If in doubt,use larger cord.
Be sure tocheck voltage requirementsof the toolto your incomingpower source.
· Do not exposethe sharpener torain or wetconditions. Waterentering the sharpenerwill increase therisk of electricshock.
· Do not letyour fingers touchthe terminals ofplug when installingto or removingfrom the outlet.
· Ground fault circuitinterrupters. If workarea is notequipped with apermanently installed GroundFault Circuit Interrupteroutlet (GFCI),
use a plug-inGFCI between powertool or extensioncord and powerreceptacle.
PERSONAL SAFETY
· Stay alert, watchwhat you aredoing and usecommon sense whenoperating the shapener. Do notuse the toolwhile you aretired or
under the influenceof drugs, alcoholor medication.A momentof inattention whileoperating power toolsmay result inserious personal
injury.
· Dress properly. Do notwear loose clothing,dangling objects, orjewelry.Keep your hair, clothing andgloves away frommoving parts.
Loose clothes, jewelryor long haircan be caughtin moving parts.Air ventsoften cover movingparts and shouldbe avoided.
· Use safety appareland equipment. Usesafety goggles orsafety glasses withside shields whichcomply with currentnational standards,
or when needed,a face shield.Use as dustmask in dustywork conditions.This applies toall persons inthe work area.Also usenon-skid
safety shoes, hardhat,gloves, dust collectionsystems, and hearingprotection when appropriate.
· Avoid accidentalstarting. Ensure theswitch is inthe offposition before pluggingtool into poweroutlet. In theevent of apower failure,
while a toolis being used,turn the switchoff toprevent surprise startingwhen power isrestored.
· Do not overreach.Keep proper footingand balance atall times.
· Remove adjusting keysor wrenches beforeconnecting to thepower supply orturning on thetool. Awrench or keythat is leftattached to
a rotating partof the toolmay result inpersonal injury.
TOOL USEAND CARE
· Do not forcethe sharpener.Toolsdo a betterand safer jobwhen used inthe manner forwhich they aredesigned. Plan yourwork,
and use thecorrect tool forthe job.
· Never use asharpener with amalfunctioning switch.Any tool thatcannot be controlledwith the switchis dangerous andmust be
repaired by anauthorized service representativebefore using.
· Disconnect power fromsharpener and placethe switch inthe locked oroff position beforeservicing, adjusting, installing
accessories or attachments,or storing.Such preventive safetymeasures reduce therisk of startingthe power toolaccidentally.
· Store idle sharpeners.When tools arenot in use,store them ina dry, secure placeout of thereach of children.Inspect tools for
good working conditionprior to storageand before re-use.
· Use only accessoriesthat are recommendedby the manufacturerfor your model.Accessories that maybe suitable forone tool
may create arisk of injurywhen used onanother tool.
· Never touch themoving grinding wheel.
· The sharpener's motoris specially ratedfor intermittent use 15 minutes continuoususe.
· Do not attachmodules when thegrinding wheel ismoving.
· Do not usethe grinding wheelwithout a modulein place.
· Keep guards inplace and inworking order.
OPERATION
Sharpens all highspeed steel drillbits from 7/64"(3mm) to
3/8" (50mm)
Unique "TruePoint" action ensuresaccurate finish
Precisely locates highspeed steel drillsfor correct sharpening
angles
Re-sharpen broken drillbits
SHARPENING HSS BITS
1.Slide module,labeled High SpeedSteel Drill Sharpener, on
to the PowerUnit.
2.Remove theclamp holder andinsert the drillbit to besh
arpened (1a).Tighten theclamp lightly toleave the drillbit
still free tomove.
3.Place theclamp containing yourdrill bit intothe setting slot,
using the groovesin the sideto lower itin correctly (1b).
4.Move thedrill bit forwardup so thatit lies inthe V-guideand
touches the metalend stop (1c).
5.Turnthe drill bituntil the V-guide fully dropsover it (1c) all
for drill bitcorners should nowbe touching theV-guide sides.
6.Ensure thatthe drill andholder are fullydown in thesetting
Slot. With thedrill bit inthis position, tightenthe clamping ring(1d).
7.Lift upthe V-guideand remove theclamp and drillbit.
8.Transferthe clamp anddrill bit intothe clamp holderon the
Power Unit modules(1e).
9.Switch thePower Unit on.
10.Move theclamp holder fromside to side,securing with lightfinger
Pressure (1f).
11.Remove the drillbit and holderand turn over(1g). Repeat stepNo. 11.
12.Check thatthe leading edgeof both flutesare equally sharp.They shouldmeet exactly inthe middle asin (1h), not(1i).
13.Switch thePower Unit off. Before removingthe module, ensurethe grinding wheelhas stopped.
· Before removing amodule, switch powerOFF,allow grinding wheelto come toa complete stopand unplug themachine.
·
· Never sharpen morethan one itemat a time.
Do not jamthe workpiece againstthe sharpening surface.Firmly grasp the workpiece and easeit against thesharpener using light
pressure.
2 OF 5
