Nivisys DVS-110 Manuel utilisateur

QRG P/N 830-0045-0 OSR: 13-S-1241 Rev. 18 Mar 2013

DVS-110 QUICK REFERENCE GUIDE

DIVE MASK

HEAD/HELMET MOUNT ADAPTER

RELEASE LEVER

ALIGNMENT SOCKET

ALIGNMENT BOSS

CENTER PIN KNOB

ADJUSTMENT KNOB

RECEIVING DOVETAIL

MUM-14

OBJECTIVE

LENS

PURGE SCREW

(with yellow highlight)

EYECUP

EYE PIECE

MINI-RAIL

FORE/AFT ADJUSTMENT BUTTON

DVS-110 QUICK REFERENCE GUIDE

REMOVE THE EYECUP:

1. Hold the base of the eyecup tightly, aligning center line of the thumb where

the eyecup joins the eyepiece.

2. Lift eyecup away from the eyepiece while keeping a rm grip on the

eyecup.

ATTACH THE HEAD/HELMET MOUNT ADAPTER TO THE MONOCULAR:

1. Hold the monocular in the left hand with the purge screw facing up and the

objective lens away from your body. (The purge screw is located within the

mini-rail closet to the ON/OFF/IR switch.)

2. Take the head/helmet mount adapter in the right hand, holding the Center

Pin Knob between the forenger and thumb. The Alignment Boss should

be facing towards the objective lens of the monocular and can be held in

the palm of the same hand.

3. Rotate the Centering Pin Knob to raise the centering pin.

4. Slide the head/helmet mount receiving dovetail over the mini-rail of the

monocular so that the Centering Pin Knob is centered over the rail.

5. Release the Centering Pin Knob and ensure that the mount is fully locked

onto the monocular rail.

ATTACH THE MONOCULAR TO THE DIVE MASK:

1. Hold the dive mask in the right hand with the nose of the mask facing down

and the Alignment Socket towards your body.

2. Hold the monocular (with the head/helmet mount adapter attached) in the

left hand with the release lever facing up and the monocular eyepiece

facing the dive mask.

3. Press the Alignment Boss into the Alignment Socket until the release lever

catches and ensure the monocular is securely fastened to the dive mask.

INTERPUPILLARY, ELEVATION, FORE/AFT ADJUSTMENTS:

1. With the dive mask on, unscrew the Adjustment Knob until a stop occurs.

2. Firmly hold the monocular and push away from the dive mask. This

will disengage the positioning detents. CAUTION: ROTATING THE

MONOCULAR WITHOUT FULLY DISENGAGING THE POSITIONING

DETENTS WILL DAMAGE THE MOUNT ADAPTER.

3. Rotate the monocular up or down so that the eyepiece is directly in front of

the eye you intend to use in conjunction with the monocular.

4. Fore and Aft adjustments are made by pressing the fore/aft adjustment

button and moving the monocular away from and towards the mask.

5. Hand tighten the Adjustment Knob when a suitable position has be located.

Table des matières

Autres manuels Nivisys Système de vision industrielle

Nivisys

Nivisys PVS-7B/D Manuel utilisateur

Manuels Système de vision industrielle populaires d'autres marques

Festo

Festo SBOC-M-R1B-H Manuel utilisateur

Banner

Banner VE200G1B Manuel utilisateur

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manuel utilisateur

Sony

Sony Vision Exchange PEQ-C100 Manuel utilisateur

Datalogic

Datalogic MX-U81 Instructions d'installation

Cognex

Cognex In-Sight D900 Series Manuel utilisateur

Spektrum

Spektrum SPMVR2520 Manuel utilisateur

Huaray

Huaray Movidius Series Manuel utilisateur

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manuel utilisateur

SVS-Vistek

SVS-Vistek exo174 U3 Series Manuel utilisateur

Teledyne

Teledyne e2v Eliixa+ Series Manuel utilisateur

Photron

Photron FASTCAM Mini CX Series Manuel utilisateur

National Instruments

National Instruments Vision CVS-1455 Manuel utilisateur

Omron

Omron FH-L550 Manuel utilisateur

iGen

iGen NV20/20 Manuel utilisateur

JAI

JAI GO-5100MP-USB Manuel utilisateur

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manuel utilisateur

Cognex

Cognex In-Sight 9902L Manuel utilisateur