Norton BBL547 Manuel utilisateur

OWNERS

MANUAL

Block Buster Large Masonry Saw

Models:

BBL547 BBL527

BBL5247 BBL7247

BBL1347 BBL1327 BBL13247

Form BBL527-1327 Manual Rev 12-2010

WARRANTY

Norton Construction Products warrants all products manufactured by

it against defects in workmanship or materials for a period of one (1)

year from the date of shipment to the customer.

The responsibility of Norton Construction Products under this

warranty is limited to replacement or repair of defective parts at Saint-

Gobain Abrasives, Inc. Stephenville, Texas factory, or at a point

designated by it, of such part as shall appear to us upon inspection at

such point, to have been defective in material or workmanship, with

expense for transportation borne by the customer.

In no event shall Norton Construction Products be liable for

consequential or incidental damages arising out of the failure of any

product to operate properly.

Integral units such as gasoline engines, electric motors,batteries,

tires, transmissions, etc., are excluded from this warranty and are

subject to the prime manufacturer's warranty.

This warranty is in lieu of all other warranties, expressed or implied,

and all such other warranties are hereby disclaimed.

Important: Before placing equipment in operation, record the following

information.

MODEL: _________ SERIAL NO.: ___________

PURCHASE FROM: _____________________

ADDRESS: ____________________________

CITY: _______ STATE: ______ ZIP: ________

TELEPHONE NO. ______________________

Before using this equipment, make sure that person using it

Read and understand the instructions in this owner’s manual.

Table of Contents

Section Page

I. Preparation

A. Safety Precautions 3

Dust and Silica Warning 4

B. Assembly 5

C. Assembly Conveyor Cart & Guide a Cut 5-6

D. BBL Series Masonry Saw Specifications 7

E. Electrical Connections 8

F. Wiring Diagram 9

G. Gasoline Engine 11

II. Operation

A. How To Mount The Blade 12

B. “Step Cutting” With Abrasive Blades 13

C. “Jam Cutting” And “Step Cutting With Diamond Blades 13-14

D. Dry Cutting 15

E. Wet Cutting 15

III. Maintenance

A. V-Belts 15-16

B. Motor/Engine 16-17

C. Blade Shaft Bearings 17-18

D. Pump 18

IV. Parts List

A. Ordering Information 18

B. Parts List 19-28

C. Engine/Motor Service Policy Information 29-30

Read Owners Manual Before Use

Safety Alert Symbol: Information Following This Symbol Is Very

Important.

Use Only Genuine Norton Diamond Blades

I. PREPARATION

A. Safety Precautions

Important! The following safety precautions must always be observed.

Hazard Symbols

Fuel (gasoline) is extremely flammable and its vapors can explode if

ignited. Store gasoline only in approved containers, in well-

ventilated, unoccupied approved areas, and away from sparks or

flames. Do not fill the fuel tank while the engine is hot or running.

Do not start the engine near spilled fuel.

Never use the fuel as a cleaning agent

Engine components can get extremely hot from operation. To

prevent burns, do not touch the engine or related parts while the

engine is running or immediately after it is turned off. Never

operate the engine with any heat shields or guards removed.

Keep all guards in place when operating any piece of equipment

Keep hands, feet, hair, and clothing away from all rotating parts

Lethal Exhaust Gas use only in well ventilated areas. Engine

exhaust gases contain poisonous carbon monoxide, which is

odorless, colorless, and can cause death if inhaled. Avoid inhaling

exhaust fumes, and never run the engine in a closed building or

confined area

Never tamper with the governor components of settings to increase

the maximum speed. Severe personal injury and damage to the

engine or equipment can result if operated at speed above

maximum. Always obey the maximum speed rating of blade.

DO NOT LIFT THE SAW BY THE HANDLE

Dust and Silica Warning

Grinding/cutting/drilling of masonry, concrete, metal and other materials can

generate dust, mists and fumes containing chemicals known to cause serious or

fatal injury or illness, such as respiratory disease, cancer, birth defects or other

reproductive harm. If you are unfamiliar with the risks associated with the

particular process and/or material being cut or the composition of the tool being

used, review the material safety data sheet and/or consult your employer, the

material manufacturer/supplier, governmental agencies such as OSHA and

NIOSH and other sources on hazardous materials and make certain to comply

with all product warnings and instructions for the safe and effective use of the

material being cut. California and some other authorities, for instance, have

published lists of substances known to cause cancer, reproductive toxicity, or

other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use

good work practices and follow the recommendations of the manufacturer/supplier,

OSHA/NIOSH, and occupational and trade associations. Water should be used

for dust suppression when wet cutting is feasible. When the hazards from

inhalation of dust, mists and fumes cannot be eliminated through engineering

controls such as either vacuum and/or water mist, the operator and any

bystanders should always wear a respirator approved by NIOSH/MSHA for the

material being cut.

Use Approved:

Eye Protection Hearing

Protection Respiratory

Protection Head Protection

I. PREPARATION

B. Assembly

1. Remove machine from skid.

2. Remove the conveyor cart and guide-a-cut from the carton and place on the

pan.

3. Remove the drain plug from carton and place in drain opening in bottom of

pan.

4. Check the owner’s manual for wiring connection and proper electrical

connections before starting saw.

C. Assembly Conveyor Cart & Guide-a-Cut

The Block Buster Masonry saws are shipped completely assembled and ready

for use except for diamond blade, gasoline, and oil. Inspect the saw for

shipping damage. If any damage is found, contact the shipper immediately

and file a freight claim. The Norton Company is not responsible for

any freight-related damages. Remove the saw from the pallet.

Items Included with the saw:

Item Part Number QTY

Conveyor Cart Assembly 83777 1

Guide-A-Cut Assembly 83892 1

Splash Guard Assembly 75128 1

Wrench 19 mm 70807 1

Wrench 22mm 72143 1

Water Pump Assembly 72305 1

Do not install the blade until it is time to use the saw!

ANSI regulations prohibit the transportation of any concrete saw with

the blade installed!

I. PREPARATION

C. Assembly Conveyor Cart & Guide-a-Cut

Conveyor Cart Assembly:

Remove the Conveyor Cart and Back Stop from the Saws Water Pan, and the

Wing Nuts, Carriage Bolts, Washers, and Cart Stop from the plastic bag. Slide

one (1) Carriage Bolt thru each of the three (3) Square Holes located on the

front of the Conveyor Cart. Slide the Back Stop Over each of the Carriage

Bolts. Slide the Stop Assembly over the Carriage Bolt Located on the Left front

of the Conveyor Cart NOTE: The Rubber Stop will faces away from the

Conveyor Cart. Attach one (1) Washer and one (1) Wing Nut to each Carriage

Bolt and Tighten. See Figure 1: Back Stop Assembly. Place the Conveyor

Cart on the Machine.

Figure 1: Back Stop Assembly

Guide-A-Cut Assembly:

Attach the Guide-A-Cut to the Conveyor Cart by adjusting the Wing Bolt until

the Guide-A-Cut can slide over the Black Stop. The Guide-A-Cut will work as a

Rip Guide that is adjustable for 90and 45cuts. See Figure 2: Guide-A-Cut

Assembly.

Figure 2: Guide-A-Cut Assembly

Splash Assembly:

Remove the Splash Guard from the Saw Water Pan. Attach the Splash Guard

Spring Clips to the Pivoting Bar Located Under the Cutting Head. Note that the

rough side of the Splash Guard should face towards the front of the saw. The

Splash Guard material is made is designed for easy to cleaning. To clean,

simply rinse the Splash Guard with water until clean. The Splash Guard should

be used when wet cutting to reduce the amount of debris thrown from the blade

and cutting surface. When dry cutting the Splash Guard can be removed to

allow the dust particles to drift away from the Saw Operator.

I. PREPARATION

D. BBL Series Masonry Saw Specifications

Dimensions/Weight

Length 41” (1041mm)

Width 26” (660mm)

Height (Electric) 54” (1372mm)

Height (Gas) 57” (1448mm)

Weight (Electric) Uncrated 440lbs (970kg)

Weight (Gas) Uncrated 460lbs (1014kg)

Electric Motor

Motor Mfg. Baldor

Motor Type TEFC, Thermal Protection

Motor RPM 3450

BBL527 & BBL547 5 HP - 230v 60 Hz single Phase (Standard)

230-460v 60Hz three Phase (Optional)

5 HP Run Amp 20.6 Amp @ 230v

BBL727 & BBL747 7-1/2 HP 230-460v 60Hz three Phase

7-1/2HP Run Amp 8.4 Amp @ 230v

Engine

Engine Mfg. Honda

Spec No. GX390K1QXC9

Model GX390

Engine Type Single Cylinder 4 Cycle

Horse Power 13 hp (9.5kW) @ 3,600 rpm

Max Torque 19.5 ft-lbs (26.5 Nm, 2.7 kg-m) @ 2,500 rpm

Cooling System Air

Oil Capacity 1.1 liter (1.16 US qt)

Fuel Capacity 6.5 liter (1.79 US gal)

Fuel Type Unleaded Gasoline (86 pump octane)

Low Oil Sensor Yes

Air Filtration Four Stage Cyclone

Characteristics

Max Blade 20” (508 mm) or 14” (356 mm)

Depth of Cut 24” (610 mm) 10” (254 mm)

20” (508 mm) 8” (203 mm)

14” (356 mm) 5” (127 mm)

Arbor Bore 1” (25.4 mm)

Blade Shaft Locking Device Machined Into Flats Of Tight Collar

Blade Shaft Speed 24” 1938 rpm

20” 2400 rpm

14” 2900 rpm

Depth Control Hand Feed With Return Spring

Depth Lock Standard

Number Of V-Belts 2

Blade Guard Type All Steel Construction

Stay Level Blade Guard Yes

Fork Lift Brackets Built In

Water Pump Standard, Mechanically Belt Driven

I. PREPARATION

E. Electrical Connections

Important Before connecting the motor leads to the power supply, be sure that

the voltage, cycles and phase shown on the nameplate of the motor correspond to

the available power supply.

Both the 5 h.p. and 7-1/2 h.p. motors have overload protectors and are equipped

with a reset button on the motor housing. If, after proper electrical connections are

made, the motor will not run, press the reset button to the overload protector

switch.

Voltage Selection for Single Phase Motors 3 h.p. Single phase masonry saw

motors have' an * optional dual voltage switch so that 115 volt or 230-volt power

supply can be used with no change in wiring. Wherever possible, use 230 volt

power supply for best operation. To change voltage, remove the screw on the

motor voltage toggle switch, and set the toggle switch knob to the connected

operating voltage .

Power Connections

Connect the power supply to the pigtail leads of the switch. Direct wiring

connection is preferred, but an extension cord with an electrical plug with 30 amp

minimum capacity may be used. Connecting wires should be as short as possible

and in one piece. In no case should the connecting wires be longer than shown in

the following table for 3 and 5 h.p. single phase motors:

Length Of Wire

Wire Gauge 3 HP 115-Volt 3 &5 HP 230-Volt

12 -NA- 50’

10 25’ 100’

08 50’ 150’

06 75’ -NA-

Caution-When wires that are too small gauge or too long are used, loss of power,

over heating, or possible damage to the motor will result.

I. PREPARATION

F. Wiring Diagram 5HP 230v single Phase

For any Electric Motor service, warranty, or technical related questions contact your nearest

Baldor service center:

Baldor Electric Company

Corporate Headquarters

5711 R.S. Boreham, Jr. St.

P.O. Box 2400

Fort Smith, AR 72901

Phone: (501) 646-4711

Fax: (501) 648-5792

Autres manuels pour BBL547

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Norton Scie

Norton

Norton TT 200 EM Manuel utilisateur

Norton

Norton CM 351 Manuel utilisateur

Norton

Norton BBL547 Manuel utilisateur

Norton

Norton clipper TT 251 Manuel utilisateur

Norton

Norton clipper CS 352 Manuel utilisateur

Norton

Norton clipper CM 350 B Manuel utilisateur

Norton

Norton Clipper TR 202 Manuel utilisateur

Norton

Norton clipper TR 231 GL Manuel utilisateur

Norton

Norton Clipper C1318P Manuel utilisateur

Norton

Norton Clipper TR 232 S Manuel utilisateur

Norton

Norton Clipper C13PE Manuel utilisateur

Norton

Norton BBL547 Manuel utilisateur

Norton

Norton clipper CS 352 B Manuel utilisateur

Norton

Norton Clipper CS 401 P13 Manuel utilisateur

Norton

Norton Clipper CB 311 Manuel utilisateur

Norton

Norton Clipper CTC1020XL Manuel utilisateur

Norton

Norton TR 230 GL Mode d’emploi

Norton

Norton clipper CHW Series Manuel utilisateur

Norton

Norton TC-405 Manuel utilisateur

Norton

Norton JCW 600 Manuel utilisateur

Norton

Norton GC55 Manuel utilisateur

Norton

Norton TR 230 GS Manuel utilisateur

Norton

Norton Clipper CMV 1000 Verto Manuel utilisateur

Norton

Norton CGW 1.30.1 230V Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur