Nokia MW1122 Manuel utilisateur
Nokia MW1122
T66520
USER MANUAL
ADSL/WLAN Routerā
ECopyright Nokia Networks Oy
C33902002SE_00 1
MW1122
ADSL/WLAN Router
User Manual
05.07.2000
C33902.21A0
1 Introduction to Nokia MW1122
Nokia MW1122 is an integrated ADSL (Asymmetric Digital
SubscriberLine) bridge and router which enables high-speed Internet
access from your wireless (WLAN) and Ethernet local area networks
(LAN). It multiplies the capacity of the already installed telephone
lines used traditionally for telephone and dial-up modem services.
MW1122 brings high-speed connections available for home users,
small offices and telecommuters.
Figure 1 Nokia MW1122
MW1122 User Manual
ECopyright Nokia Networks Oy C33902002SE_00
2
2 Installing MW1122
BeforeyouinstallMW1122youmaywanttofamiliariseyourselfwith
the interfaces and indicator lights of MW1122. From section 2.3 you
will find a step-by-step installation procedure, which shows the
physical installation of MW1122.
2.1 Interfaces
MW1122 has one ADSL line interface and two LAN interfaces:
WLAN and ETH (wireless LAN and 10Base-T Ethernet). It also has a
local management interface (CLI) for management purposes. The
ADSL line interface is compatible with ITU-T G.992.1 specification.
The wireless LAN port interface supports Nokia’s 11 Mbit/s IEEE
802.11b WLAN PC Card.
ADSL line
Ethernet
WLAN (PC card)Local management interface
Mains connector
Power switch
Figure 2 MW1122 back panel
2.2 Indicator lights
MW1122 has six indicator lights on the front panel: PWR, STA,
WLAN, COL, ETH, and DSL. STA indicator is red. Other indicators
are green.
ECopyright Nokia Networks Oy
C33902002SE_00 3
Figure 3 MW1122 front panel indicators
DSL GREEN
Off ADSL link is down.
Blinks ADSL connection is being established.
On ADSL link is up.
ETH GREEN
Off Ethernet is down.
On 10Base-T Ethernet is functional
Blinks Receives traffic from Ethernet.
COL GREEN
Blinks Collisions on the Ethernet. Note, that it is normal that some
collisions occur on the Ethernet.
WLAN GREEN
Off No stations on the WLAN or WLAN PC Card not
inserted.
On Stations on the WLAN but no traffic.
Blinks Receives traffic through the WLAN interface.
MW1122 User Manual
ECopyright Nokia Networks Oy C33902002SE_00
4
STA RED
Off OK
On Hardware malfunction during startup.
PWR GREEN
Off Power off.
On Power on.
2.3 Step-by-step installation procedure
1. Plug the mains power cord to a mains outlet.
2. Plug the antenna into the antenna connector of the wireless LAN
card, if included.
3. InsertthewirelessLANcard,ifincluded,gentlyintotheMW1122
WLAN slot on the MW1122 back panel. Ensure that the card is
aligned correctly.
4. Switch on MW1122. The PWR indicator lights up.
5. Ensurethat wireless LAN clients (thatis, the wireless devices you
want to use in your network) have the same configuration as the
wirelessLANcardintheMW1122modemandthattheyareinthe
Infrastructure mode. The default wireless LAN configuration of
MW1122 is the following:
regulatory-domain according to your location of use (Europe,
Canada, USA, or Japan)
network name MW-wxyz(case-sensitive),where wxyz are
the last four numbers from your MW1122
serial number
When you have set the network name to your wireless client, the
wireless connection is established and the WLAN indicator on
MW1122 fron panel will be lit.
6. Connect the 8-pin Ethernet cable between your PC and the
Ethernet connector on the MW1122 back panel if you want use a
PC equipped with a 10Base-T Ethernet card. Switch on your PC.
The ETH indicator will be lit.
ECopyright Nokia Networks Oy
C33902002SE_00 5
7. Connect the 6-pin ADSL line cable between the ADSLconnector
on the MW1122 back panel and your ADSL line wall socket. If
you want to use telephone and data services simultaneously
connect a splitter according to Figure 4. After a while, the DSL
indicator starts blinking indicating that the ADSL connection is
being established. After the connection has been established
successfully the DSL indicator remains lit.
splitter
Figure 4 MW1122 and splitter connected
Now, your MW1122 has been connected and you can check the
connections according to your service provider’s instructions.
3 Configuring MW1122
Your service provider has configured your MW1122 for the service.
However,youmaywanttochangethesettingsregardingyourwireless
network.YouwillfindthesesettingsontheWirelessLANandWLAN
Clients web pages. Do not change other settings unless specifically
asked by your service provider. You can change MW1122 settings
with an ordinary web browser such as Microsoft Internet Explorer or
Netscape Navigator.
If the WLAN indicator is lit on the MW1122 front panel, you can use
yourWLAN client for configuration. Ofcourse,youcanalsouseaPC
MW1122 User Manual
ECopyright Nokia Networks Oy C33902002SE_00
6
connectedtotheETH port of MW1122.In this casethe ETH indicator
should be lit.
3.1 Browser management
You can use your PC’s web browser software to access the web
configuration pages in MW1122. To access the web pages you must
knowtheIPaddressofyourMW1122or,alternatively,the“name”that
your MW1122 recognises.
Note
Before using your web browser for configuration, you must know the
IP address or the name assigned to your MW1122.
There are three ways to find out whether to use a name or an IP
address:
DYour service provider has given you an IP address for MW1122.
DYour MW1122 uses Dynamic Host Configuration Protocol
(DHCP) and Domain Name Server. In this case the name is
MW1122.
DYour MW1122 uses DHCP. In this case run winipcfg.exe
(Windows 95) or ipconfig.exe (Windows NT). The IP address of
MW1122 is the Default Gateway address shown by the ipconfig
program.
3.1.1 Opening a connection
To open a connection to the Nokia MW1122:
1. Start your web browser.
2. Enterthename(’MW1122’)orIPaddressofyourNokiaMW1122
in the browser’s Location or Address field and press Enter.
3. Type in the username/password as requested. If no
username/password is required, just click OK to proceed. The
Nokia MW1122 Main Page appears.
ECopyright Nokia Networks Oy
C33902002SE_00 7
3.1.2 Main Page
Main Page is shown first when you use a web browser to connect to
MW1122.The list on the left shows the current page highlighted.
Clicking an item on the list (Wireless LAN, WLAN Clients, Service
Providers, Local Network, Statistics, Restart, and Save Config) takes
youtothecorrespondingpage.Typically,youwillonlyhavetochange
the Wireless LAN and WLAN Clients settings.
Note
Whenyoumake modifications to the configuration, remembertosave
the configuration and restart your MW1122 for your changes to take
effect.
Figure 5 Main Page
MW1122 User Manual
ECopyright Nokia Networks Oy C33902002SE_00
8
The Main Page shows you the statuses of the DSL line, Ethernet
interface, and wireless LAN interface. It also shows the number of
wireless LAN clients on your network, wireless LAN network name
and the channel in use. Software and hardware versions and the serial
number of MW1122 are shown in the bottom of the page.
3.1.3 Wireless LAN page
You can change wireless LAN network settings on the Wireless LAN
page.
Figure 6 Wireless LAN page
Note
When you click the Apply button, the WLAN subsystem will be
reseted automatically. If you have changed the network name and you
are accessing MW1122 through the wireless connection, the wireless
link will be disconnected. You must reconfigure the network name to
your wireless LAN client to continue configuration. The Reload
buttonrestoresthesettingsifyouhavenotsavedtheconfigurationyet.
Network name identifies your network and must be the same in all
wireless LAN clients on your network. The default network name is
MW-wxyz (case-sensitive), where wxyz are the last four numbers
from your MW1122 serial number.
ECopyright Nokia Networks Oy
C33902002SE_00 9
Set Regulatory domain according to your location of use. The
Regulatory domain setting affects the available Radio channels. The
radio channels corresponding to the regulatory domains are:
Europe 1...13
Canada 1...11
USA 1...11
Japan 14
ChangeTransmitpowerifyourwirelessnetworkbecomesweakonthe
edges.
Autres manuels pour MW1122
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Nokia Routeur sans fil
