the HDD tray out of the drive bay.
10
Due to the design tolerance of the SATA HDD connector, however, the
HDD tray may not always be released from the drive bay easily, or may not be
released at all. If this occurs, carefully slide the HDD tray out of the drive bay
after lifting the quick HDD release lever.
3. When removed, the HDD tray appears as shown below.
4. Carefully slide the HDD into the drive tray.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Onnto Stockage
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur