Netum E800 Manuel utilisateur

Package Included:

1 x Scanner;

1 x USB Cable;

1 x USB Dongle;

1 x Retractable Clip;

1 x Clip; 1 x Quick Setup Guide;

For a complete user guide:

https://www.netum.net/pages/barcode-scanner-user-manuals

(1)

NT033

(2)

Product Description

Scan button

Scanning Window

Battery Light/Read

Indicator Light

(Green/Blue/Red)

Scan Button

Lanyard Eyelet

Power On Button/

Scan button

USB Type C

peel off the �ilm from back of the

clip and stick it to the back of your

remote device

(3)

Back Clip

(4)

Charge the scanner

Warning Tone· Red Light - Charging

· Green Light - Fully charged

· Improtant Notes: DC PlugV: 5V; A>500mA

Connect Scanner with your host through USB cable (provided by Netum) or

take a DC plug and charge it on an electrical wall outlet.

Low battery warning - 2 beeps, LED in red �lashing twice

Running out of battery - 5 beeps, LED in red �lashing 5 times

Scanning will not read any barcodes when it’s running out of battery.

Get Battery Volume

By scanning below command barcode will get rough battery volume.

Firmware Version

Firmware version will be displayed by scanning “$SW#VER”.

%BAT_VOL#

$SW#VER

Factory Defaults

Scanning the following barcode will restore the scanner to the factory. Scanner will power off after you scanning Factory Restore.

Barcode Programming

Netum barcode scanners are factory programmed for the most common

terminal and communication settings. If you need to change these settings,

programming is accomplished by scanning the bar codes in this guide. An

asterisk (*) next to an option indicates the default setting.

Important Notes :

Many command barcodes only work in a particular transmission mode. Please

pay attention to below symbol when you scanning the command barcodes.

Command barcodes only apply to transmit characters through Bluetooth .

Command bacodes only apply to transmit characters through USB Dongle .

Command bacodes only apply to transmit characters through USB cable .

Connect scanner to a host device

Characters can be transferred from scanner to your device through USB cable,

USB Dongle or Bluetooth, choose one of the connection ways to get started:

USB Wired Connection

1)Connect scanner with your computer via type-C cable.

2) Setup keyboard language. For example if you use French keyboard, just scan

“French keyboard” from keyboard language setcion in page 9.

3) Locate cursor on the place where you want scanner to output the characters

then you can start to scan.

Factory Restore

(5)

%#IFSN0$B

(6)

%#IFSNO$4

Bluetooth Transmit

USB Wireless Connection

1) Plug USB dongle into your computer.

2) Setup keyboard language. For example if you use French keyboard, just

scan “French keyboard” from keyboard language setcion in page 9.

3) Locate cursor on the place where you want scanner to output the

characters

then you can start to scan.

Bluetooth Connection

1) By scanning “Bluetooth Transmit”, scanner powers off immediately. Press

power on button. Blue LED will start to �lash.

2) Turn host device’s Bluetooth on and �ind “E barcode scanner” from your

bluetooth list, tap it and pair.

3) Locate cursor on the place where you want scanner to output characters

then you can start to scan.

Important Notes:

• Make sure the device is in range with Bluetooth turned on.

• If a connection is made, the blue light will stop blinking and turn solid.

• If a connection is not made after several attempts, the scanner will emit a

long beep (and the blue light will turn off).

%#IFSN0$1

*Wireless Transmit

(7)

Basic Mode (HID) *

• NO software installation needed

• Connects to most devices

• Scanner interacts with host device like a keyboard

Important Notes:

If you want to shift from HID to SPP or BLE just scan the Corresponding

command barcode. If you want to shift from SPP or BLE to HID mode, ignore

(or delete) "E Barcode Scanner"→ turn off bluetooth→ scan Basic Mode

(HID)→ Open the bluetooth → re-pair it.

Applicatin Mode (Apple Speci�ic Serial Pro�ile)

• For iOS Devices

• If you have an iOS application that supports our Scanners this is the

mode to use.

Application Mode (Serial Port Pro�ile)

• For Android or Windows

• Software installation is required.

• If you have an application that supports this is the mode recommended.

AT+MODE=2

AT+MODE=3

AT+MODE=1

Transmission Speed Via Bluetooth Connection

By scanning the appropriate barcode will change bluetooth transmit speed.

(8)

POP OUT IOS Keyboard

IOS Keyboard will be disabled when pairing scanner to IOS device.

By pressing scanning button in the middle for 4 seconds then release it, will pop

out the IOS keyboard.

AT+HIDDLY=4

High Speed

AT+HIDDLY=10

*Medium Speed

AT+HIDDLY=25

Low Speed

Enable/*Disable

(9)

Scan Mode:

Continue Scan Mode

This mode enables the scanner to scan/capture, decode and transmit over

and over again. By clicking scan button in the middle will turn off/on the

continuous scan Mode.

continuous Scan Mode

Trigger Mode

Scanning this bar code will enable the scanner to enter manual trigger

mode.

*Trigger Mode(Default)

(10)

$LAN#EN

*America EN keyboard

$LAN#FR

French keyboard

$LAN#GE

Germany keyboard

$LAN#IT

Italy keyboard

$LAN#PT

Portugal keyboard

$LAN#ES

Spain keyboard

$LAN#UK

UK keyboard

$LAN#HU

Hungary keyboard

For example If you use French Keyboard, scan command barcode of “French

keyboard ”. US keyboard was setup by default.

Keyboard Language

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Netum Lecteur de codes-barres

Netum

Netum NT-W5 Manuel utilisateur

Netum

Netum NT-1200 Manuel utilisateur

Netum

Netum C Series Manuel utilisateur

Netum

Netum NT-1203 Manuel utilisateur

Netum

Netum RS-8000 Manuel utilisateur

Netum

Netum NT033 Manuel utilisateur

Netum

Netum NT-1228BL Manuel utilisateur

Netum

Netum NT-W6 Manuel utilisateur

Netum

Netum NT-1698W Manuel utilisateur

Netum

Netum C Series Manuel utilisateur

Netum

Netum NT-1228BL Manuel utilisateur

Netum

Netum NT-9600 Manuel utilisateur

Netum

Netum NT-W8 Manuel utilisateur

Netum

Netum NT-1228BC Manuel utilisateur

Netum

Netum NT-M3 Manuel utilisateur

Netum

Netum NT-1203 Mode d’emploi

Netum

Netum M1 Manuel utilisateur

Netum

Netum NT-W3 Manuel utilisateur

Netum

Netum DataMatrix pdf417 Manuel utilisateur

Netum

Netum NT-1228BL Manuel utilisateur

Netum

Netum W3 Manuel utilisateur

Netum

Netum NT-M7 Manuel utilisateur

Netum

Netum C200 Manuel utilisateur

Netum

Netum NT-1202 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur