Oki T400 Manuel utilisateur

FCC WARNING

You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

AC power cord with ferrite core must be used for RF interference suppression.

◆Contents ◆

Name of Parts ............................... 2

Power .............................................. 6

Computer Connection................... 8

Paper Setting................................. 9

Ribbon Setting ..........………….. 11

Does not print correctly .............. 13

When error light is ON ............... 14

Failure? ....................................... 15

Name of Parts

■Front View

Top cover

Paper check

window

Operation switch

Power switch

Front cover

■Top cover .................... Open this cover when you set the paper.

■Power switch ..............Press this switch to turn ON/OFF the printer.

■Paper check window...To check the status of paper.

■Front cover.................Open this cover to refill or set DIP-SW.

■Operation switch

• POWER ....When you turn on the power, the green light lights up. Refer to

“Starting/Power”.

• ERROR .....When an error occurs, the red light turns ON. Refer to

“When error light is ON”.

• ONLINE ...When the green light is ON, the printer can receive data. When

the light is OFF, the printer cannot receive.

• [ONLINE] button ... Press this button to stop receiving data. Resume by

pressing this button again. If this button is pressed

while printing, the printing is suspended. To resume

printing, press this button again.

• [FEED] button ........When you press this button in the offline state, you

can feed paper. If you turn on the power of the printer

while you keep pressing this button, you can print out

the printer status.

Back View

Fanfold paper set in place

I/F Cover

Optional interface

Connecter

Power

Connector

■Power Connector...Connects AC adapter.

■Optional interface Connecter...Connects computer.

■Fanfold Paper set in place ...

Open this to use fanfold paper.To open the folder,

remove the Top Cover and release.

■I/F Cover... It removes by exchange of an I/F board.

※

Handling of an I/F Cover:

Please close with an I/F Cover after shutting off a power supply and

attaching or removing an I/F board, in case an I/F Cover is opened.

■Top Cover Open

Thermal head

Driver for darkness

adjustment

Paper holder

Head

Sensor

Paper holder

slide lever

Platen roller

Head Open/Close lever

■Paper holder ... When you use a roll paper, set the paper here.You can

adjust the width according to the paper size.

■Paper holder slide lever.. Press this lever to adjust the paper holder width.

■Head ................ Open this part to refill paper.

■Head Open/Close lever .. Press this to open the head.

■Thermal head .... This is the printing area. Please keep this part clean.

■Platen roller ...... This is the part that feeds paper. Please keep this part

clean.

■Sensor ................ Paper travels over this.

■Driver for darkness adjustment ... This is used to change the print darkness.

■Front Cover Open

Error number display

Print darkness

adjustment volume

Sensor level DIP-SW

■Print darkness adjustment volume ..You can finely adjust the darkness that

is set in the Printer Setting screen. See

the manual for details.

■Sensor level...... Do not use this. Only for used by service personnel.

■DIP-SW............ Appropriate settings are set according to your printer

system environment.You can change the settings. See the

manual for details.

■Error number display.. When the error light is ON, check the displayed

number. This number represents the reason of the

error. See the manual for details.

Power

Cable Connection

1 Connect the power cable with the

main unit and AC adapter as shown

in the figure. When you insert the

AC adapter in the main unit, set the

stopper firmly.

2 Plug in the power cable to the outlet.

3 Use a Two-prong adapter if only a

two-prong outlet is available.

1 Connect the power cable with the

main unit and AC adapter as shown

in the figure. When you insert the

AC adapter in the main unit, set the

stopper firmly.

2 Plug in the power cable to the outlet.

3 Use a Two-prong adapter if only a

two-prong outlet is available.

1 Connect the power cable with the

main unit and AC adapter as shown

in the figure. When you insert the

AC adapter in the main unit, set the

stopper firmly.

2 Plug in the power cable to the outlet.

3 Use a Two-prong adapter if only a

two-prong outlet is available.

Stopper

Always make sure to ground the power cable to the ground connector,

otherwise electric shock may result. Construct the ground facility if it

is not available.



Power Switch



Press the power switch at the front side of the main unit in the “|” direction.

* When you turn on the power, the POWER light lights up. Please confirm

this.



When you turn off the printer, flip the switch to the “ ” direction.

Autres manuels pour T400

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Oki Imprimante

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur