NookBox P119010 Manuel utilisateur

NookBox Installation Guide Keypad

NookBox Keypad

(P119010 / E6309744)

Installation Guide

NookBox Installation Guide Keypad

NookBox Keypad

(P119010 / E6309744)

NookBox Installation Guide Keypad

Parts Identication

1. Active LED

2. Status LED

3. Fault Display LED

4. Arm Key

5. Home Key

6. Key

• Check Control Panel Status

7. Disarm Key

8. # Key

9. *Key

• Enter KP Pin Code + *Key to enter Test Mode

10. Dual Key Learning

• Press both #and *keys together to send learn Code

11. Medical Alarm (if enabled)

• press both 7 and 9 to trigger medical alarm

12. Fire Alarm (if enabled)

• press both 4 and 6 to trigger re alarm

13. Panic Alarm (if enabled)

• press both 1 and 3 to trigger panic alarm

14. Battery Insulator

15. Mounting Holes

16. Tamper Swtich

<NOTE>

• A short beep will sound along with key pressing to indicate that the button pressed is valid.

• 4 continuous beeps will sound indicating mistake and the user should repeat the process again.

NookBox Installation Guide Keypad

LED Indicator

Active LED (Blue/Amber)

• Blue LED on 5 seconds: the system is in Normal Operation Mode.

• Blue LED ashes for 5 seconds: low battery in Normal Operation Mode.

• Amber LED on: the system is in Test Mode.

• Amber LED ash: low battery in Test Mode.

<NOTE>

• Active Blue LED will turn on at any key press, after successful completion of a valid keystroke sequence, or when the keypad idles for 5 seconds.

• When the Active Blue LED turns o before a valid keystroke sequence is completed, the previous entered keys are ignored.

Status LED (Blue/Red):

• Red LED on: the system is in Away Mode.

• Red LED ash: the system is in Home Mode.

• Blue LED on: activation of Disarm Mode.

• Blue LED ash: failure due to the following reasons:

» No response sent by the control panel within 4 seconds.

» Control Panel User PIN code was incorrect.

» Request for Home mode during Arm mode.

» Request for Force arm.

Fault LED (Amber):

• Flash: system failure (panel tamper, AC fault, sensor temper, sensor out of order, open door)

• On: Alarm Memory (depend on Control Panel).

NookBox Installation Guide Keypad

Power

• Remote keypad uses one CR2 3V Lithium battery as its power source.

• Remote keypad can also detect the battery status. If the battery voltage is low, the Active LED will ash (Amber in Test mode or Blue

in Normal mode) during operation. The Low battery signal will be sent along with regular signal transmissions to the Control Panel for

displaying the status accordingly.

• Before shipment, the battery is pre-installed by the factory.

• When changing battery, press the any key a couple times to discharge before inserting new battery.

Power Saving Feature

• When idle, Remote keypad is in Stand-by mode and uses no power. It will activate and wake-up for 5 seconds when any key is pressed.

• After 5 seconds of key inactivity, the power goes o and it returns to Stand-by mode.

• Upon completion of a command input, the power goes o and Remote keypad returns to Stand-by mode.

Test Mode

• Remote keypad can be put into Test mode by entering the Keypad PIN code (default: 0000) followed by * key. The Active Amber LED

will turn on along with a long beep.

• To exit Test mode, press key twice, Remote keypad will sound a long beep and the Active LED will turn o, then Remote keypad

returns to Normal Operation mode. Otherwise, Remote keypad will automatically exit Test mode after 5 minutes and return to Normal

Operation mode.

<NOTE>

• When Remote keypad is in Test mode, it operates as wake-up condition and will NOT disconnect after 5 seconds.

Test Mode Function:

» Press *key and then 7key — Transmit Remote keypad learn signal

» Press *key and then 2key — Enable Dual-key Panic Alarm function

» Press *key and then 3key — Enable Dual-key Fire Alarm function

» Press *key and then 4key — Enable Dual-key Medical Alarm function

» Press *key and then 5key — Disable all Dual Key function (Default)

» Press *key and then 6key — Edit Keypad Pin Code

Enter Old Keypad Pin Code and then press key

Enter New a new 4-digit Keypad Pin Code and then press #key.

» Press key twice — to leave the Test Mode.

» Press *key and then 8key — Enable Arm/ Home without PIN Code function

» Press *key and then 9key — Enable Arm/ Home with Control Panel User PIN Code function (Default)

Tamper Protection

• The keypad is protected against any attempt to open the lid or to detach keypad from its mounting surface.

• Tamper protection is disabled when the keypad is in Test Mode.

NookBox Installation Guide Keypad

Installation Procedures

Step 1. Put the Control panel into learning mode.

Step 2. Adding remote keypad into the Control Panel:

Test Mode Learning:

1. Put remote keypad in Test mode by entering KP PIN code (default: 0000), then press *key. The Active Amber LED will

turn on along with a long beep sound.

2. Press

*key then 7key. Remote keypad will sound a long beep.

<NOTE>

• If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning code to the Control Panel, please

press

*key then 7key again to send the learning code.

3. If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation manual of your

Control Panel to complete the learn-in process.

4. After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote keypad. The

remote keypad will then beep 3 times to conrm the acknowledgement has been received.

Dual-Key Learning:

1. Press and both #and *keys together under Normal Operation Mode. Remote Keypad will sound a long beep.

<NOTE>

• If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning code to the Control Panel, please

press both # and *keys together again to send the learning code.

2. If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation manual of your

Control Panel to complete the learn-in process.

3. After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote keypad. The

remote keypad will then beep 3 times to conrm the acknowledgement has been received.

• If remote keypad does not perform 3 beeps, please restart the learning procdeure.

Step 3. After the Remote keypad is learnt-in, put the Control Panel into Walk Test mode, hold the Remote keypad in the desired

location, and send the learning code to the Control Panel to conrm this location is within the signal range of the Control Panel.

To send the learning code, either press the *key then 7key under Test Mode or press both #and *keys together under

Normal Operation Mode.

Step 4. When you are satised that the Remote keypad works in the chosen location, you can proceed with mounting the Remote

keypad following the steps described below (see Mounting Remote keypad).

Step 5. Set your own the KP Pin Code:

1. When the keypad is under Test mode, press *key then 6key, a long beep will be sound.

2. Enter 0000 (default PIN code)

3. Press key, remote keypad sounds a long beep.

4. Enter your new 4-digit code.

5. Press #key, remote keypad sounds a long beep. The new PIN code is enabled.

Step 6. Press key twice to leave Test mode and the installation is completed.

NookBox Installation Guide Keypad

Mounting Remote Keypad

To mount the remote keypad:

1. Remove the front cover.

2. Using the 2 mounting holes of the back cover as a template, mark o the positions in the most appropriate place.

3. Insert the wall plugs if xing into plaster or brick surface.

4. Screw the Remote keypad onto the wall plugs.

5. Replace the front cover.

System Mode Control

After nish learning the Keypad into alarm system Control Panel, the user may change the system using Keypad.

There are two ways to arm the system.

1. Away Arm / Home Arm the system by entering Control Panel User PIN Code.

2. Away Arm / Home Arm the system without entering Control Panel User PIN Code.

Disarming the system always requires entering Control Panel User PIN Code.

KP-23B-F1 model Keypad supports both 4-digit and 6-digit PIN Code.

KP-23B model Keypad only supports 4-digit PIN Code

Arm/Home with Control Panel PIN Code

Under Test mode, Pressing *key and then 9key to enable Arm/ Home with PIN Code function (Default).

» Enter Arm Mode: Enter any one of Control Panel user code and press key. If panel has no fault and arming is successful, the

Status Red LED will turn ON alone with a long beep.

» Enter Home Mode: Enter any one of Control Panel user cods and key. If panel has no fault and arming is successful,

the Status Red LED will ash 4 times alone with 3 beeps.

» Return to Disarm Mode: Enter any one of Control Panel user code and key. If disarm is successful, the Status Blue LED will turn ON

along with 2 beeps.

Arm/Home without Control Panel PIN Code

In the Test mode, Pressing *key and then 8key to enable Arm/ Home without PIN Code function

» Enter Arm Mode: Press key. If panel has no fault and arming is successful, the Status Red LED will turn ON alone with one

long beep.

» Enter Home Mode: Press key. If panel has no fault and arming is successful, the Status Red LED will ash 4 times alone with

3 beeps.

» Return to Disarm Mode: Enter any one of Control Panel user code and Key. If disarm is successful, the Status Blue LED will turn

ON along with 2 beeps.

NookBox Installation Guide Keypad

Dual-key Alarm function

» Panic Alarm — Press both 1and 3keys to trigger Panic alarm.

» Fire Alarm — Press both 4and 6keys to trigger Fire alarm.

» Medical Alarm — Press both 7and 9keys to trigger Medical alarm.

<NOTE>

• The dual-key alarm function is disabled by default. To enable it, please refer to the Test Mode section.

General Operation

» If there is Alarm Memory, the Status Blue LED and fault LED will turn ON with 5 beeps (depending on Control Panel).

» Enter Test mode — Enter Keypad PIN code and then press *key.

» Panic Alarm — Press 1key + 3key at the same time. (if the function is enabled)

» Fire Alarm — Press 4key + 6key at the same time. (if the function is enabled)

» Medical Alarm — Press 7key + 9key at the same time. (if the function is enabled)

» Check Control Panel Status — Normal Mode Press key.

• Red LED on: the system is in Away Mode

• Red LED ash: the system is in Home Mode.

• Blue LED on: activation of Disarm Mode.

• Blue ash: failure due to the following reasons:

• No response sent by the control panel within 4 seconds.

• PIN code was incorrect.

• Request for Home mode during Arm mode.

• Request for Force arm.

NookBox Installation Guide Keypad

Fault Conditions

When Remote Keypad is under NORMAL OPERATION MODE,

a) When fault condition exists within Control Panel, if the Keypad is used to arm the panel, the keypad Status Blue and Fault Amber LED

will ash 4 times along with 3 beeps to indicate fault condition.

User can force arm the Control Panel by performing the arm action again.

b) When the Keypad disarms the panel, the Active Blue LED will turn ON alone with two short beeps indicating normal operation.

At a fault situation, it will emit 5 times and turn on both Status Blue and Fault Amber LED for 5 seconds.

c) If the Control Panel is under Arm Mode, you CANNOT activate Home mode with Remote keypad. The Status Blue LED will ash

4 times to indicate transmission error.

d) If you input incorrect KP Pin code for 4 times, KP will disable the key function for 1 minute and ash all LEDs ashing 3 times with 6 beeps.

After 1 minute, it will emit a long beep to indicate that the key function is back to normal.

Factory Reset

Resetting the Keypad to factory default will restore Keypad’s own PIN Code to 0000 and clear all panel learning memory.

Reset to factory default:

Step 1 Remove the batteries and release the tamper.

Step 2 Press & hold 3key while inserting the battery back.

Step 3 Continue pressing 3until three short beeps to indicate successful reset.

Step 4 Release 3key, the reset process is complete.

After reset, PIN code reverts to factory default values, 0000. Remote keypad will need a new learn-in process to start functioning.

NookBox Installation Guide Keypad

For more information visit:

www.getnookbox.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NookBox Clavier

NookBox

NookBox KP-35 Manuel utilisateur

Manuels Clavier populaires d'autres marques

BFT

BFT SELETTO Manuel utilisateur

Micro Id

Micro Id MP7G3BL Manuel d'instructions

WindowMaster

WindowMaster WLI 130 Manuel utilisateur

ACT

ACT ACT PRO 1030 Manuel utilisateur

Cardin

Cardin SSB Series Manuel utilisateur

Harman Kardon

Harman Kardon KP 1 Manuel utilisateur

Chamberlain

Chamberlain KPR2000 Guide de l'utilisateur

CYP

CYP CR-KP1 Manuel utilisateur

Aeware

Aeware k-35 Series Guide de référence

Aritech

Aritech CS-175 Series Manuel utilisateur

GE NetworX NX-1600E Series Manuel utilisateur

Lenze AC Tech

Lenze AC Tech MC SERIES Manuel utilisateur

Burg Wächter

Burg Wächter secuENTRY 7711 Manuel utilisateur

Aeware

Aeware in.k450 Manuel utilisateur

Lenze

Lenze EPM-H410 Manuel utilisateur

Toshiba

Toshiba RKP007Z Manuel utilisateur

Gemini

Gemini GEM-DXK1 KEYPAD Manuel utilisateur

Russound

Russound MDK-C5 Manuel d'utilisation