NPM Motionnet MNET-D340 Manuel utilisateur

YA7082-0/1

RemoteI/O & RemoteMotion

Local Input Board

Nippon Pulse Motor Co., Ltd.

Motionnet Local Input Board MNET-D340 YA7082-0/1

Table of Contents

1. Preface...................................................................................................................................................... 1

2. Features.................................................................................................................................................... 3

3. Handling Precautions.............................................................................................................................. 4

4. Warranty Period and Coverage .............................................................................................................. 4

5. Specifications .......................................................................................................................................... 5

6. Configuration ........................................................................................................................................... 7

7. Connector Pin Assignment..................................................................................................................... 8

7-1. CN1 (input signal connector 1) ....................................................................................................... 8

7-2. CN2 (input signal connector 2) ....................................................................................................... 8

7-3. CN3, 4 (serial communication connector) ..................................................................................... 9

7-4.CN5 (power connector) ..................................................................................................................... 9

7-5. Connectors used .............................................................................................................................. 9

8. Signals and Functions .......................................................................................................................... 10

8-1. Input signal (IN*, INCOM*+, INCOM*-)........................................................................................... 10

8-2. Serial communication (RS485+, RS485-) ......................................................................................11

8-3. Power requirements (24V, GND, FG) .............................................................................................11

9. Settings................................................................................................................................................... 12

9-1. Setting the serial communication device number (SW1) ........................................................... 12

9-2. Setting the serial communication parameters (SW2) ................................................................. 12

9-2-1. Setting the data transfer speed (B0, B1) ............................................................................... 12

9-2-2. Setting the output signal status to use when a communication error occurs (TD) ......... 12

9-2-3. Setting the watchdog timer (TM)............................................................................................ 13

9-2-4. Break frame request (BK) ....................................................................................................... 13

9-2-5. Setting the termination resistance (TR) ................................................................................ 13

10. Status Display ...................................................................................................................................... 14

10-1. Communication status display LED (RUN) ................................................................................ 14

10-2. Communication status display LED (ERR) ................................................................................ 14

10-3. Power indicator LED (3.3 V)......................................................................................................... 14

10-4. Input/Output signal display LED ................................................................................................. 14

11. Serial Communication Connection Cable ......................................................................................... 15

12. Allocation of Switches and Connectors............................................................................................ 16

13. External Dimensions ........................................................................................................................... 17

- C1 -

Remote/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

1. Preface

Thank you for purchasing our input board, a local board from our Motionnet ultra-high speed serial

communication system series.

□

The MNET-D340 board you have purchased is a 32-point parallel input board which contains a G9002

IO device for ultra-high speed serial communication.

This board is controlled by a center board, which is equipped with a G9001A Motionnet Center device.

Use the center board together with this board.

□

Motionnet is an ultra-high-speed serial communication system created by NPM (Nippon Pulse Motor).

Using our four specially developed devices (G9001A, G9002, G9003, and G9004) as core chips, this

serial communication system is a complete system for reducing wiring while affording remote operation

by emulating a CPU and handling CPU message communications, as well as controlling input and

output, at transfer speeds of 20 Mbps.

Device

G9001A: Center device

This is a central controller that manages local devices. This device has 256 bytes of RAM for I/O

control, and 512 bytes for data communication. This device can be operated from a remote CPU

just like accessing a memory. It can be connected to a maximum of 64 local devices (G9002,

G9003, and G9004).

G9002: IO device

This is a local I/O control device that can control 32 separate I/O signals.

G9003: PCL device

This is a local device containing a pulse control LSI that has been developed and polished by NMP

for use in motion control over many years. It also has a serial communication function. It can control

single-axis pulse input type stepper motors and servomotors.

G9004: CPU emulation device

This is the most sophisticated local device in the Motionnet series, and it can remotely control other

LSIs that need a connection to a CPU (for example a PCL6045B made by NPM). By connecting a

CPU to its local side, it can also communicate messages between CPUs.

RemoteI/O

If a Motionnet line is only used for input and output control, it can send and receive signals for 2048

points on 64 local devices in 0.97 msec (using a 20 Mbps data transfer speed). (If a smaller number of

devices are connected, the data transfer time will be proportionally shorter.)

RemoteMotion

If a Motionnet line is only used to control motors, it can control up to 64 axes. With this type of control,

individual devices can control pulse-input type stepper motors and servomotors. They can execute

continuous operations at constant speed, linear acceleration/deceleration, and S-curve

acceleration/deceleration, as well as carry out preset positioning operations, and zero return operations.

- 1 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

A system combining these two motor types is also possible.

Although it depends on the number of devices connected and the data transfer speed selected, the

cable length can be extended up to 100 m using an ordinary CAT5 LAN cable.

The serial communication uses a receive-respond type protocol. This protocol adds a CRC

number to the communication frame to detect errors, thus offering higher reliability. You can use it

without worrying about the accuracy of the communication.

□

This instruction manual describes the specifications and methods for using the MNET-D340. We want

you to read this manual thoroughly and get full use of the functions offered by this board.

This manual does not describe the detailed functions of the G9001A and G9002 LSIs for

ultra-high-speed serial communication systems.

For the details about the functions and registers of these LSIs, please read NPM's "User's Manual for

the G9001A/G9002, LSIs for the Motionnet ultra-high speed serial communication system."

- 2 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

2. Features

Data transfer speed

20 Mbps, maximum

Data transfer cycle

A maximum of 0.97ms, when using 64 I/O boards.

(At a transfer speed of 20 Mbps, and using our recommended 50 m cable.)

Number of devices that can be connected

Maximum 64 I/O boards/line, with 2048 points connected.

Connection method

Multi-drop connections using LAN cables.

Serial communication types

Three types of communication are available.

1) System communication

By polling the Motionnet line, the number of local devices that are connected, the device numbers,

device types, and I/O port allocation status can all be checked.

2) Cyclic communication

The system starts communication with the local device that has the lowest device number. When

the communication cycle reaches the device with the highest device number, the system starts over

again, communicating with the device that has the lowest device number. The process of

communicating with all active devices, from the lowest to the highest device, is one cycle. The

system always repeats this communication cycle, automatically.

Input and output are controlled using cyclic communication.

3) Data communication

This type of communication is used to read and write data between a PCL device and a CPU

emulation device.

Data is written into a FIFO buffer in the center device, and then a send command is issued. These

communications are sent and received automatically, during the interrupt driven cyclic

communications.

Communication error detection

Errors can be detected by adding CRC numbers to the serial communication frames.

Input

- Number of input points: 32 points

- Isolation method: Photocouplers

Common input specifications

8 input points are configured as one group. This group is independent from all other groups. Each

group has one common line. Using jumpers, they can be connected to the power supply that is also

supplying power to the power connector.

- 3 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

3. Handling Precautions

Inputting power

Do not connect or disconnect connectors while this board or peripheral circuits are supplied with

power.

Static electricity

This board uses a CMOS device. Therefore this board must be stored in a package in which it was

shipped until you actually use it, in order to prevent damage from static electricity.

Switch settings

This board is equipped with switches to set device number and details for serial communications.

Be sure to shut off the power supply to the board before changing these switches.

Connections to electrically noisy devices

Interference from excessively noisy devices or from power surges on the power and I/O circuits may

cause the board to malfunction. To connect to a device, which may generate electrical noise, we

recommend taking countermeasures, such as attaching a protective circuit to the input/output circuits.

However, it is best not to share the same power supply with noise generating sources.

Heat generation of circuit elements

Input resistors, output transistor arrays, and other elements may generate heat and thus become

hot, depending on the operating conditions. If this happens, take steps such as using forced

cooling.

4. Warranty Period and Coverage

Warranty period

12 months after being shipped from our factory.

Warranty coverage

During the warranty period, we will repair without charge any problems on the board that occurred

while it was being used appropriately, and where the cause of the problem is due to us.

However, the following cases will be not be covered by the warranty, even if the warranty period has

not expired.

- Problems caused by inappropriate handling or use.

- Problems caused by using parts not made or approved by us.

- Problems caused by modifications made to the board that were not authorized by NPM.

- Problems caused by disasters, accidents, or fires.

We warranty only the product as delivered, and we do not accept responsibility for any loss caused by

a fault in our product. We will repair the board when the user sends it to our plant.

- 4 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

5. Specifications

Specifications of this board are shown below.

Item Signal

name Specifications

Cyclic communication times and

data transfer cycles

Maximum of 0.12 msec, when using 8 devices. #1

Maximum of 0.24 msec, when using 16 devices. #1

Maximum of 0.49 msec, when using 32 devices. #1

Maximum of 0.97 msec, when using 64 devices. #2

(Data transfer speed: 20 Mbps, when using our

recommended cable #1:100m, #2: 50m)

Total serial communication line

length

Maximum of 100 m (At a data transfer speed of 20

Mbps with 32 devices connected)

Maximum of 50 m (At a data transfer speed of 20

Mbps with 64 devices connected)

Maximum of 100 m (At a data transfer speed of 10

Mbps with 64 devices connected)

(Using our recommended cables)

Serial communication interface Pulse transformer and RS-485 specification line

transceiver

Serial communication protocol Our proprietary protocol

Serial communication coding

method NRZ signed

Serial communication method Half-duplex communication

Connection method Multi-drop connection using a LAN cable or our

proprietary cable.

Serial communication device

number

SW1-

A0 to A5

Assignable device numbers, 0 to 63.

Set using switches.

Serial communication transfer

speed

SW2-

B0, B1

20 Mbps/10 Mbps/5 Mbps/2.5 Mbps

Set using switches.

Output status setting when a

communication error occurs SW2-TD

Maintain current status / Reset

Select one using a switch

(The selected output is used when the watchdog

timer times out during communication)

Watchdog timer setting SW2-TM

When 20 Mbps is selected: 20 msec. / 5 msec.

When 10 Mbps is selected: 40 msec. / 10 msec.

When 5 Mbps is selected: 80 msec. / 20 msec.

When 2.5 Mbps is selected: 160 msec. / 40 msec.

Select one of the above using a switch.

(This is the data sending interval allowed by the

center device.)

Break frame request SW2-BK Send a break frame.

Set using a switch.

Termination resistance setting SW2-TR

Enable termination resistance on the last device on

a serial line.

Set using a switch.

Display serial communication

status

RUN

ERR

RUN: While receiving serial communications

normally, the green LED is lit.

ERR: When a serial communication error occurs

continuously, the red LED is lit.

Input/output status display

Input: The green LED goes on when the input

photocoupler turns on.

Output: The red LED goes on when the output

transistor turns on.

Selection of a common line JP1 to 8

Connection between the input/output circuit

commons and CN5, the input power terminal.

Set using a jumper connector.

G9002 reference clock 80 MHz

- 5 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

Item Signal

name Specifications

Input

- Number of points: 32 (one common line for each 8 points)

- Photocoupler input (sink type output)

- Input signal voltage: 24 VDC

- Input signal current: 4.2 mA/point (Typ.)

- Response time: 55 msec (Typ.)

Power requirements CN5-24 V,

GND

24 VDC±10%, 55 mA (Typ.)

(The current value given above is true when 24 VDC is input and

there is no connection with the input/output circuit common.)

Power indicator 3.3 V Yellow LED Indicates that 3.3 VDC internal control power is

being output.

Operating

temperature range *1 0 to +40˚C

Operating ambient

humidity 80%RH or less

(Non condensing through the +10˚C to +40˚C range)

Vibration proof Complies with JIS C0040

Installation method Using DIN rail.

(DIN rails are not supplied as accessory.)

Dimensions W124x D72.5 x H50 (Unit: mm)

*1: The input current resistors have a loss of 0.12 W per point. Consider the heat generated by these

transistors in use.

- 6 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

6. Configuration

A block diagram is shown below.

OUTCOM1+ to 4+

OUTCOM1- to 4-

CN5

Common selection

5V, 3.3V 24V

GND

DC/DC

converter

Input

interface

P30 to P37

P20 to P27

CN2

IN17 to

IN24

INCOM3+

INCOM3-

IN25 to

IN32

INCOM4+

INCOM4-

Input

interface

Input

interface

SW2

Serial communication

setting switch

SW1

P10 to P17

RS-485 line

transceiver

CN4

BRK

TUD

JP1 to 8

CLK

TMD

SPD0, 1

DN0 to 5

SOEH

80MHz

Quartz oscillator

Device number

setting switch

G9002

Motionnet

IO device

P00 to P07

Pulse

transformer

CN1

CN3

Serial communication line

IN1 to

IN8

INCOM1+

INCOM1-

IN9 to

IN16

INCOM2+

INCOM2-

Input

interface

- 7 -

Remote I/O & Remote Motion

Motionnet Local Input Board MNET-D340 YA7082-0/1

7. Connector Pin Assignment

7-1. CN1 (input signal connector 1)

Connect 16 points of input signals.

No.

ignal nam

Function No.

ignal nam

Function

1 IN1 Input signal 1 2 INCOM1+ Input signal common 1+

3 IN2 Input signal 2 4 INCOM1+ Input signal common 1-

5 IN3 Input signal 3 6 INCOM1+ Input signal common 1+

7 IN4 Input signal 4 8 INCOM1+ Input signal common 1-

9 IN5 Input signal 5 10 INCOM1+ Input signal common 1+

11 IN6 Input signal 6 12 INCOM1+ Input signal common 1-

13 IN7 Input signal 7 14 INCOM1+ Input signal common 1+

15 IN8 Input signal 8 16 INCOM1- Input signal common 1-

17 IN9 Input signal 9 18 INCOM2+ Input signal common 2+

19 IN10 Input signal 10 20 INCOM2+ Input signal common 2-

21 IN11 Input signal 11 22 INCOM2+ Input signal common 2+

23 IN12 Input signal 12 24 INCOM2+ Input signal common 2-+

25 IN13 Input signal 13 26 INCOM2+ Input signal common 2+

27 IN14 Input signal 14 28 INCOM2- Input signal common 2-

29 IN15 Input signal 15 30 INCOM2+ Input signal common 2+

31 IN16 Input signal 16 32 INCOM2- Input signal common 2-

33 INCOM2+ Input signal common 2+ 34 INCOM2- Input signal common 2-

7-2. CN2 (input signal connector 2)

Connect 16 points of input signals.

No.

ignal nam

Function No.

ignal nam

Function

1 IN17 Input signal 17 2 INCOM3+ Input signal common 3+

3 IN18 Input signal 18 4 INCOM3- Input signal common 3-

5 IN19 Input signal 19 6 INCOM3+ Input signal common 3+

7 IN20 Input signal 20 8 INCOM3- Input signal common 3-

9 IN21 Input signal 21 10 INCOM3+ Input signal common 3+

11 IN22 Input signal 22 12 INCOM3- Input signal common 3-

13 IN23 Input signal 23 14 INCOM3+ Input signal common 3+

15 IN24 Input signal 24 16 INCOM3- Input signal common 3-

17 IN25 Input signal 25 18 INCOM4+ Input signal common 4+

19 IN26 Input signal 26 20 INCOM4- Input signal common 4-

21 IN27 Input signal 27 22 INCOM4+ Input signal common 4+

23 IN28 Input signal 28 24 INCOM4- Input signal common 4-

25 IN29 Input signal 29 26 INCOM4+ Input signal common 4+

27 IN30 Input signal 30 28 INCOM4- Input signal common 4-

29 IN31 Input signal 31 30 INCOM4+ Input signal common 4+

30 IN32 Input signal 32 32 INCOM4- Input signal common 4-

31 INCOM4+ Input signal common 4+ 34 INCOM4- Input signal common 4-

- 8 -

Remote I/O & Remote Motion

Table des matières

Autres manuels NPM Système d'E/S

NPM

NPM Motionnet MNET-D304 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur