Omnimount SAT 2 Manuel utilisateur

STEP 1 – Prepare the stand base.

Place speaker stand base (a) upside down on ground. Locate steel

isolation spikes and adjustment nuts (e). Thread adjustment nuts

approximately half way onto the spikes, and then thread spikes into

three holes on the stand base, until adjustment nuts touch the base.

Use caution when handling stand base, as the isolation spikes are

sharp and can scratch wooden floors.

Assembly Instructions for SAT2 Speaker Stand

b - Outer

post.

d - Inner

post.

Fig. 3

Parts List

a - Base. (2) Allen wrench

e - Steel isolation

spikes and adjustment

nut. (6)

f - Clamping

mechanism. (2)

i - Foam dampening

pad. (4)

n - Double sided adhesive pads (8)

k - 5mm screw mounts

bracket and clamp mechanism

to inner post. (2)

l - M4 Base to post screw. (4)

c - Adjustable

post assembly

(2).

Speaker to

bracket mounting

screws

#8c

1/4-20 5mm 4mm #8 #8h

(g)

(h)

(m)

(o)

Base and keyhole

bracket

(Klipsch ProMedia)

45 deg.back

bracket (Klipsch)

90 deg.back

bracket

Angle bracket

(Klipsch)

Fig. 1

STEP 2 – Attach the post assembly.

Locate adjustable post assembly (c). Loosen set screw (see Fig. 3) on

back of outer post (b) using supplied Allen wrench.

Turn adjustable post assembly upside down and gently shake it until inner

post (d) becomes accessible. Pull inner post out approximately six inches.

Rotate inner post until speaker wire port is in line with set screw, and then

re-tighten set scre

re-tighten set screw.

Insert speaker wire into speaker wire port, run wire down through adjustable

post assembly, and then thread it through center hole in top of speaker base.

Be sure to leave enough slack at the ends so that wire doesn’t get pulled

out during remainder of assembly process. Attach adjustable post assembly

to speaker stand base with two base post screws (l), as shown in Fig. 1,

being careful not to pinch speaker wire. Make sure that speaker wire port is

pointing away from the front of the base, which is marked withpointing away from the front of the base, which is marked with

OmniMount label.

STEP 3 - Select the appropriate speaker adaptor. See Figure 2.

If your speaker comes with a threaded insert in the back or

on the bottom, use bracket (g), (h), (j), (m) or (o).

For brackets (h), (m) or (o), go to step 4.

For keyhole bracket (g), go to step 4.2.

If your speaker does not come with a mounting insert, you will need toIf your speaker does not come with a mounting insert, you will need to

use the clamping mechanism (f).

For clamping mechanism, go to step 4.1.

foam dampening

pads

move rails

all of the way

out

Fig. 4

Outer

post. (b)

Fig. 2

Set screw

Inner

post. (d)

side rails fit

snugly against

speaker equal distance

on both sides

side rails

knob

Fig. 5

Fig. 6 Fig. 7

Inner

post. (d)

mounting

screw(k)

Autres manuels Omnimount Support et étagère

Omnimount

Omnimount OM10051 Manuel utilisateur

Omnimount

Omnimount 10035 Manuel utilisateur

Omnimount

Omnimount PMD.5 Manuel utilisateur

Omnimount

Omnimount 10064 Manuel utilisateur

Omnimount

Omnimount OM1100595 Manuel utilisateur

Omnimount

Omnimount 30.0 STMP Manuel utilisateur

Omnimount

Omnimount 10323 Manuel utilisateur

Omnimount

Omnimount OS50FM Manuel utilisateur

Omnimount

Omnimount OM10049 Manuel utilisateur

Omnimount

Omnimount FP-CL Manuel utilisateur

Omnimount

Omnimount OM10046 Manuel utilisateur

Omnimount

Omnimount WS-2 Manuel utilisateur

Omnimount

Omnimount OMNI 25.0W Manuel utilisateur

Omnimount

Omnimount 10048 Manuel utilisateur

Omnimount

Omnimount IES1 Manuel utilisateur

Omnimount

Omnimount OE150FM Manuel utilisateur

Omnimount

Omnimount OM10245 Manuel utilisateur

Omnimount

Omnimount CPLP4 Manuel utilisateur

Omnimount

Omnimount PFC-A Manuel utilisateur

Omnimount

Omnimount OL80F Manuel utilisateur

Omnimount

Omnimount 30.0 CA Manuel utilisateur

Omnimount

Omnimount OMNI 25.0C Manuel utilisateur

Omnimount

Omnimount OS40TP Manuel utilisateur

Omnimount

Omnimount RE12W Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur