OHAUS Scout SPX Manuel utilisateur

Quick Start Guide ScoutSPX Balances

Ohaus Corporation www.ohaus.com iScoutSPX Balances

UNPACKING

Carefully remove your Scout balance and each of its components from the

package. Store the packaging material to ensure safe storage and future transport.

Included Components:

Balance

Pan

Quick Start Guide

Calibration Mass (only for models up to 620g

capacity)

Warranty Card

AC Adapter & Plug

SELECTING THE LOCATION

Place on a firm, steady surface with sufficient space. Avoid excessive air current,

vibrations, heat sources, or rapid temperature changes.

PREPARATION FOR USE

Step-1

Release the red Transportation

Lock on subplatform of the

balance

Turn the pointer 90counter-

clockwise.

Step-2

Install the Pan

Rectangular pan: Place diagonally

on sub-platform and rotate

counter-clockwise until it locks.

Round pan: Set straight down on

subplatform.

Step-3

Connect Power

Connect the AC Adapter to the

balance input jack.

Battery Installation

Install the Four “AA” (LR6)

batteries (not included) with

polarity as shown in the battery

compartment.

Step-4

Level the balance

Level the balance before using by

adjusting the feet until level

bubble is center

AC Adapter Jack

Battery

Compartment

Subplatform

Transportation

Lock Pointer

Unlocked

Position

Locked

Position

Visit www.scaleman.com to purchase the Ohaus Scout SPX Scales

See the entire line of Ohaus Scales at www.balances.com

ScoutSPX Balances Quick Start Guide

ScoutSPX Balances ii Ohaus Corporation www.ohaus.com

SAFETY PRECAUTIONS

CAUTION: Read all safety warnings before installing, making

connections, or servicing this equipment. Failure to comply with these

warnings could result in personal injury and/or property damage. Retain

all instructions for future reference.

Verify that the local AC power supply voltage is within the input voltage range

printed on the AC adapter’s ratings label.

Only connect the AC adapter to a compatible grounded socket.

Position the instrument such that the AC adapter can be easily disconnected

from the socket.

Position the power cord so that it does not pose a potential obstacle or tripping

hazard.

Operate the equipment only under ambient conditions specified in the user

instructions.

Do not operate the equipment in hazardous or explosive environments.

Disconnect the equipment from mains power before cleaning or servicing.

Service should only be performed by authorized personnel.

CONTROLS

Button Functions

COUT

Visit www.scaleman.com to purchase the Ohaus Scout SPX Scales

See the entire line of Ohaus Scales at www.balances.com

Quick Start Guide ScoutSPX Balances

Ohaus Corporation www.ohaus.com iii ScoutSPX Balances

Button

Short Press

Zero/On

Turns the

balance on;

If balance is

On, sets Zero

Initiates print

Function

Initiates an

application

mode

Tare

Long Press

Off

Turns the

balance Off

Units

Changes the

weighing unit

Mode

Changes the

application

mode

Enters the

User menu

Short Press

(Menu

Function)

Yes

Accepts the

current setting

Advances to

the next menu

or setting

Back

Moves to

menu item

Exit

Exits the User

CALIBRATION

When the balance is operated for the first time, a span calibration is

recommended to ensure accurate weighing results. With balance turned on:

Step-1

Press and hold Menu until [mMeNU] (Menu) is displayed.

Step-2

Release the button, the display will show [C.A.L].

Step-3

Press Yes to accept. [SpaN] will then be shown.

Step-4

Press Yes to begin the span calibration. Zero reading is stored

automatically.

Step-5

Place the specified span calibration mass on the pan. Then, press Yes to

accept the weight or No to select an alternate weight.

[--C--] will be displayed while the reading is stored

The display will show [done] if the calibration was successful. The balance

returns to the previous application mode and is ready for use.

OPERATION & APPLICATIONS

The balance can be configured to operate in various Application modes. Press

and hold Mode key to select your Application mode.

The Scout SPX balance incorporates the following Applications:

[wWEIGH]

[Count]

[Percnt]

[CHECk]

[total]

[Hold]

Weighing

Parts

Counting

Percent

Weighing

Check

Weighing

Totalization

Display

Hold

Visit www.scaleman.com to purchase the Ohaus Scout SPX Scales

See the entire line of Ohaus Scales at www.balances.com

ScoutSPX Balances Quick Start Guide

ScoutSPX Balances iv Ohaus Corporation www.ohaus.com

Weighing

1. Press the Zero/On button to turn the balance on.

2. Select Weighing (this application is the default) by pressing & holding Mode

key.

3. Press Tare or Zero if necessary to begin.

4. Place objects on the pan to display the weight. When stable, the appears.

The display shows the resulting value of the sample.

MENU STRUCTURE

Sub-Menus

C.a.l

S.e.t.u.p

M.o.d.e

U.n.i.t

E.n.d

User Menu

Items:

Span

Lin

Reset Yes/No

Filter

Low/Med/High

AZT0.5/1/3/Off

StableRange

0.5/1/2//5

Backlight

Off/On/Auto

Auto Tare

Off/On/On-acc

Auto Off

Off/1/5/10

Reset Yes/No

Weighing

On/Off

Counting

On/Off

PercentOn/Off

Check On/Off

TotalizeOn/Off

Hold

Disp/Peak/Off

Reset

ozt

dwt

lb:oz

grn

hkt*

sgt*

twt*

tola/tical

End

Note: Bold fonts are default settings in the menus. * Only available in certain regions.

ADDITIONAL FEATURES

Connecting the Interface

Use an optional interface connectivity kit to

connect the balance either to a computer,

printer or OHAUS auxiliary display.

Below Interface kit accessories are available:

RS232, USB Host, USB Device, Ethernet,

Bluetooth*.

Interface connection on the rear of

the balance:

* Interface kits may vary according to local regulations

No/Back

Long press -

Enter menu

Short press -

Short press –

Go to

Next/Prev.

Yes

Exit

Short press –

Exit menu

Interface connection

AC Adapter jack

Security slot

Visit www.scaleman.com to purchase the Ohaus Scout SPX Scales

See the entire line of Ohaus Scales at www.balances.com

Quick Start Guide ScoutSPX Balances

Ohaus Corporation www.ohaus.com vScoutSPX Balances

Weigh Below Hook

The weigh below hook is located at the reverse side of the battery cover as shown.

To use this feature, remove the red protective cover underneath for the weigh below

opening.

COMPLIANCE

Compliance to the following standards is indicated by the corresponding mark on

the product.

Mark

Standard

This product complies with the EU Directives 2014/30/EU (EMC),

2014/35/EU (LVD) and 2014/31/EU (NAWI). The EU Declaration of

Conformity is available online at www.ohaus.com/ce.

This product complies with the EU Directive 2002/96/EC (WEEE).

Please dispose of this product in accordance with local regulations at

the collecting point specified for electrical and electronic equipment.

For disposal instructions in Europe, refer to www.ohaus.com/weee.

AS/NZS 61000.6.1, AS/NZS 61000.6.3

CAN/CSA-C22.2 No. 61010-1

UL Std. No. 61010-1

INSTRUCTION MANUAL

For more detailed information about the balance,

please refer to the product instruction manual. The

instruction manual can be obtained either by

scanning the QR code or by going to the product

page and from there download it. Go to

www.ohaus.com to register your product's warranty.

Product Page: http://www.ohaus.com/

QR Code:

Weigh below protective cover

Weigh

below

hook

Visit www.scaleman.com to purchase the Ohaus Scout SPX Scales

See the entire line of Ohaus Scales at www.balances.com

Autres manuels pour Scout SPX

Table des matières

Autres manuels OHAUS Échelle

OHAUS

OHAUS Adventurer Pro Manuel utilisateur

OHAUS

OHAUS Scout STX123 Manuel utilisateur

OHAUS

OHAUS Scout pro Manuel utilisateur

OHAUS

OHAUS Navigator NV222 Manuel utilisateur

OHAUS

OHAUS Scout pro Manuel utilisateur

OHAUS

OHAUS Defender 3000 Manuel utilisateur

OHAUS

OHAUS Scout SPX Series Manuel utilisateur

OHAUS

OHAUS Ranger 3000 Series Manuel utilisateur

OHAUS

OHAUS CS200P Manuel utilisateur

OHAUS

OHAUS PX Series Manuel utilisateur

OHAUS

OHAUS PS Series Manuel utilisateur

OHAUS

OHAUS CS 200 Manuel utilisateur

OHAUS

OHAUS RI Series Manuel utilisateur

OHAUS

OHAUS Adventurer series Manuel utilisateur

OHAUS

OHAUS Ranger 4000 Count Series Manuel utilisateur

OHAUS

OHAUS PS121 Manuel utilisateur

OHAUS

OHAUS Valor 3000 Manuel utilisateur

OHAUS

OHAUS CL Series Manuel utilisateur

OHAUS

OHAUS 750-S0 Manuel utilisateur

OHAUS

OHAUS ranger 7000 Manuel utilisateur

OHAUS

OHAUS Adventurer Pro Grain Manuel utilisateur

OHAUS

OHAUS Adventurer SL AS64 Manuel utilisateur

OHAUS

OHAUS Scout pro Manuel utilisateur

OHAUS

OHAUS ES6R Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur