Nokia 1265 Mode d’emploi
Nokia Customer Care
1265 (RH-103)
Mobile Terminal
Antenna Description and
Troubleshooting
Issue04/2007 CompanyConfidential ©2007 Nokia Corporation
1265 (RH-103)
Antenna Description and Troubleshooting
Contents Page
Introduction............................................................................................................... 3
Visual Quality Requirements.............................................................................3
Failures and Corrective Measures........................................................................... 3
PIFAAntenna.....................................................................................................4
Damaged RF feed point or Ground Pad............................................................4
Damaged IHF Speaker Spring Pins...................................................................5
Obstructed Speaker, RF feed point, and Ground pads ........................................... 5
Grounding of Display Frame..............................................................................6
RF Connector Failure........................................................................................7
Page 2 ©2007 Nokia Corporation Company Confidential Issue 04/2007
1265 (RH-103)
Nokia Customer Care Antenna Description and Troubleshooting
Introduction
The mobile terminal incorporates an internal antenna. This antenna arrangement is
used for Cellular frequency bands. The internal antenna assembly adopts Planar
Inverted-F Antenna (PIFA) structure used for the cellular engine.
Visual Quality Requirements
Following are the minimum acceptable visual quality requirements of the internal
antenna assembly:
zWear gloves to assemble the antenna. Don’t touch the antenna radiator
with bare hands.
zNo visual cracks or mechanical defects.
zNo oil, dirt, or particles are found on the parts.
zRadiator must be aligned with the plastic housing.
zRadiator must be flat with no warping.
zThe length of all pins must be identical and the pins align.
Failures and Corrective Measures
The internal antenna is assembled into the D Cover Assembly as shown in Figure 1.
If no internal antenna is installed, the antenna gain is degraded by more than 20
dB.
zIf the internal antenna is missing, install SAM Module.
zIf the radiator looks damaged obviously, replace it with a new SAM
Module.
Internal Antenna Holder / Carrie
r
The back of Speaker
Figure 1: D Cover Assembly
Issue 04/2007 ©2007 Nokia Corporation Company Confidential Page 3
1265 (RH-103)
Antenna Description and Troubleshooting
PIFA Antenna
The internal antenna has a planar-inverted F antenna (PIFA) radiator attached to the
plastic carrier. An integrated hand-free (IHF) mini speaker is integrated inside the plastic
carrier.
Figure 2: The top view of internal antenna
Damaged RF feed point or Ground Pad
The two pads of the antenna must properly connect the PWB.
zIf the main antenna’s RF feed pad does not touch the PWB, the antenna
gain degrades by more than 17 dB.
zIf the ground pad of the main antenna does not touch the PWB, the
antenna gain degrades from 0.5 to 1 dB.
zIf either the RF feed pad or ground pad are broken, covered or removed,
such that either pin does not touch the PWB, replace the SAM Module.
zIf either the RF pin or ground pin springs appear damaged, replace the
SAM Module.
RF feed pad
Ground pad
The back of
Speaker
Figure 3: The back view of internal antenna
Page 4 ©2007 Nokia Corporation Company Confidential Issue 04/2007
1265 (RH-103)
Nokia Customer Care Antenna Description and Troubleshooting
Damaged IHF Speaker Spring Pins
In Figure 3, the two contact points on the back of the internal antenna must properly
touch the PWB. If not, no audio signal will emit from the speaker.
Obstructed Speaker, RF feed point, and Ground pads
If any of the RF feed point pad or ground pad is obstructed, removed, or covered,
the antenna pin does not touch the PWB and the antenna performance degrades. If
any of the speaker pads are obstructed, removed, or covered, the speaker’s spring
pins does not touch the PWB and the cellular antenna performance could degrade.
zIf corrosion is present or the pad is missing, replace the PWB.
zIf a pad is obstructed or covered by something, clear and/or clean the
pad.
Speaker pads
Ground pin
RF feed point pin
Figure 4: PWB layout of IHF speaker, RF feed point, and ground pads
Issue 04/2007 ©2007 Nokia Corporation Company Confidential Page 5
1265 (RH-103)
Antenna Description and Troubleshooting
Grounding of Display Frame
The display frame is grounded to the PWB through 2 ground panels. The display
frame grounding needs to touch the PWB. If not, the radio performance will be
impacted.
zIf the clips/tabs do not touch the ground of the PWB, or are corroded, or
are obstructed, replace the LCD Module Shielding Assembly.
Display frame grounding through screw
Display frame grounding through screw
Display frame grounding tabs
Display frame grounding tabs
Figure 5: Display assembly ground points
Page 6 ©2007 Nokia Corporation Company Confidential Issue 04/2007
1265 (RH-103)
Nokia Customer Care Antenna Description and Troubleshooting
RF Connector Failure
The RF connector fails when it does not properly connect the RF input terminal to
the RF output terminal during the SMT. If this happens, the antenna gain degrades
by 25 dB. Check this by testing the resistance value between the RF input and RF
output of the RF connector and see if the value is close to zero. If the RF input is
not connected properly to the RF output, replace the RF connector.
Note: Perform the resistance value test without a RF cable attached to the RF
connector. Because the RF connector is also a switch, the RF output is
disconnected from the RF input when a RF cable is inserted into the RF connector.
zRF input terminal – connect to duplexer.
zRF output terminal – connect to the antenna pad through antenna match
circuit.
zRF connector terminal – connect to a RF coaxial cable.
RF output terminal
Figure 6: RF input / output terminal
RF input terminal
Note:
• QSC6010 is underfilled and cannot be replaced.
• Memory IC is underfilled and cannot be replaced.
• The Shielding Cover cannot be reused after removal.
• After using the heatgun, the domesheet is recommended to be replaced.
Issue 04/2007 ©2007 Nokia Corporation Company Confidential Page 7
1265 (RH-103)
Antenna Description and Troubleshooting
This page intentionally left blank.
Page 8 ©2007 Nokia Corporation Company Confidential Issue 04/2007
Autres manuels pour 1265
5
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Nokia portable
Nokia
Nokia 1265 Guide de démarrage rapide
Nokia
Nokia RH-64 Manuel utilisateur
Nokia
Nokia RM-849 Manuel utilisateur
Nokia
Nokia 301 Manuel utilisateur
Nokia
Nokia 2125 Mode d'emploi
Nokia
Nokia RH-77 Guide de démarrage rapide
Nokia
Nokia 6235 Manuel utilisateur
Nokia
Nokia 2730 Classic RM-579 Manuel utilisateur
Nokia
Nokia RM-506 Manuel utilisateur
Nokia
Nokia 1265 Mode d’emploi
Nokia
Nokia RH-66 Mode d'emploi
Nokia
Nokia RH-66 Mode d'emploi
Nokia
Nokia 7088 Guide de démarrage rapide
Nokia
Nokia RH-66 Mode d'emploi
Nokia
Nokia RM-42 Manuel utilisateur
Nokia
Nokia 6255 Mode d’emploi
Nokia
Nokia 1265 Mode d’emploi
Nokia
Nokia 2255 Manuel utilisateur
Nokia
Nokia RH-77 Mode d'emploi
Nokia
Nokia 3155 Mode d’emploi
