NETGEAR ProSafe GS516TP Manuel utilisateur
Installation Guide
NETGEAR Smart Switch™ GS516TP
Package Contents
•NETGEAR Smart Switch™ GS516TP
•Rubber footpads for tabletop installation
•AC power cord
•Rack-mount kit for rack installation
•Installation guide
•Smart Switch resource CD that includes the Smart Control Center Utility and
GS516TP Hardware Installation Guide. (A link to the online GS516TP Software
Administration Manual is on the resource CD.)
Configure the Switch
Install the Smart Control Center Utility and use it to configure the switch.
Install the Smart Control Center Utility on a Computer
1. Insert the resource CD into your CD drive.
2. Run the Setup program to install the Smart Control Center Utility.
The Installation Wizard guides you through the installation.
Connect Your Smart Switch
If you have a DHCP server in your network, see Connect the Switch to Your
Network.
If you are using static IP addresses in your network, first see Configure the Switch
with a Static IP Address, and then see Connect the Switch to Your Network.
Configure the Switch with a Static IP Address
If you are using a static IP address in your network, configure the switch IP address
before connecting the switch to your network. The default IP address of the switch is
192.168.0.239.
Note: If you are using a DHCP server in your network, this procedure does not apply
to you; instead, go directly to Connect the Switch to Your Network.
1. Set up the computer with a static IP address in the 192.168.0.x subnet.
2. Connect the computer to the switch.
3. Configure the IP address of the switch to match your network configuration.
Connect the Switch to Your Network
1. Connect each computer to an RJ-45 network port on the switch front panel.
Use Category 5 (Cat 5) or better Ethernet cable terminated with an RJ-45
connector to make these connections.
2. Connect the switch to your network.
3. Power on the switch by connecting the AC power cord to an outlet, or by
connecting an Ethernet cable from PD ports 15 or 16 (or both) to a PSE
device.
4. Verify that the computer with the Smart Control Center Utility is on the same
subnet as the switch.
Internet
Configure the Switch with the Smart Control Center
Utility
1. Double-click the Smart Control Center Utility icon on your desktop or
click the icon in the Windows Start menu to run the utility and view this screen.
2. Click the Discover button.
The Smart Control Center Utility finds the switch and displays its MAC address,
IP address, and model number.
May 2013
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to
change without notice. © NETGEAR, Inc. All rights reserved.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
If the utility does not discover your switch, verify that the cable connections are
secure and that the IP address configuration of the computer is in the same
subnet as the switch, and click the Discover button.
3. Click the row for the switch that you want to configure.
4. Click the Web Browser Access button to view the switch Login screen.
5. Enter the default password of password in lower-case letters and click the
Login button.
The System Information screen displays.
6. Configure the switch for your network.
For more information, see the GS516TP Software Administration Manual.
Troubleshooting Tips
Here are some tips for correcting simple problems you might have.
•Be sure to power on your computer and switch in the following sequence:
1. Turn on the switch and wait about two minutes.
2. Turn on the computer and connect to the switch.
•Make sure the Ethernet cables are plugged in.
For each powered-on computer connected to the switch, the corresponding
switch LAN port status LED is lit.
•Make sure the network settings of the computer are correct.
In most cases, computers should be configured to obtain an IP address through
DHCP.
If your network uses static IP addresses, be sure that the switch and computer
are configured with valid IP addresses. For more information, see the software
administration manual.
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and
use it to register your product at https://my.netgear.com.
You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support
resources.
For additional information about setting up, configuring, and using your smart
switch, see the software administration manual.You can get the manual online at
http://downloadcenter.netgear.com.
Autres manuels pour ProSafe GS516TP
1
Autres manuels NETGEAR Changer
NETGEAR
NETGEAR DS104 Manuel utilisateur
NETGEAR
NETGEAR GS605 - Gigabit Desktop Switch Manuel utilisateur
NETGEAR
NETGEAR ProSafe GS108 Manuel utilisateur
NETGEAR
NETGEAR GSS108E Manuel
NETGEAR
NETGEAR ProSafe GS108 Manuel utilisateur
NETGEAR
NETGEAR ProSafe Plus Manuel utilisateur
NETGEAR
NETGEAR FS116P - ProSafe 16 Port 10/100 Desktop... Manuel utilisateur
NETGEAR
NETGEAR FS726TP - ProSafe Smart Switch Manuel utilisateur
NETGEAR
NETGEAR ProSafe GS700TP Manuel utilisateur
NETGEAR
NETGEAR GS716T - ProSafe Switch Manuel utilisateur
NETGEAR
NETGEAR GSM7248R - ProSafe Switch Manuel utilisateur
NETGEAR
NETGEAR GSM7352SNA - Prosafe 48 Port Gigabit L3 Managed Stackable... Manuel utilisateur
NETGEAR
NETGEAR SB104 Network Starter Kit SB104 SB104 Manuel utilisateur
NETGEAR
NETGEAR ProSafe JGSM7224 Manuel
NETGEAR
NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart... Manuel utilisateur
NETGEAR
NETGEAR GS110 Manuel utilisateur
NETGEAR
NETGEAR WFS709TP - ProSafe Smart Wireless Controller Manuel
NETGEAR
NETGEAR FS516 - Switch Manuel utilisateur
NETGEAR
NETGEAR GS305P Manuel utilisateur
NETGEAR
NETGEAR GS110EMX Manuel utilisateur
