Nokia 3210 Mode d'emploi

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 1 of 37

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 2 of 37

Introduction

IMPORTANT:

This document is intended for use by authorized NOKIA service centers only.

The purpose of this document is to provide some further service information for NOKIA 3210 phones.

It contains a lot of collected tips and hints, to find failures and repair solutions easily.

I will also give support to the inexperienced technicians.

Saving process time and improving the repair quality is the aim of using this document.

We have build it up based on fault symptoms (listed in "Contents") followed by detailed description for further

analysis.

It is to be used additionally to the service manual and other service information

like Service Bulletins, for that reason it doesn't contain any circuit descriptions or schematics.

All measurements are made with using of following equipment:

Nokia repair SW : Wintesla Version 6.10

DLL version : NSE8/9 version 2.41.05

Nokia Module Jig : MJS-13

Digital multimeter : Fluke 73

Oscilloscope : Hitachi V-1565; Fluke PM 3380A

Spectrum Analyzer : Advantest R3361C with an analogue probe

RF-Generator / : Rohde & Schwarz CMD 53

GSM Tester

While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any

errors are found by the reader, NOKIA should be notified in writing, using following procedure:

Please state:

Title of the Document + Issue Number/Date of publication

Page(s) and/or Figure(s) in error

Please send to: Nokia GmbH

Service & Analysis Center Europe

Meesmannstr.103

D-44807 Bochum / Germany

Email: [email protected]

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 3 of 37

Contents

INTRODUCTION 2

DOESN'T SWITCH ON 4

NO FLASH UPDATE POSSIBLE/ DOESN'T SWITCH ON 7

INTERMITTENT DOESN'T SWITCH ON 8

NOT CHARGING 8

LOW STAND BY TIME/ OPERATION TIME 11

PHONE SWITCH IT SELF OFF 13

CONTACT SERVICE COBBA PARALLEL /SERIAL BUS FAIL 15

CONTACT SERVICE-CCONT INTERFACE FAIL 17

CONTACT SERVICE – EEPROM CHECKSUM FAIL 18

CLOCK TIME OR USER SETTINGS PROBLEMS 19

BUZZER FAILURES 20

INTERNAL AUDIO FAILURES 21

DISPLAY FAILURES 23

KEYPAD FAILURE 24

INSERT SIM CARD 25

SIM CARD NOT ACCEPTED, SIM LOCK FAILURE 26

PRODUCT CODE NSE-8 28

RECOMMENDATION FOR REPAIR ACTIONS IN THE RF- AREA 30

LOW RECEIVER SIGNAL STRENGTH INDICATOR 30

NO SERVICE 30

CALL BREAKS / NO SERVICE 33

NO TX-POWER OR TO LOW 34

MEASUREMENT POINTS NSE-8 37

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 4 of 37

Doesn't Switch on

Check VB (Battery 2,4V-3V)

on L102 check connector X101/ X102

change if bend or soiled

Phone doesn't switch on, section: DC / DC converter

check the connection between

L102 and R132 (0 Ohm) Swap the phone if the

connection is open

check solder of V105 or

change if necessary

check the voltage on V101

anode 2,6V; cathode 3,2V

check solder of V105 or

change if necessary

check also R102, R105, R112

DC/ DCconverter is oK!

continue with CCONT

Check 600KHz switching

frequency on Pin 4,5,12,13 of

V105

Check 1,2V operation voltage

on Pin 15 of V105

No No

Yes

Yes Yes

check the solderings and

resistance of L102 "0Ohm" resolder or change L102

check pin 3 from V105

on="low"status 0Ohm

Yes

check V109 and the

respective voltage deviders

R131,132,134,143,144

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 5 of 37

Phone doesn't switch on (CCONT part)

check if PWRON (3,2V DC)

drops to 0V during pressing

the pwr button on R413.

check 32,768KHz, 700mVpp

on B100

check 32.768KHz squarewave

signal on C149

Check PURX (2,8V DC)

afterpressing pwr on button on

R303

Check VXO (2,8V DC) on

C102

change S416 if it is

mechanical broken

change B100 if frquency or

amplitude of the singnal in not

change N100

Check Vbb (2,8V DC)

MAD is faulty in all probability.

Swap the phone, because

MAD is not changeable

Check also C147, C148,

C153

change N100

Check SLEEPX (2,8V DC) on

J340

Check Vref (1,5V DC) on

C123

change N100

check 13 MHz clk frequency

on C301 check 13MHz on G701 check solder of G700 or

change if neccessary

Try to Flash the phone See section :

can't flash the phone

No No

Yes

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 6 of 37

Battery connectors X101/ X102 / bend out dirty

•Check if VBATT and Gnd are connected

Power on/off switch S416 faulty/ mechanical broken

•Check if 3,2V on R413 drops of 0V during pressing the Power on button

L102 poor soldering

•Check the soldering of L102

•Check the resistance in "off mode=0Ω"

•Resolder L102 or change it

N100 CCONT faulty

•Check if 3,2V on R413 drops of 0V during pressing the Power on button

•Check if there is a 32.768 kHz square wave on C149

•Check if PURX on R303 goes up to 2.8 V DC

•Check if VXO on C102 goes up to 2.8 V DC

•Check if VBB on C117 goes to 2,8V DC

•Check if Vref on C123 goes to 1,5V DC

B100 faulty 32,768KHz

•Check 32.768 KHz ; 700mVpp clock signal on B100

•Check also C147, C148, C153

G701 faulty 13 MHz

•Check VCC 2,8V DC on G701

•Check 13 MHz output frequency; 1,2 Vpp on the output pin

VB to R132 board faulty

•Check the battery voltage 2,6V on L102

•Check the same voltage on R132

•Check if the connection from R132 to L102 are 0Ω

•Don't forget to put the additional label on the PCB, it save the layer (see Service Bulletin 11)

D200 MAD faulty

•Check if there is a 32,768 KHz square wave on C149

•Check the 13MHz main clock oscillator on C301 800mVpp

•Check VBB 2,8 V DC on C117

•Check PURX 2,8 V DC on R303 (comes from CCONT)

•Check SLEEPX 2,8 V DC 0n measurement point J 340

•MAD are probable faulty

•MAD are not interchangeable swap the handset

V105 DC/DC converter faulty

•Check the voltage difference on the diode V101 Anode: 2,6V DC, cathode: 3,2V DC

•Check the 600KHz switching frequency on pin 4, 5, 12, 13 from V105

•Check the 1,2V operation voltage on pin 15 from V105

•Check if pin 3 from V105 have low status ≈0V, if not check V109 and the respective voltage dividers R131, R132,

R134, R143, R144

•Change the V105

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 7 of 37

No flash update possible/ Doesn't switch on

Doesn't switch on, section: FLASH (update not possible)

Check 32,768KHz

sleep clock on

C149

Check 13MHz

RFclk on C301

Check VBB 2,8V

continue with

section CCONT

continue with

section CCONT

continue with

section CCONT

"MCU boot failure"

appears during

flashing

"External RAM

error" appears

during flashing

Change the switch

of service frame/

battery to local, if

phone switches

itself off

phone is oK

Try to flash the

phone, if power

consumtion is about

20mA

Change FLASH

and try to update

again

Resolder RAM or

change if

neccessary

try to update again

Swap phone,

because MAD or

PCB should be the

reason

wrong

Yes Yes

same

massage

no massage

wrong

same

massage

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 8 of 37

D301 Flash faulty

•If the handset switches it self off, change the switch of the service frame to local mode

•Check the 32,768KHz Sleep clock signal on C149

•Check the 13MHz main clock oscillator on C301 800mVpp

•Check the VBB voltage on C117

•If power consumption is approximately 20mA try to flash the phone

•If you get a error message during the flashing process, change the flash and try it again

D302 RAM faulty/ poor soldering

•Check if the handset current consumption is approx. 20mA

•Check the 32,768KHz Sleep clock signal on C149

•Check the 13MHz main clock oscillator on C301 800mVpp

•Check the VBB voltage on C117

•Resolder RAM

•Try to flash the handset

•Change the RAM if you get a error message during the flash procedure "external RAM error"

Intermittent doesn't switch on

D301 FLASH faulty

•Check if the handset switches on after reflashing the memory

•D301 Flash internal fail or poor soldering balls

Not charging

Not charging (1)

confirmation or error massage/ beep is not coming from phone if charger ispluged in

Check

V_CHARGE_IN on

C100

Change N101

(PSCC)

check system

connector X503,

clean contacts &

PCB or change if

necessary

not oK

Check resistance

0f fuse (F100) and

L100 (0Ohm)

change if

necessary

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 9 of 37

Do the energy

management

calibration

Check VCHAR on

voltage devider

R100 / R101 (10:1)

=0,8V

Try to charge after

calibration

Change N100

(CCONT)

Check resistance

0f fuse (F100) and

L100 (0Ohm)

change if

necessary

Not charging (2)

error message/ beep is coming from phone if charger is pluged in

Charge voltage

failed

Check R103 if it is

mechanical broken

check voltage

devider R106 /

R111 (1:2)

Check BTEMP A/D

in ADC readings

(317=25°C)

Check the

connection

between R125 and

R127

Battery voltage

failed Cange N100

(CCONT)

Change R103 and

N101 (PSCC)

swap phone if there

is a disconnection

check NTC resistor

R127 (47Kohm)

Check battery

connector X101

X102. change if

bended

failed oK

not oK

Yes oK

not oK

Yes

not oK

CONFIDENTIAL Service & Analysis Center Europe

Training Team

version 1.0 / 05.11.1999 Page 10 of 37

If you are using wintesla NSE8/9 DLL 2.41.03 or lower version the error message "current calibration fail" will

appear in every charge tuning calibration test! See Service manual chapter "service software instructions"

page 19 (Energy Management Calibration)

X503 System connector faulty

•Check the mechanical appearance of the connector

•Clean the contacts on the board or change the connector if necessary

F100 faulty

•Check resistance of F100 (0Ω)

•Check the resistance V_charge line to ground (OK=10KΩ)

N100 CCONT faulty/ poor soldering

•Check if any A/D values are out of limit but the corresponding DC voltages is OK (wintesla/ local mode/ Testing/

ADC Readings…)

•If DC voltages are wrong, check corresponding voltage dividers (R100, R101)

•Check PWMOUT on R117 or R142 (1 Hz standard / 32 Hz fast)

R103 broken and N101 PSCC electrical faulty

•Check if the handset doesn't charge with the ACP-9 fast charger

•Check the mechanical appearance of the varistor R103

•If it's broken change it, in this case change also N101 PSCC

R125 and R127 connection faulty

•Check if any A/D value is out of limit special BTEMP (317≅25°)

•Check the connection between R125 and R127

•Check the NTC resistor R127 47KΩ

Autres manuels pour 3210

Table des matières

Autres manuels Nokia Téléphone portable

Nokia

Nokia 6081 Manuel utilisateur

Nokia

Nokia 7650 Manuel utilisateur

Nokia

Nokia 2115i - Mono Headset Hs-5 Hs5 2270 2285 3100 3120 3200 3205 3220... Manuel utilisateur

Nokia

Nokia 5120 - Cell Phone - AMPS Manuel utilisateur

Nokia

Nokia N81 Manuel utilisateur

Nokia

Nokia 6090 Instructions d'installation

Nokia

Nokia C20 Plus Manuel utilisateur

Nokia

Nokia 3585 Manuel utilisateur

Nokia

Nokia 6275i Manuel utilisateur

Nokia

Nokia 2320 CLASSIC RM-515 Manuel utilisateur

Nokia

Nokia N90-1 Manuel utilisateur

Nokia

Nokia 6102 Manuel utilisateur

Nokia

Nokia NEM-4 Series Instructions d'installation

Nokia

Nokia 6061 - Cell Phone 3 MB Manuel utilisateur

Nokia

Nokia N86-1 Manuel utilisateur

Nokia

Nokia N800 - Internet Tablet - OS 2007 Manuel utilisateur

Nokia

Nokia E65 Manuel utilisateur

Nokia

Nokia 2100 Manuel utilisateur

Nokia

Nokia E71 Manuel utilisateur

Nokia

Nokia 6235i Manuel utilisateur

Nokia

Nokia IP30 - Satellite Plus - Security Appliance Manuel utilisateur

Nokia

Nokia Lumia 630 Manuel utilisateur

Nokia

Nokia N97 Manuel utilisateur

Nokia

Nokia PCS VI-3155I Manuel utilisateur

Manuels Téléphone portable populaires d'autres marques

Zte

Zte BLADE A520 Manuel utilisateur

Blackbe;rry

Blackbe;rry KEYone Manuel utilisateur

Bea-fon

Bea-fon X5 Premium Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 Series Manuel utilisateur

Blackbe;rry

Blackbe;rry Storm Mode d'emploi

LG LM-X420QN Manuel utilisateur

LifeWatch

LifeWatch V Manuel utilisateur

Bea-fon

Bea-fon SILVER LINE SL860 Manuel utilisateur

IKI Mobile

IKI Mobile KF4.5i Manuel utilisateur

Hitech

Hitech HT-850 Manuel utilisateur

Yezz

Yezz Fashion F10 Manuel utilisateur

Point Mobile

Point Mobile PM60 Manuel utilisateur

Blackbe;rry

Blackbe;rry Q10 Manuel utilisateur

Blackbe;rry

Blackbe;rry Bold 9900 Manuel utilisateur

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuel utilisateur

LG LM-K420EMW Manuel utilisateur

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuel utilisateur

LG Thrive Manuel utilisateur