Netstor NA341TB3 Manuel utilisateur

Second edition, Mar. 2019

User Manual

NA341TB3

Rackmount 2U 8 bay (3.5"/ 2.5") Thunderbolt™ 3 RAID Storage

1. Unpack the NA341TB3

2. Storage Enclosure Description

5. Verification 10

6. Thunderbolt 3 Card LEDs Status 17

4. Power On/Off NA341TB3 9

2.1 Panel Layout

2.2 Environmental Control Board LED Status

3. Setup Procedure 6

3.1 Storage Setup

3.2 Blower Fan Speed Adjustment

5.1 macOS

5.2 Windows Operating System

3Go Top ↑

1. Unpack the NA341TB3

2. Storage Enclosure Description

2.1 Panel Layout

The box contains the following items:

。Netstor NA341TB3 storage

。HDD tray × 8 (installed in enclosure)

。Thunderbolt 3 cable (2 meters) × 1

。Power cord × 1

。HDD mounting screws

。Key for HDD tray × 2

1. HDD Power LED

。White - Power On Indicator

4. Fan LED

。Green – normal

。Red – fan failure (low frequency of RPM or stop)

5. Temperature LED

。Green – normal

。Red – over temperature

3. Mute Button

。Mute Buzzer Beeping

2. HDD Status LED

。Flash Blue - HDD Accessing Indicator

。Red - HDD Failure Indicator

4Go Top ↑

8. Hot-Swappable Blower Fan 1

。75 × 75 × 28 mm

9. Hot-Swappable Blower Fan 2

。75 × 75 × 28 mm

10. Inner Cooling Fan 3

。60 × 60 × 25 mm

11. Inner Cooling Fan 4

。60 × 60 × 25 mm

12. Thunderbolt 3 Connectors

。Connecting Thunderbolt 3 cables to host

and downstream device

6. Power Cord Receptacle

7. PSU Power Switch

13. Thumbscrews to loosen/

tighten the top cover

5Go Top ↑

2.2 Environmental Control Board LED Status

D2 LED: fan failure indicator

。D2 LED no light: all cooling fans are normal

。D2 LED red light: one of the fans fails

D4 LED: fan 1 status

。D4 LED no light: fan 1 is normal

。D4 LED red light: fan 1 fails

D5 LED: fan 2 status

。D5 LED no light: fan 2 is normal

。D5 LED red light: fan 2 fails

D6 LED: fan 3 status

。D6 LED no light: fan 3 is normal

。D6 LED red light: fan 3 fails

D7 LED: fan 4 status

。D7 LED no light: fan 4 is normal

。D7 LED red light: fan 4 fails

6Go Top ↑

3. Setup Procedure

3.1 Storage Setup

1. Place NA341TB3 storage on a level surface on a stable table.

2. Take out all the eight HDD trays.

7Go Top ↑

3. Place HDDs in the trays and ﬁx them with the included hard drive mounting

screws. And then put the trays with HDDs back to NA341TB3 storage.

4. Connect NA341TB3 and Thunderbolt 3 computer with Thunderbolt cable,

and then connect Netstor storage with power source.

Host

Power

8Go Top ↑

3.2 Blower Fan Speed Adjustment

1. There are two hot-swappable 75×75×28 mm blower fans for ventilation at rear of NA341TB3.

After loosening the two thumbscrews on the fan module, the blower fan can be pulled out of

the storage enclosure.

2. The rear 75×75×28 mm blower fan speed can be adjusted. As the blower fan module is

pulled out, there are four sets of jumpers labeled with 6V, 8V, 10V, 12V from top to

bottom on the fan connector board. The default setting is the jumper being placed over

pin 7 and 8 for label 6V for slowest speed. The speed increases from label 8V to label 12V.

As jumper is not placed over pins, the fan will spin at 12V full speed.

10V

12V

9Go Top ↑

4. Power On/Off NA341TB3

1. NA341TB3 storage is designed to be powered on/off simultaneously with

the Thunderbolt 3 computer as NA341TB3 is connected to computer by

Thunderbolt cable. Therefore, power on computer ﬁrst, and then NA341TB3

will be powered on automatically.

2. As NA341TB3 storage is connected to computer by Thunderbolt cable, when

shutting down computer, the NA341TB3 will be shut down automatically as well.

※ NA341TB3 supports hot-plug and hot-unplug for powering on and off.

※ If there is a PSU power switch on Netstor storage, remember to switch it

to “I” position to enable the PSU ﬁrst.

10 Go Top ↑

5. Verification

5.1 macOS

1. Verify Netstor NA341TB3 is recognized by computer. Click Apple icon at the top

menu bar, select About This Mac, and click System Report button. Click Thunderbolt

in the left column, as NA341TB3 appears in the information, it means Netstor storage

is recognized correctly by computer.

2. Verify RAID controller of NA341TB3. Right after the above point 1, click PCI in the left column,

and information about NA341TB3 RAID controller will appear. (For RAID controller, from starting

up, it will take more time for its info to be shown)

Table des matières

Autres manuels Netstor Enceinte

Netstor

Netstor NA333A-G3 Manuel utilisateur

Netstor

Netstor HercuLes HL23T-PRO Manuel utilisateur

Netstor

Netstor TurboBox Pro NA250A Manuel utilisateur

Netstor

Netstor NA211TB Manuel utilisateur

Netstor

Netstor 6Gb/s SAS JBOD Manuel utilisateur

Netstor

Netstor TurboBox Rac NA260A Manuel utilisateur

Netstor

Netstor NS780TB3 Manuel utilisateur

Netstor

Netstor NS385S-8028 Manuel utilisateur

Netstor

Netstor TurboBox Xtreme NA265A Manuel utilisateur

Netstor

Netstor NA341A Manuel utilisateur

Netstor

Netstor NS780S-G3 Manuel utilisateur

Netstor

Netstor NS722TB3 Manuel utilisateur

Netstor

Netstor NS372TB3 Manuel utilisateur

Netstor

Netstor TurboBox Xtreme Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur