Oki LD610 T Manuel utilisateur
LD610
Options Installation Guide
Guide d’installation des options
Guía de instalación de accesorios
Manual de Instalação de Opcionais
note: You may have only one of these options. | remarque : Il est possible que vous n’ayez qu’une seule de ces options.
nota: Puede que sólo cuente con uno de estos accesorios. | nota: É possível que você tenha somente um desses opcionais.
Removal of The Bottom Housing Cover........................................3
Cutter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Dispenser Installation ......................................................7
Offset Position Adjustment .................................................11
Retrait du couvercle du boîtier inférieur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Installation du coupe-papier ................................................13
Installation du distributeur..................................................16
Réglage du décalage de position ............................................20
Cómo retirar la tapa protectora inferior........................................21
Instalación del cortador ...................................................22
Instalación del dispensador ................................................25
Ajuste de la posición offset.................................................29
Remoção da cobertura inferior da unidade ....................................30
Instalação do cortador ....................................................31
Instalação da unidade dispensadora .........................................34
Ajuste da posição de deslocamento..........................................38
3
REMOVAL OF THE BOTTOM HOUSING COVER
1. Make sure the printer is powered off and disconnect the
power cable and interface cable.
2. From the base of the printer, remove three screws (circled)
as shown.
CAUTION:
Ensure not to scrape the window portion when the
printer is turned over.
3. Remove the Bottom Housing cover.
Proceed to the next section(s) to install the desired option(s).
4. Follow the above steps in reverse sequence to reassemble
the Bottom Housing cover.
Notes:
• Ensurethewiringrouteneatlyasshownandarrangeall
thewiringtoavoidfrombeingpinchedwhenttingthe
bottom housing cover.
• WhenreassembletheBottom Housing cover to the
printer with IEEE interface terminal,iponeoftheclip
oftheinterfaceterminalasshown.ThenxtheBottom
Housing cover while holding the other clip, pulling the
Bottom Housing cover forward and downward.
screw x 3
clip
4
CUTTER INSTALLATION
To install the optional Cutter
1. First, follow the instructions in the Removal of the Bottom
Housing Cover section.
2. Turn over the printer in upright position. Pull the cover open/
close latches on both sides of the printer toward you to
unlock the Top cover, and then open the Top cover. Remove
the lower front cover by pulling the bottom slightly away
from the printer and lifting it upward.
3. Insert the latches of the Cutter Kit onto the holes located
below the two sides of platen roller of the printer and push
the Cutter Kit down to lock into place.
Close the top cover and turn the printer over again, with
the Main PCB is facing upward.
Note: Be sure to keep the cable positioned in the small
notch on the bottom edge of the Cutter Kit during
installation.
4. From the base of the Cutter kit, secure the cutter unit to the
printer with the supplied screw (circled) as shown.
Hole and latch
Cutter kit
5
CUTTER INSTALLATION (CONTINUED)
5. Connect the Cutter kit’s cable to the OPTION connector on
the MAIN PCB (connector is keyed).
Route the Cutter kit’s cable through the groove (circled) of
the printer as shown.
6. Assemble the Bottom Housing cover back to the printer and
secure with the three screws removed earlier.
CAUTION:
Ensure that no cables are pinched between parts when
you are assembling the cover.
Cutter kit’s
cable
OPTION
connector
MAIN PCB
To route the media when the cutter is installed
Loading of the media for cutter unit is similar to the usual procedure as explained in the Loading Labels
section of the of the LD610 User’s Technical Reference.
6
CUTTER INSTALLATION (CONTINUED)
Cut position Adjustment
If the cutting position is not at the regular position as mentioned below, you can change the offset setting with the
SBPL commands. Please refer to the Offset Position Adjustment section for the detailed procedures.
Notes when using media with optional cutter
• Cutting of Labels
The correct cutting position is at the label gap. Cutting
onto the label must be avoided because the label
adhesive that accumulates on the blade will affect cutter
sharpness.
• OncetheCutter Kit is installed, you must make the
appropriate settings selection in the Printer Driver:
1) In the Advanced Setup tab in Printing Preferences,
select your preferred settings in the Cutter and Print
Modesubsections.Whennished,clicktheApply button.
2) You also need to change the Operation Mode setting
after you click on the Store Settings button at the bottom
of the Advanced Setuptab.Whennished,clickthe
Send button.
• Cutting Media with Perforation
As for media with perforation, cutting on or in front
of the perforated lines is prohibited. Cutting in those
locations could cause the media to jam and the printer to
malfunction.
The perforated line +1 mm (+0.04") is the cut
prohibited zone (see Figure 1).
The folded perforated line +4 to +25 mm (+0.15" to
+0.98") of fan-folded paper is the cut prohibited zone
(see Figure 2).
Backing paper
Cut Position
Label
Cut Position
Label
Figure 1
Cut prohibited zone
(1mm, 0.04")
Perforated line
Figure 2
Fold perforation
25 mm, 0.98"
4 mm, 0.15"
7
DISPENSER INSTALLATION
To install the optional Dispenser
1. First, follow the instructions in the Removal of the Bottom
Housing Cover section.
2. Turn over the printer in upright position. Pull the cover open/
close latches on both sides of the printer toward you to
unlock the Top cover, and then open the Top cover. Remove
the lower front cover by pulling the bottom slightly away
from the printer and lifting it upward.
3. Before installing the Dispenser kit, open the Pressure
bracket by lifting upward and outward as shown.
4. Attach the latches of the Dispenser kit onto the holes
located below the two sides of platen roller of the printer.
Close the top cover, close the Pressure bracket by pushing
it in until it locks into place, then turn the printer over again,
with the Main PCB facing upward.
Note: Be sure to keep the cable off to the side during
installation.
1
2
Pressure
bracket
Hole and latch
8
DISPENSER INSTALLATION (CONTINUED)
5. From the base of the Dispenser kit, secure the cutter unit to
the printer with the supplied screw (circled) as shown.
6. Connect the Dispenser kit’s cable to the OPTION
connector on the MAIN PCB (connector is keyed). Route
the Dispenser kit’s cable through the groove (circled) of the
printer as shown.
7. Assemble the Bottom Housing cover back to the printer and
secure with the three screws removed earlier.
CAUTION:
Ensure that no cables are pinched between parts when
you are assembling the cover.
To route the label when the dispenser is installed
1. Withthepowersupplyoff,pullthecover open/close latches
on both sides of the printer toward you to unlock the top
cover, and then open the top cover. Make sure that the
coverrestsrmlysothatitwillnotfallforwardandinjureyour
hands.
2. Withyourthumbspositionedonthetwolowercornersofthe
pressure bracket (1), push the pressure bracket up and
pull it forward to open the pressure bracket.
1
1
2
Dispenser
kit
Dispenser
kit’s cable
OPTION
connector
MAIN PCB
Dispenser unit
Pressure
bracket
Dispenser bar
9
DISPENSER INSTALLATION (CONTINUED)
3. Peeloffthersttwoleadinglabelsfromtheliner(backing
paper) and then load the label roll on the media holder.
After pulling out the leading liner (backing paper), pass
the liner (backing paper) through the media guides
and then pass over the dispenser bar so as to cover it.
Then pass the liner (backing paper) behind the pressure
bracket as shown and out of the front of the printer from
below the pressure bracket (3).
4. If the paper is not taut, roll the paper on the media holder so
that the paper is taut.
Next, tightly close the pressure bracket with the liner
(backing paper) passing through it.
5. Close the top cover until it clicks into position.
6. After turning on the label, turn on the power.
The printer is online and the ON LINE (POWER) indicator
lights green.
When the printer is ready, press the FEED/LINE button
to output an empty label and stop at the dispenser. This
procedure is to ensure that the label is loaded correctly.
Media guides
Dispenser bar
Label output
from here
Output
backing
paper
10
DISPENSER INSTALLATION (CONTINUED)
Stop position Adjustment
Normally, the label is dispensed to the point where 2 or 3mm (0.08" or 0.1") of the label remain on the liner
(backing paper).
If the label is not dispensed at the regular position, you can change the offset setting with the SBPL commands.
Please refer to the Offset Position Adjustment section for the detailed procedures. After adjusting the stop
position,dispensetwoorthreelabelstoxthestopposition.
Notes:
• Theremaybecaseswhenthedispenserdoesnotfunctionproperlyduetothethicknessofthelabelsused.
• TheDispenserunitiseffectiveforlabelpitch22to100mm(0.86"to3.93").However,thelabelsizelimitation
may vary with application conditions.
• Labelsover100mm(3.9")maycurlatdispenserduetothenatureofthematerial.Thereisnoremedyforthis.
Autres manuels pour LD610 T
3
Table des matières
Langues :
Autres manuels Oki Étiqueteuse
Oki
Oki PRO330S Manuel utilisateur
Oki
Oki ES8434 Guide de configuration
Oki
Oki LD630 Series Manuel d'installation et d'exploitation
Oki
Oki Pro1040 Manuel utilisateur
Oki
Oki proColor Pro510DW Manuel utilisateur
Oki
Oki LD630T Manuel utilisateur
Oki
Oki LD670 Manuel utilisateur
Oki
Oki LD610 T Manuel d'utilisation et d'entretien
Oki
Oki proColor Pro510DW Manuel utilisateur
Oki
Oki LD620D Manuel utilisateur
Oki
Oki Pro1040 Manuel d'utilisation
Oki
Oki LD630 Series Manuel d'utilisation et d'entretien
Oki
Oki Pro1040 Manuel utilisateur
Oki
Oki Pro1040 Manuel utilisateur
Oki
Oki LD630 Series Manuel d'utilisation et d'entretien
Oki
Oki LE850 Manuel d'utilisation et d'entretien
Oki
Oki LD670 Manuel utilisateur
Oki
Oki C824 Guide de configuration
Oki
Oki LD620D Manuel utilisateur
