NeuraLabel Sirius Manuel utilisateur

Page

NeuraLabel Sirius Printer

Installaon and Quick Start Guide

Download Complete Guides at:

www.neuralabel.com/neuralabel‐sirius‐label‐printer‐support

www.neuralabel.com May 2020

Page 3

The packing box and packing materials are needed to transport the

machine. Keep them and do not throw them away

In the Boxes

 Printer

 Unwinder

 Power Cable

 Preinstalled in Printer

 Toner: Cyan, Magenta,

Yellow, Black, White*

 Transfer Belt

 Fuser

Things to Prepare (Not Included)

 LAN Cable (for network connecon)

 USB Cable for Printer to Computer connecon

* Included with Sirius5 only.

This printer supports the operang systems (OS) listed below:

Windows 10/Windows 10 (64‐bit version); Windows 8.1/Windows 8.1 (64‐bit version);

Windows 8/Windows 8 (64‐bit version); Windows Server 2016; Windows Server 2012

R2; Windows Server 2012; Windows 7/Windows 7 (64‐bit version); Windows Server

2008 R2; Windows Server 2008/Windows Server 2008 (x64 version)

*With Windows 10, Windows 8.1 and Windows 8, only the desktop mode is supported.

Page 4

Installaon Space

When selecng an installaon locaon, ﬁnd one that meets the following

speciﬁcaons:

 locaon that is level and can support the weight of the machine

(approximately 140 lbs).

 locaon near a power socket that can easily accessed.

 locaon that meets the equipment installaon space guidelines

shown in the diagram.

Page 5

Unpacking Printer

1. Open the top of the box and re‐

move the accessories.

2. Remove top layer of packing

materials.

3. Remove the handles (4 pieces),

and then remove the top of the

packing box.

Page 6

4. Open out the boom part of the

box, place your hands on the

printers handles and support the

printer as you remove the front

and back packing materials on

the boom.

5. Cut and remove the bands that

secure the printer.

6. Remove the plasc bag.

7. Place the printer in the idenﬁed

installaon space.

Page 7

8. Remove the desiccant.

9. Grasp the top cover open lever

and open the top cover.

10. Remove the holding tape from the edges

of the top cover (4 pieces).

11. Remove the Pad‐TC from the top

of the print cartridge, and re‐

move the tape securing the liup

lever.

12. Turn the liup lever to lower the

print cartridges.

Page 8

13. Pull out the sheet‐protecon.

14. Close the top cover.

Page 9

4. Remove the plasc bag from the

unwinder, and then remove the ac‐

cessories.

5. Peel oﬀthe tape from two loca‐

ons.

Unpacking Unwinder

1. Open the top of the packing box.

2. Remove the top layer of packing

materials.

3. Remove the unwinder.

Page 10

Installing the Unwinder to the Printer

1. Check whether the adjuster on the

unwinder is raised up. If the ad‐

juster is not raised, before you

mount it on the printer, rotate it to

2. Hold the unwinder close to the

mounng pins and mounng

hole, and then press it against the

right side of the printer and lower

it.

3. Use three screws to secure the

unwinder to the printer. Tighten

the screws in order (1, 2, 3) as

show in the diagram.

4. Extend the adjuster so it contacts

the table and raises the unwinder

core oﬀthe table.

Page 11

Printer Setup

Connecng to a PC

Network Connecon

Manual IP

Network Connecon ‐

Automac IP USB Connecon

Install the printer driver.

Connect the cable.

Turn on the printer.

Set the printer's IP

address

Connect the cable.

Turn on the computer.

On the computer, add the

printer using the

manually assigned IP

address.

On the computer, add the

printer using the auto‐

assigned IP address from

the User Panel.

Ensure printer is installed

on Control Panel.

Table des matières

Autres manuels NeuraLabel Étiqueteuse

NeuraLabel

NeuraLabel 550e Manuel utilisateur

NeuraLabel

NeuraLabel 500e Manuel utilisateur

NeuraLabel

NeuraLabel Sprint Manuel utilisateur

NeuraLabel

NeuraLabel 300x NoTouch Manuel utilisateur

NeuraLabel

NeuraLabel 600e Guide de configuration

NeuraLabel

NeuraLabel 550e Manuel utilisateur

NeuraLabel

NeuraLabel Sirius 4 Manuel utilisateur

NeuraLabel

NeuraLabel Sprint Manuel utilisateur

NeuraLabel

NeuraLabel 550e Manuel de l'opérateur

NeuraLabel

NeuraLabel 600e Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur