NexSens X2-CB-C Manuel utilisateur

X2-CB-C Quick Start

For best results, setup your new system in the office/lab. Collect a few data

points and become familiar with the system prior to field deployment.

1Go to V2.WQDataLIVE.com/Getting-Started

2Create a new account or sign

into an existing account and

enter the Claim Code found

on the serial label to access

the device’s data

3Place the X2-CB in an area

with strong cellular coverage

4Remove the required blank

sensor plugs (P0/P1/P2)

5Connect all sensors

6Remove the COM/SOLAR blank plug

7Connect the 6-pin solar panel plug to

power the X2-CB

(device will beep once when powered)

8Wait up to 60 seconds for the system

to check cellular coverage

Two beeps = good signal

Three beeps = no signal

(See troubleshooting)

9Wait (typically 5-10 minutes1) for

sensor detection, sensor reading, and

data upload to complete

Device will beep twice when data upload begins

Device will beep constantly for 3 seconds when done

10 Refresh WQData LIVE and confirm all sensor parameters are shown

and valid sensor readings appear

For more information on the X2-CB, visit our online knowledge base

www.NexSens.com/Knowledge-Base/X2-Data-Logger/Getting-Started-X2-CB.htm

1A brand new modem may require an additional 2 minutes to provision

with the cellular provider the first time it connects to the internet.

Serial Label

Troubleshooting

Symptom

Possible Cause

Corrective Action

Claim code

does not work

Code entered

incorrectly

Re-enter code exactly as shown on the

serial label

Device already

claimed

Check with previous owners/users

WQData LIVE’s

Last Contact

time does not

update

Device does

not upload

new data to

WQData LIVE

No power to

device

Ensure there is either a solar panel or

UW-JUMPER plugged into the

COM/SOLAR UW-6 port

Confirm voltage between pins

3 (+) and 4 (-) on the

COM/SOLAR port is 12-14VDC

No cellular

coverage

Relocate the unit to an area with strong

cellular coverage and no obstructions

(outside in a parking lot is typically good),

then cycle the power (remove and

reconnect UW-6 COM/SOLAR plug). The

device should beep twice after being

powered for 30-60 seconds. Three beeps

indicates no signal.

Sensor or

parameter

does not

appear on

WQData LIVE

Sensor not

connected

Confirm the UW-8 plug is screwed down

securely

Sensor

damaged

Visually inspect the sensor & cable, then

check direct communication with PC or

other configuration device

Sensor not

configured

Ensure multiple sensors do not share the

same SDI-12 or MODBUS address and

that sensor is setup correctly

Sensor not

supported

Confirm the sensor is compatible with

the X2-CB

For more assistance visit:

www.NexSens.com/Category/Knowledge-Base/X2-Data-Logger

Autres manuels NexSens Enregistreur de données

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens X2-CBMC-C Manuel utilisateur

NexSens

NexSens X2-SDLMC Manuel utilisateur

NexSens

NexSens X2-Cell Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens SDL500 Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens X2-SDL Manuel utilisateur

NexSens

NexSens CB-50 Data Buoy Manuel utilisateur

NexSens

NexSens X2-SDL Manuel utilisateur

NexSens

NexSens X2-CB Manuel utilisateur

NexSens

NexSens 3100-iSIC Manuel utilisateur

NexSens

NexSens CB-150 Data Buoy Manuel utilisateur

NexSens

NexSens CB-1250 Data Buoy Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

NexSens

NexSens CB-1250 Data Buoy Manuel utilisateur

NexSens

NexSens X2 Manuel utilisateur

Manuels Enregistreur de données populaires d'autres marques

TESTO

TESTO 176 Manuel utilisateur

HT Italia

HT Italia XL421 Manuel utilisateur

HBM

HBM SOMAT XR CX22B-R Manuel utilisateur

Agtrix

Agtrix 380i Manuel utilisateur

Hobo

Hobo H8 Pro Manuel utilisateur

Beijing ART Tech

Beijing ART Tech PCI2320 Manuel utilisateur

Athena

Athena GET SL1 Manuel utilisateur

Motec Systems

Motec Systems C185 Manuel utilisateur

Beijing ART Tech

Beijing ART Tech USB2832 Manuel utilisateur

Rotronic

Rotronic HygroLog HL20 Manuel utilisateur

MRC

MRC DW-6092 Manuel utilisateur

Racelogic

Racelogic VBOX LapTimer Manuel utilisateur

Edu-Logger

Edu-Logger 900-240 Manuel utilisateur

Elma

Elma DT173 Manuel utilisateur

MadgeTech

MadgeTech PRTemp140 Fiche technique

Comet

Comet U0121M Manuel utilisateur

pico Technology

pico Technology PT-104 Manuel utilisateur

Soil Instruments

Soil Instruments GTecLink Manuel utilisateur