NETGEAR FSM7328S - ProSafe Switch Manuel utilisateur

7000 Series (Firmware 6.0.0.15)

Configuring VLANs and Routing

Scenario:

Creation of a 2 VLAN Routed network with access to the Internet via

an FVS Router/Firewall.

VLAN 3 being the Users PC domain

VLAN 2 being the Internet domain

Network Diagram:

Physical Setup:

1x FSM7328S Prosafe Layer 3 Managed switch - Firmware 6.0.0.15

4x Windows XP Computers (2x on each VLAN)

1 x FVS___ Prosafe Firewall Router

Logical Setup:

FVS___ : 192.10.10.1/24

VLAN 2 –192.10.10.0/24

VLAN 3 –172.10.11.0/24

VLAN2 IP address 192.10.10.254

VLAN3 IP address 192.10.11.254

WORKING INSTRUCTIONS

Set the Management IP address

1) Plugged the console cable to the Serial port of the switch and the serial port on the

PC

2) Open a new Hyper Terminal session (connecting via the COM port) –settings 9600,

8 , None , 1, None

3) Power Cycle the switch

4) Upon POST the User: prompt will appear

5) Username is admin , password “blank”

6) Type Enable to access the privileged mode (password “blank” )

7) Type network protocol none to reset the network settings

8) Type network parms <<Management IP>> <<Subnet Mask>> <<Default Gateway

IP>>. For example network parms 192.168.0.1 255.255.255.0 192.168.0.1

9) User copy system:running-config nvram:startup-config to save the configuration

10) Check with show network if the settings are correct

The switch should now be accessible patching a CAT5 Straight-through cable. The PC

NIC must be configured with an IP address within the same subnet used to configure the

management IP of the switch (Example: 192.168.0.2 255.255.255.0

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The UNIT/SLOT/PORT entry will show the Virtual PORT created

and associated to the new VLAN.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

WEB GUI instructions

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The following statement should be prompted.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

8) The following summary should be obtained:

Checking routing is in place on the switch

1) Browse to Routing –RIP –Interface Summary

2) The following situation should appear

NOTE: The RIP admin mode will show ENABLE only if at least one active device is

patched into a port in the relevant VLAN

NOTA BENE:

Router/Firewall:

If the firewall as in this case is patched into a port in a specific VLAN (VLAN2 here),

ensure its static routing table contains a route back to the VLAN IP address for each of

the other VLANS on the switch that require Internet access.

For example in this case the FVS Firewall must contain the following route:

192.10.11.0 (Subnet) 255.255.255.0 (Subnet Mask) 192.10.10.254 (Default Gateway).

On the other hand another option would be to run RIP on the Firewall.

Autres manuels pour FSM7328S - ProSafe Switch

7

Table des matières

Autres manuels NETGEAR Changer

NETGEAR

NETGEAR AV Series Manuel

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR FS509T Manuel utilisateur

NETGEAR

NETGEAR GS108Tv3 Manuel utilisateur

NETGEAR

NETGEAR 200 Series Manuel utilisateur

NETGEAR

NETGEAR GS110EMX Manuel utilisateur

NETGEAR

NETGEAR ProSafe GS116 Manuel utilisateur

NETGEAR

NETGEAR ProSafe GSM7228PS Manuel utilisateur

NETGEAR

NETGEAR GSM7328Sv2 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable... Manuel utilisateur

NETGEAR

NETGEAR ProSAFE S3300-52X Manuel utilisateur

NETGEAR

NETGEAR FSM7326P - ProSafe Managed Switch Manuel

NETGEAR

NETGEAR GSM7352SNA - Prosafe 48 Port Gigabit L3 Managed Stackable... Manuel utilisateur

NETGEAR

NETGEAR DS108 - Hub Manuel utilisateur

NETGEAR

NETGEAR GS110TUP Manuel

NETGEAR

NETGEAR ProSafe JGS524v2 Manuel de la liste des pièces

NETGEAR

NETGEAR S350 Series Manuel utilisateur

NETGEAR

NETGEAR ProSafe GS105 Manuel utilisateur

NETGEAR

NETGEAR ProSafe GS700TP Mode d’emploi

NETGEAR

NETGEAR GS608v3 Manuel utilisateur

NETGEAR

NETGEAR ProSafe FS752TP Manuel utilisateur

NETGEAR

NETGEAR ProSAFE JGS524Ev2 Manuel utilisateur

NETGEAR

NETGEAR GSM7212 - ProSafe Switch Manuel utilisateur

NETGEAR

NETGEAR FA311 - 10/100Mbps PCI Ethernet Interface... Manuel utilisateur

NETGEAR

NETGEAR GS748T - ProSafe Smart Switch Mode d’emploi

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur