NTI ENVIROMUX E-5D Manuel utilisateur

E-xD: RESTORE DEFAULTS VIA RS232

This procedure is provided to enable the administrator to restore defaults to the E-5D\16D using the “RS232” port.

Note: This procedure has been tested to work properly using Microsoft®HyperTerminal. We cannot confirm whether

other terminal programs will give satisfactory results.

1.Connect one end of a CAT5 patch cable (supplied) to the port labeled “RS232” on the rear of the E-16D (or front of the E-5D).

Plug the other end of the CAT5 cable into an RJ45-to-DB9F adapter (supplied), and connect the adapter to the RS232 port on the

control terminal.

Connect a terminal for direct RS232 serial communication

2. Using the terminal connected to the ENVIROMUX, start the terminal program (e.g. Windows HyperTerminal) and configure it

as follows:

direct connection (using the appropriate CPU local serial Com port)

115200 bps

8 bits

no parity

1 stop bit

no flow control

VT100 terminal mode.

3. Power ON the ENVIROMUX and as the ENVIROMUX begins to boot, press and hold the <Tab> key. (If you fail to press this

key in time the system will continue booting and you will have to power OFF the ENVIROMUX and start over.)

Erase the configuration of the ENVIROMUX

4. At the “SEMS-16>” prompt, type;

SEMS-16> nand erase config

5. Press <Enter> key.

The ENVIROMUX will erase all configuration settings and restore the ENVIROMUX to factory default settings. ALL USER

CONFIGURATION AND SENSOR CONFIGURATION SETTINGS WILL BE LOST.

When finished, the “SEMS-16>” prompt will return.

6. At the prompt, type reset and press <Enter>. The ENVIROMUX will restart.

and erase confi

eset

Restoring the default configuration of the ENVIROMUX

7. As the ENVIROMUX restarts, it will restore defaults (as shown in image above) and then present the ENVIROMUX login screen

(below).

Text Menu Login Screen

At this point you can either access the ENVIROMUX using the Device Discovery Tool (found on the manual CD and our website

at http://www.networktechinc.com/download/d-environment-monitor-16.html ) to change the network settings back to what they

were, or you can login to the text menu (below) using the default administrative user “root” and password “nti”.

From the text menu, to change the network settings, enter <4>, then <1> to get to the network configuration menu.

Enter your settings.

Be sure to <Tab> to the Save and press <Enter> before exiting the menu.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NTI Instrument de mesure

NTI

NTI ENVIROMUX Series Manuel utilisateur

NTI

NTI ENVIROMUX Series Manuel utilisateur

NTI

NTI ENVIROMUX Series Manuel utilisateur

NTI

NTI E-BEEP2-x Mode d’emploi

NTI

NTI USB-A+A-5M Manuel utilisateur

NTI

NTI ENVIROMUX Series Manuel utilisateur

NTI

NTI ENVIROMUX Series Manuel utilisateur

NTI

NTI ENVIROMUX-16D Manuel utilisateur

NTI

NTI ENVIROMUX-16D Manuel utilisateur

NTI

NTI ENVIROMUX-MINI-LXO Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur