Nice EPad Manuel utilisateur

Page 1

Features:

• Stainlesssteelandcastzincalloyconstructionforresistanceagainstweatheringandvandalism.

• Eachkeyisbacklit.

• Built-intamperswitchmonitoring.

• Dooropen/closedmonitoringinput.

• Independentalarmoutput.

• Freeexitpushbuttoninput.

• Anti-hacking,multipleincorrectcodeinputlock-outandalarm.

• Eachrelayoutputcanbeindependentlysetuptolatchorpulse.

• EachrelayoutputoffersbothN/OandN/Ccontacts.

• Relay2(Auxoutput)canbeassignedtoactivate;

• SimultaneouslywithRelay1(Lockoutput).Whereeachrelaywillrespond,asperitsindependentlatchorpulsesetting.

• Whenthedoormonitoringcircuitisactivated.

• Whenthetamperswitchisactivated.

• Whenthe*keyisactivated.(Doorbell)

• Whenmultipleincorrectcodeshavebeenenteredconsecutively.

• WhenAuxcodeisentered.

• EachrelayhasitsownLEDindicatorforrelaystatusindicationataglance.

• Relay1(Lockoutput)canbeactivatedtolatchontemporarilywhileinpulsemode,usingtheunique“Bypass”code.

Specications:

Operatingvoltage: 12-24vAC/DC

Maximimumstandbycurrent: 100mA

Maximumloadondrycontactrelayoutputs: 3A@24v(Non-inductiveloadsonly)

Maximumloadonalarmoutput: 500mA@DC12v

Minimumcodelength: 4digits

Maximumcodelength: 8digits

MaximumnumberofusercodesonRelay1(Lockoutput): 98

MaximumnumberofusercodesonRelay2(Auxoutput): 1

MaximumnumberofusercodesonBypassfunction: 1

Relay1(Lockoutput)Pulselength: 1>99seconds

Relay2(Auxoutput)Pulselength: 1>999seconds

Dimensions: 120(H)x78(W)x35(D)

Ingressprotection. IP65

Stand-alone Hardwired Access Control

Keypad

Ver:EPAD_201105_008B

Nice

Page 2

1 2 34 5 6

Component Identication:

System restore (Factory default):

1. Relay1(LockOutput)terminalconnections.

2. Operatingpowerinputterminalconnections.

3. Alarmoutputterminalconnection.

4. Free-exitpushbuttoninputterminalconnection.

5. Dooropen/closedmonitoringswitchinputterminalconnection.

6. Relay2(AuxOutput)terminalconnections.

7. SystemRestore(FactoryDefault)dipswitch.

8. BypassDoormonitoring,dipswitch.

9. BypassTamperswitchmonitoring,dipswitch.

10. Built-intamperswitch.

1. Removepower.

2. Switch“Systemrestore”switchon.

3. Re-applypower.

4. Waitforbuzzertotoneconitinuously.

5. Switch“Systemrestore”switchoff.

Allsettingsandfeaturesarenowreturnedtofactorystatus.Allusercodesandthemastercodehavebeenresettofactory

default.

Page 3

Wiring:

Relay 1

Lock Output

NC COM NO

Alarm output, Free exit

push button and Door

monitoring input

ALM FRX

0v Door

Relay 2

Aux Output

COM NO

Operating

power

input

+12-24v

0v +v

Use the INI4007

diode when

power is DC. Use the INI4007 diode,

as power can only be DC.

Mag-lock example

Strike-lock example

4007

470X

Use the 47pf

capacitor when

power is AC.

LED Indications:

Power LED Green LED

Relay 1

(Lock output)

Amber LED

Relay 2

(Auxiliary output)

Red=Normaloperatingmode On=relayactive On=relayactive

Yellow=Programmingmodeactive Off=relayinactive Off=relayinactive

Flashing=Alarmactivatedsincelast

validuserentered/exited.

Enteranyvalidusercodetwicetoclear

alarmmemory.

Nice

Power LED Green LED Amber LED

Page 4

Setup a new master code: (Default = 1234)

Setting up users 1 to 19 codes for relay 1 (Lock output): (User 1 default = 3333)

Setup code to activate the relay 2 (Aux output): (Default = 9999)

Typein-CurrentMasterCode+CurrentMasterCode(chime tone)+*+00+New4to8digitMasterCode+#(chime tone)

 I.e.Tochangethemastercodeto4321:

 Typein-12341234*004321#

Typein-MasterCode+MasterCode(chime tone)+*+twodigitusernumber+NewUserCode(chime tone)

 I.e.Tosetupasingleusercode(exampleuser01to8282):-12341234*018282#

 I.e.Tosetupmultipleusercodes:-12341234*018282*022222*033333……..#

NB!WhenprogramminganewcodefortheAuxiliaryrelay,thenewcodereplacestheoldcode,withnoneedtoerase

theoldcode.

Typein-MasterCode+MasterCode(chime tone)+*+40+NewAuxiliaryCode(chime tone)+#

I.e.TosetupAuxrelaycodeto2222:-12341234*402222#

Master code:

• Themastercodeisonlyusedtoaccessprogrammingmode.(Defaultmastercode=1234)

• Themastercodecanbe4to8digitsinlength.

• Thenumberofdigitsusedforthemastercodewilldeterminethelengthofallusercodes(Lock,Auxandbypassusers)

i.e.thedefaultmastercodeis1234.Thereforeallusercodeswillbe4digitslongunlessthemastercodeischanged.

• Ifthemastercodelengthischangedafterusercodeshavealreadybeenprogrammed,thefollowingwill

occur.

• Mastercodeshortened–thelastdigitsoftheusercodewillbedroppedmakingtheusercodesthesamelengthas

themastercode.

I.e.theoldmastercodewas123456anduser01was987654.

Newmasteris1234.User01becomes9876.

• Mastercodelengthincreased–zeroswillbeaddedtotheendofallusercodessothattheusercodesareequalin

lengthtothemastercode.

I.e.oldmastercodewas1234anduser01was9876

Newmastercode=123456.User01becomes987600

• Keeparecordofallcodesandneverattempttoprogramaduplicateofanothercodealreadyinthekeypad.

I.e.user01codecannotbethesameasthemastercode.

Otherpointstonotebeforeprogramming:

• Youcannotenterprogrammingmodeifoneoftherelaysisactive.

• Youcannotenterprogrammingmodeifthetamperswitchisactive.Closeupthekeypadhousingfirstorbypassthe

tamperswitchmonitoringusingthedip-switch.

• Toexitprogramming,atanystage,pressthe#key.

Page 5

Enable the incorrect code attempt lock out (Anti-hacking) feature: (Default = Disabled)

Setup bypass code: (Default = None)

Enabale the Bypass code function: (Default = Disabled)

Deleting relay 1 (Lock output) user codes:

Setup type or pulse length of relay 1 (Lock output): (Default = 1 sec.)

Setup type or pulse length of relay 2 (Aux output): (Default = Latch mode)

Keypaddisableskeystrokesfor30sec.after5incorrectcodeentriesorif20consecutiveincorrectkeystrokeshavebeen

entered.NB!Typing#betweenkeystrokesrestartstheincorrectkeystrokecounter.

Typein-MasterCode+MasterCode(chime tone)+*+51(chime tone)+#

Repeatthistode-activateagain.

Typein-MasterCode+MasterCode(chime tone)+*+54+Newuniquebypasscode(chime tone)+#

NEVER USE WITH SOLENOID TYPE STRIKERS or LOCKS!

WhentheBypasscodeisentered,Relay1/Lockoutputlatchesonuntilthebypasscodeisre-enteredorwhentheFRX

push-buttonisused.

Enable the bypass code function:

Typein-MasterCode+MasterCode(chime tone)+*+52+1(chime tone)+#

Disable the bypass code function:

Typein-MasterCode+MasterCode(chime tone)+*+52+0(chime tone)+#

Deleting an individual user code;

Typein-MasterCode+MasterCode(chime tone)+*+50+twodigitusernumber(chime tone)+#

Deleting all user codes; (User01defaultsto3333)

Typein-MasterCode+MasterCode(chime tone)+*+50+00(chime tone)+#

Set for Latch mode;

Typein-MasterCode+MasterCode(chime tone)+*+20+00(chime tone)+#

Set for pulse mode and set pulse length;

Typein-MasterCode+MasterCode(chime tone)+*+20+01for1sec…….99for99sec(chime tone)+#

Set for Latch mode;

Typein-MasterCode+MasterCode(chime tone)+*+58+000(chime tone)+#

Set for pulse mode and set pulse length;

Typein-MasterCode+MasterCode(chime tone)+*+58+001for1sec…….999for999sec(chime tone)+#

Page 6

Advanced Programming Options and Quick Reference Table

Need Action Factory

Default

Enterprogramming Mastercode+Mastercode 1234

Master and user codes

ChangeMastercode *00+Newmastercode

Setusercodes01-19

(Relay1/Lockoutputonly)

*2digitusercode+Newuniqueusercode.

Code must be the same length as the master code. 01=3333

Setusercodes20-39and41

-98

(Relay1/Lockoutputonly)

*6+2digitusercode+Newuniqueusercode.

Code must be the same length as the master code. None

Setusercode40

(Relay2/Auxoutputonly)

*40+Newuniqueusercode.

Code must be the same length as the master code. 9999

Deleteusercodes *50+00(Forallusercodes)

*50+2digitusernumber(Forindependentusers)

01=3333ifall

deleted

Relays

setup

Setuplatchorpulselength.

(Relay1/Lockoutput)

*20+00=Latchmode

or01=1sec,02=2sec....99=99sec. 1Second

Setuplatchorpulselength.

(Relay2/Auxoutput)

*58+000=Latchmode

or001=1sec,002=2sec....999=999sec. Latchmode

Bypass

setup

Enablebypassmode *52+1 Disabled

Disablebypassmode *52+0 Default

Setbypasscode *52+Newuniquebypasscode None

Alarms and Security

Enablemultipleincorrectcode

lock-out.

(Anti-hackingfeature)

*51totogglebetweenenabledordisabled Disabled

DisableAlarmoutputmode *55+0 Disabled

Doormonitoring-forcedopenor

jammedopenalarm *55+1(Dooropentime=Relay1/Lockoutputpulselength Disabled

Tamperalarm *55+2 Disabled

Tamperanddoormonitoralarm *55+3 Disabled

Alarmactivetime *56+001for1sec,002for2sec.........999for999sec Disabled

Auxiliary Output

(Relay 2)

DisableAuxoutput *57+0 Enabled

Auxoutputtoactivatewhendoor

monitorinputistriggered(FRXfor

Auxoutput)

*57+1 Disabled

Auxoutputtoactivatewhen

anti-hackingistriggered

*57+2(NotfunctionalifRelay2/Auxoutputissettolatch

mode) Disabled

Auxoutputtoactivatewhen*key

ispressed.(Doorbellfunction) *57+3 Disabled

Auxoutputtoactivatewhentam-

peristriggered *57+4 Disabled

Auxoutputtoactivatewhendoor

isforcedorjammedopen *57+5 Disabled

AuxoutputtoactivatewhenRe-

lay1/Lockoutputisactivated *57+6 Disabled

Auxoutputtoactivatewhenuser

40codeisentered *57+7 Enabled

Page 7

Using the Keypad

Normal operation:

Alarm Monitoring Function:

Bypass Function:

ToactivateRelay1/Lockoutput,simplytypeinavalidcodeforthatrelayorpressandreleasethefreeexitpushbuttonifone

hasbeeninstalled:

 -Therelaywillactivateinthemannersetupbytheinstaller.

 -ThegreenLEDindicatorwillactivateaspertherelay.

ToactivateRelay2/Auxoutput,simplytypeinthevalidcodeforthatrelayorpressandreleasethefreeexitpushbuttonifthis

functionhasbeenconfiguredandinstalled:

 -Therelaywillactivateinthemannersetupbytheinstaller.

 -TheyellowLEDwillactivateaspertherelay.

Ifthealarmmonitoringhasbeensetupbytheinstaller,andanalarmconditionoccurs,thefollowingwillhappen;

• Alarmoutputactivates,

• Builtinbuzzersounds,

• GreenLEDbeginsflashing.

Thefollowalarmconditionsareavailable:

• Dooropenedwithoutavalidcodeentryfirst.(Doorforcedalarm)

• DoornotclosedbythetimetheRelay1/Lockoutputreturnstostandbystatus.(Doorjammedopenalarm)

• Keypadhousingopened.(Tamperalarm)

Afterthealarmtime(setbytheinstaller)hasexpired,thealarmoutputandthebuiltinbuzzerresets.However,the

flashinggreenLEDcontinuesuntilthefirstvalidusercodeisenteredintothekeypad.Thiswaytheuserismadeaware

thatanalarmconditionoccurredevenafterthebuiltinbuzzerandalarmoutputhavereset.

TO AVOID OVERHEATING OF THE SOLENOID, NEVER USE THIS FUNCTION WITH ELECTRO-MECHANICAL

STRIKERS or LOCKS!

Incasessuchasanofficeparkorschoolgateautomation,thatneedstotemporarilybekeptopentoallowforpeaktraffic

periods,thisfunctioncanbeused.

Thisfunctionrequiresadedicatedcodewhichissetupbythemastercodeholder.

Whenthebypasscodeisentered,Relay1/Lockoutputwilllatchonuntileitherthesamecodeisenteredagainorthefree

exitpushbuttonispressed.

Whilethebypassfunctionisactive,nootherRelay1/Lockoutputusercodewillreleasetherelay.

Thisfunctionisalsousefulwhereamagneticlockisinstalled.

Page 8

Tel: +27 21 404 0800 Tech support email: supportza@niceforyou.com Webpage: www.niceforyou.com/za

WARRANTY:

1. AllgoodsmanufacturedbyNiceGroupSA(Pty)Ltdcarrya12monthfactorywarrantyfromdateofinvoice.

2. Allgoodsarewarrantedtobefreeoffaultycomponentsandmanufacturingdefects.

3. Faultygoodswillberepairedorreplaced,atthesolediscretionofNiceGroupSA(Pty)Ltd,freeofcharge.

4. ThiswarrantyissubjecttothegoodsbeingreturnedtothepremisesofNiceGroupSA(Pty)Ltd.

5. Thecarriageofgoodsisforthecustomer’saccount.

6. Thiswarrantyisonlyvalidifthecorrectinstallationandapplicationofgoods,aslaidoutintheapplicabledocumentation

accompanyingsaidgoods,isadheredto.

7. Allwarrantyclaimsmustbeaccompaniedbytheoriginalinvoice.

8. Allclaimsmadebytheendusermustbedirectedtotheirrespectiveserviceprovider/installer.

Thefollowingconditionswilldisqualifythisproductfromthewarrantyaslaidoutabove.Theseconditionsarenon-negotiable.

1. Anyunauthorizednon-manufacturermodificationstotheproductorcomponentsthereof.

2. Anymodificationtotheinstallationmethodsdescribedintheinstallationinstructions.

3. Any application or use of the product other than the intended use and application prescribed in the product

documentation.

Thefollowingitemsarenotincludedinthewarrantyortheycarryaspecialwarrantyconditionoftheirown.

1. Damageresultantofwindandotherclimaticinfluencessuchaslightningstrikes.

2. Damageduetohighvoltagesurges.

3. Damageduetoinfestationi.e.Antsnesting…

4. Waterdamage.Itistheresponsibilityoftheinstallertoensuretheproductisinstalledinalocationthatisprotected

fromwateringress.Theingressprotectionratingisspecifiedintheaccompanyingdocumentation.Housingsthat

requirethatcableentriesbe madebythe installerdonot carryanex-factory ingressprotectionrating asitis the

responsibilityoftheinstallertosealthecableentrypointsafterinstallationofthecabling.

Table des matières

Autres manuels Nice Contrôleurs d'accès IP

Nice

Nice C2 PRO Caractéristiques techniques

Manuels Contrôleurs d'accès IP populaires d'autres marques

ZKTeco

ZKTeco SpeedFace-V5L Manuel utilisateur

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

ZKTeco

ZKTeco OP-200 Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur