OHAUS Catapult 1000 Manuel utilisateur

Quick Start Guide Catapult 1000

Ohaus Corporation www.ohaus.com iCatapult 1000 Scales Quick Start Guide

PREPARATION FOR USE

Check Power

If using AC power, be sure local line voltage

matches voltage printed on the scale’s power

adapter. If not, do not use AC power.

Connect adapter plug to input jack at rear.

To use battery power, remove battery cover

and insert three LR14 (“C”) batteries.

Allow at least five minutes warm-up time,

for scale to stabilize before operation.

SELECTING THE LOCATION:

Place on a firm, steady surface with sufficient space.

Avoid excessive air current, vibrations, heat sources, or rapid temperature changes.

SAFETY PRECAUTIONS

For dependable operation of this product, observe the following precautions:

•Verify that the input voltage printed on the power Adapter and the plug type

matches the local power supply (if using AC power).

•Make sure that the power cord does not pose an obstacle or tripping hazard.

•Disconnect the product from the power supply when cleaning.

•Do not operate this product in hazardous or unstable environments.

•Do not drop loads on the pan.

•Use only approved accessories and peripherals, as available.

•Operate the product only under ambient conditions specified in the Instruction

Manual.

•Service should be performed by authorized personnel only.

Power Input Jack

Catapult 1000 Quick Start Guide

Catapult 1000 Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com

CONTROLS

Button Functions

UNITS

Cal

Short Press

Long Press

Changes weighing unit and weighing mode.

In Dynamic Weighing Mode, starts countdown.

Starts calibration.

ON/ZERO

Off

Short Press (when off)

Short Press:(when on)

Long Press

Turns scale on.

Sets display to zero.

Turns scale off.

OPERATION

Power On: Press

All display segments appear, then the software version.

Display resets to zero.

To Zero: Press

when scale is on, display returns to zero.

To Tare: Press

with container on scale. Add mass to see NET weight.

If both sample and container are removed, display shows a negative value.

Overload: If load exceeds scale capacity, “E” appears. Remove load, scale returns to normal.

Auto Shut-Off: When running on batteries, scale turns off after four inactive minutes.

Dynamic Weighing

With platform empty, press

repeatedly until bullet • flashes.

Place a mass on the platform. The scale shows “-A-”.

(If using a container, press ZERO to tare.)

ress

to start the averaging countdown from 5 seconds.

Averaged weight appears. Bullet • stops flashing when process is complete.

Display holds until a button is pressed.

To Exit, remove mass from platform. Press

until kg or lb appears on display.

*80253136*

P/N 80253136

Stability

symbol

Battery charge

symbol

Symbols for weighing modes:

lb – Pounds

•

– Dynamic Weighing

kg – Kilograms

Negative

symbol

Autres manuels pour Catapult 1000

Table des matières

Autres manuels OHAUS Échelle

OHAUS

OHAUS ES30R Manuel utilisateur

OHAUS

OHAUS 1119D Manuel utilisateur

OHAUS

OHAUS EB3 Manuel utilisateur

OHAUS

OHAUS Scout pro Manuel utilisateur

OHAUS

OHAUS SD Series Manuel utilisateur

OHAUS

OHAUS HS-120 Manuel utilisateur

OHAUS

OHAUS PS Series Manuel utilisateur

OHAUS

OHAUS HH 120D Manuel utilisateur

OHAUS

OHAUS Courier 7000 Manuel utilisateur

OHAUS

OHAUS Adventurer AR0640 Manuel utilisateur

OHAUS

OHAUS RC41M15-M Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS ES series Manuel utilisateur

OHAUS

OHAUS Valor 1500 Series Manuel utilisateur

OHAUS

OHAUS TROOPER Manuel utilisateur

OHAUS

OHAUS Ranger Count Plus Manuel utilisateur

OHAUS

OHAUS Valor 1000 Manuel utilisateur

OHAUS

OHAUS Valor 3000 Manuel utilisateur

OHAUS

OHAUS ranger 7000 Manuel utilisateur

OHAUS

OHAUS FD Series Manuel utilisateur

OHAUS

OHAUS Ranger Manuel utilisateur

OHAUS

OHAUS DS Series Manuel utilisateur

OHAUS

OHAUS CF1000R Manuel utilisateur

OHAUS

OHAUS Emerald Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur