Nitroset NTS805 Series Manuel d'utilisation et d'entretien
VER 22.06
US Patent: US8397969B2
Additional Patents Pending
NTS805 Series
Operation & Safety Manual
Table of Contents
Warning and Safety Precautions
Basic Instructions
Required Safety & Protective Equipment
Misuse of the Tool
General Safety Precautions
Spall Guard Usage Instructions
Worksite Preparation
Acceptable Base Materials
Inappropriate Base Materials
Check Before Fastening
Adapter Usage Guide
Adapter Usage Table
Operating Instructions
Loading and Actuating Instructions
Using NITROSET® Tool with a NITROSET® Pole
DOs and DON’Ts
DOs
DO NOTs
Troubleshooting Guide
Replacing the Firing Pin
Tool Disassembly
Tool Assembly
Cleaning Procedure
NITROSET® Tool Full Cleaning Procedure
Interim Cleaning Procedure
Parts List & Diagram
Parts List
Parts Diagram
3
3
3
4
4
5
5
5
6-8
9, 10
10
11
12
13, 14
15
16
17
18
18
19
20
DO NOT OPERATE THE NITROSET TOOL
UNLESS YOU HAVE COMPLETELY READ
AND UNDERSTOOD THE OPERATION
AND SAFETY MANUAL
WARNING
Training is required for use of this tool.*
*Please contact your local distributor or visit www.nitroset.com for more information.
You are required to understand and follow all safety instructions for proper and
safe use of NITROSET® tools. If you require any assistance, please contact your
jobsite safety foreman or call Nitroset, LLC. at 1.800.524.4649.
Always wear proper safety equipment including safety glasses, hard hats,
hearing protection, and gloves while operating the tool.
Manipulation or modification of the tool is not permitted. Any alteration of the
tool or use of non-genuine NITROSET® parts might impair function or cause
damage to the tool. Use of non-genuine parts will void any warranties.
Do not operate in an explosive or inflammable environment.
Never put your hand over the nosepiece of the tool.
Never point the tool at yourself or any bystanders.
Never press the nosepiece against any part of your body or anyone else’s body.
Only fasten into appropriate substrates. Use of inappropriate substrates may
cause injuries.
Never attempt to disassemble, modify or alter the fastener assemblies. Use only
the required length and type of pin (with correct adapter) for the application
(Refer to the Adapter Usage Table on Page 6).
Use only genuine NITROSET® Fasteners with the NITROSET® system. Use of
incorrect fasteners may lead to injury or damage to the tool.
Required Safety & Protective Equipment
Basic Instructions*
Safety Precautions
WWW.NITROSET.COM
Misuse of the Tool
*According to ANSI A10.3 and DOT (ref: EX2009040168) NITROSET® tools are not classified as a powder
actuated tool, thus no licensing is required.
3
CAUTION
Face shield
(recommended)
CAUTION
Wear hard
hats
CAUTION
Wear hearing
protection
CAUTION
Wear safety
gloves
CAUTION
Wear safety
glasses
WWW.NITROSET.COM
Safety Precautions
Spall Guard should ALWAYS be used while operating the tool. Install appropriate spall
guard to nosepiece.
Ensure spall guard is installed flush to nosepiece.
Install the spall guard clip to the nosepiece to hold spall guard in place.
General Safety Precautions
Spall Guard Usage Instructions
4
Inspect the tool to ensure that the tool is complete, undamaged, and all parts
are secure prior to use. Damaged parts should be replaced using genuine
NITROSET® parts.
Insert the fastener assembly completely into the muzzle to ensure the correct
function of the tool. Fasteners that do not completely insert into the muzzle
should not be used and should be disposed of appropriately.
Never leave a loaded tool unattended. Only load the tool prior to fastening.
The NITROSET® tool should be reset after every actuation to clear any debris
from the nosepiece (muzzle+debris cup) of the tool.
The trigger body and reset sleeve should be held in place when loading a fastener.
Always remove fasteners and any debris from the muzzle prior to cleaning,
servicing, maintenance, or storage of the tool.
Always hold the tool securely and perpendicular to the working surface when
making a fastening.
Use the NITROSET® spall guard with clip to protect against concrete spall.
Please refer to the included Spall Guard Usage Guide.
Debris Cup Muzzle
Spall Guard
Clip Spall Guard
The NITROSET® tool is NOT for fastening into the following base materials:
Wood
Drywall
Glass
Tile
Rock
These materials may shatter causing the fastener or base substrate to fly free
and may cause serious injury to the operator or bystanders.
WWW.NITROSET.COM
Worksite Preparation
The NITROSET® tool is for fastening into the following base materials only:
Concrete
Structural Steel
Check the thickness and type of base material before fastening. Follow your
specific jobsite instructions and building code requirements.
In fastening into steel substrate, the minimum thickness of substrate must
be 3/16".
Minimum concrete thickness is three times the fastener penetration
(ie. 3" of concrete base material is a minimum requirement for 1"
penetration).
Never attempt to fasten into any material other than those listed above.
Acceptable Base Materials
Inappropriate Base Materials
Check Before Fastening
5
WWW.NITROSET.COM
Adapter Usage Guide
Note: As illustrated above, Nosepiece Gasket is inserted in the groove of the
Muzzle. Debris Cup Gasket goes between the Muzzle and Debris cup. The Red
Adapter is installed between the Muzzle and Reset Sleeve.
6
REMEMBER
To make use of the full range of the tool, always use correct adapter for
different types of pin and pin/clip assembly.
Please refer to the Adapter Usage Table on Page 7 & 8.
Muzzle Debris Cup
Gasket
Nosepiece
Gasket
Red
Adapter Debris Cup
NTS805 vs NTS805-S
Reset Sleeve of NTS805 Tool
Best used with 7/8"to 1-1/4"pin & clip Best used with 1/2"to 1"pin & clip
Reset Sleeve of NTS805-S Tool
805 805-S
The NTS805 tool comes with the standard NTS805-10 Reset Sleeve. The
NTS805-S tool comes with NTS805-10-S. Please refer to the engraved text on
the reset sleeve to verify tool model (see illustration above).
WWW.NITROSET.COM
Adapter Usage Guide 7
Adapter
Requirement
No Adapter
With Red
Adapter
STT14
CLR14-222
CLR38-222
CLR14222-BRT114
CLR14222-BRT2
CLAS525
CLSUPL525
CLRHD14-525
CLRHD38-525
CLRHD14-525-BRT114
CLRHD38-525-BRT2
CLT219
CLU222
CLC12-222
CLC34-222
CLC38-222
CLC1E-222
PIN219
PIN219T
PIN222
PIN222W
PIN222SW
PIN525
PIN532NW
Pin Pin & Clip Assembly
Fastener
Type
Adapter Usage Table (With NTS805-10 Reset Sleeve)
NTS805 Tool is assembled with the NTS805-10 Reset Sleeve. The new threadless
Muzzle can use various pin and clip assemblies with the proper Red Adapter.
805
CLAS532
CLSUPL532
WWW.NITROSET.COM
Adapter Usage Guide 8
Adapter
Requirement
No Adapter
With Red
Adapter
CLAS532
CLSUPL532
CLT219
CLR14-222
CLR38-222
CLR14222-BRT114
CLR14222-BRT2
CLAS525
CLSUPL525
CLRHD14-525
CLRHD38-525
CLRHD14-525-BRT114
CLRHD38-525-BRT2
CLU222
CLC12-222
CLC34-222
CLC38-222
CLC1E-222
PIK313
PIK316
PIN219
PIN219T
PIN222
PIN222W
PIN222SW
PIN525
PIN532NW
Pin Pin & Clip Assembly
Fastener
Type
Adapter Usage Table (With NTS805-10-S Reset Sleeve)
NTS805-S Tool is assembled with the NTS805-10-S Reset Sleeve. The new
threadless Muzzle can use various pin and clip assemblies with the proper
Red Adapter.
805-S
WWW.NITROSET.COM
Operating Instructions
1. Reset the tool before inserting the fastener to ensure the muzzle barrel is
clear of any debris.
2. Insert the fastener fully into the muzzle of the tool. Fasteners must be fully
seated in muzzle to ensure proper actuation.
(Hold reset sleeve while inserting fasteners.)
3. Place the NITROSET® tool perpendicular against the fastening surface.
A) Pull back front of muzzle until reset spring fully collapses.
B) Ensure firing pin guide clears all debris from muzzle chamber
prior to inserting new fastener assembly.
In case of jammed fasteners – Refer to the Troubleshooting Guide (Page 11) for
proper removal of all jammed fasteners.
Loading and Actuating Instructions
9
If the fastener assembly cannot be inserted into the muzzle, do not force the
fastener into the muzzle. This can jam the fastener in the tool and damage
the fastener. Fasteners that cannot be inserted should be removed and
discarded appropriately.
Fasteners should not be driven close to the edge of the base
substrate.
Always maintain a distance of at least 3" from the concrete
edge or 1" from the steel edge.
Too close to edge
Cracked concrete may actuate loudly when using the tool.
Autres manuels pour NTS805 Series
1
Table des matières
Autres manuels Nitroset Outils
