NETGEAR ProSAFE FS728TLP Manuel

350 East Plumeria Drive

San Jose, CA 95134

USA

July 2013

202-11250-02

ProSAFE Fast Ethernet PoE Smart

Switch FS728TLP

Hardware Installation Guide

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product

at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website. For product updates and web

support, visit http://support.netgear.com.

Phone (US & Canada only): 1-888-NETGEAR.

Phone (Other Countries): Check the list of phone numbers at

http://support.netgear.com/general/contact/default.aspx.

Trademarks

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change

Revision History

Publication

Part Number Publish Date Comments

202-11250-02 July 2013 • Made minor corrections and revisions

• Added information about the product label

• Replaced references to the Software Administration Manual with

references to the web management user guide

202-11250-01 June 2013 First publication

Contents

Chapter 1 Introduction and Hardware Description

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

RJ-45 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

SFP GBIC Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Factory Defaults Button and Reset Button. . . . . . . . . . . . . . . . . . . . . . . . .12

Chapter 2 Installation

Step 1: Prepare the Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Step 2: Install the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Install the Switch on a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Install the Switch in a Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Step 3: Check the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Step 4: Connect Devices to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Step 5: Install an SFP GBIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Step 6: Apply AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Step 7: Manage the Switch through a Web Browser or

through the Smart Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 3 Troubleshooting

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Troubleshooting Suggestions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Network Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Switch Integrity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Autonegotiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Appendix A Physical and Technical Specifications

1. Introduction and Hardware

Description

The NETGEAR® ProSAFE® Fast Ethernet PoE Smart Switch FS728TLP is a state-of-the-art,

high-performance, IEEE-compliant network solution for users who require the flexibility of small

form-factor pluggable (SFP) GBIC slots and the ease of Power over Ethernet (PoE). To simplify

installation, the switch is shipped ready for use out of the box.

The chapter covers the following topics:

•Overview

•Switch Features

•Package Contents

•Front Panel

•Back Panel

•LEDs

•Product Label

•RJ-45 Ports

•SFP GBIC Modules

•Factory Defaults Button and Reset Button

Note: For more information about the topics covered in this manual, visit

the support website at support.netgear.com.

Note: Firmware updates with new features and bug fixes are made

available from time to time on downloadcenter.netgear.com. Some

products can regularly check the site and download new firmware,

or you can check for and download new firmware manually. If the

features or behavior of your product do not match what is described

in this guide, you might need to update your firmware.

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Overview

This hardware installation guide is for the NETGEAR ProSAFE Fast Ethernet PoE Smart

Switch FS728TLP. The switch provides twenty-four 10/100BASE-T ports, four

10/100/1000BASE-T ports, two of which function as combo ports, and two small form-factor

pluggable (SFP) GBIC slots, both of which function as combo ports. Power over Ethernet

(PoE) is supported on ports 1 through 12.

You can make high-speed connections using the Gigabit Ethernet ports. For example:

•Connecting switches to each other with high-speed links

•Connecting to a network backbone

•Linking to high-speed servers

•Providing 10/100/1000 Mbps copper and 100/1000 Mbps fiber connectivity

Note: In this guide, the NETGEAR ProSAFE Fast Ethernet PoE Smart

Switch FS728TLP is referred as the switch.

The switch also provides the benefit of administrative management with a complete package

of features to monitor, configure, and control the network. With the web management

interface, you can view the switch’s many features and use them in a simple and intuitive

manner. The switch’s management features include configuration for port and switch

information, VLAN for traffic control, port trunking for increased bandwidth, and Class of

Service (CoS) for traffic prioritization. Initial discovery of the switch on the network requires

the Smart Control Center, a utility that runs on a computer.

You can use the switch freestanding or rack-mounted in a wiring closet or equipment room.

The switch is IEEE-compliant and provides low latency for high-speed networking. All ports

can automatically negotiate to the highest speed. This capability makes the switch well suited

for environments that have a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet devices. In

addition, all RJ-45 ports operate in half- or full-duplex mode. The maximum segment length is

328 feet (100 meters) over a Category 5 twisted-pair cable.

You can use the switch as a desktop to build a small network that enables you to have

1000 Mbps access to a file server. With full duplex enabled, the switch port connected to the

server or computer can provide 2000 Mbps throughput.

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Figure 1. Example of a network configuration

Switch Features

The following list identifies the key features of the switch:

•Twenty-four RJ-45 10/100 Fast Ethernet switch ports.

•Four RJ-45 10/100/1000 Gigabit Ethernet switch ports, two of which (27T and 28T)

function as combo ports.

•Two small form-factor pluggable (SFP) GBIC slots, both of which (27F and 28F) function

as combo ports.

Combo ports are single ports with two physical connections, SFP fiber and RJ-45 copper.

The RJ-45 copper ports corresponding to the combo ports are the two 10/100/1000

autosensing Gigabit Ethernet switch combo ports. The SFP fiber ports corresponding to

the combo ports are the two SFP GBIC slots. If the two RJ-45 copper combo ports and

the two SFP fiber combo ports have devices connected, the devices that were connected

first take precedence. In other words, the combo ports function on a first-come,

first-served basis.

The following SFP GBICs are supported:

-1000BASE-SX (NETGEAR AGM731F)

-1000BASE-LX (NETGEAR AGM732F)

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

•The switch provides full compatibility with IEEE standards:

-IEEE 802.3i (10BASE-T)

-IEEE 802.3u (100BASE-TX, 100BASE-FX)

-IEEE 802.3x (full-duplex flow control)

-IEEE 802.3z (1000BASE-X)

-IEEE 802.3ab (1000BASE-T)

-IEEE 802.3af (Power over Ethernet)

-IEEE 802.3az (EEE)

•Autosensing and autonegotiating capabilities for all ports.

•Auto MDI/MIDX technology is supported on all ports.

•Automatic address-learning function to build the packet-forwarding information table. The

table contains up to 8 K Media Access Control (MAC) addresses.

•Full- and half-duplex functions for all 10/100/1000 Mbps ports.

•Store-and-forward transmission to remove corrupt packets from the network.

•Full-duplex IEEE 802.3x pause frame flow control.

•Active flow control to minimize packet loss and frame drops.

•Half-duplex back-pressure control.

•Per-port LEDs and system LEDs.

•Internal power supply.

•Standard 1U high, rack-mountable 19-inch chassis.

•Fan speed control.

•Support for the Power over Ethernet (PoE). PoE is supported on ports 1 through 12 with a

total power budget of 100W PoE. For example, the switch can support 15.4W for 6 ports

or 8W for 12 ports. The switch uses data pairs (RJ-45 1, 2, 3, and 6 PIN) to deliver the

power.

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Package Contents

The following figure shows the package contents of the switch.

350 East Plumeria Drive

San Jose, CA 95134

USA

June 2013

202-11251-01

350 East Plumeria Drive

San Jose, CA 95134

USA

June 2013

202-

1251-01

FS728TLP

Figure 2. Package contents

Verify that the package contains the following:

•NETGEAR ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

•Rubber footpads for tabletop installation

•Power cord

•Rack-mount kit for installing the switch in a 19-inch rack

•Smart Switch resource CD with the Smart Control Center utility and a link to the online

web management user guide.

•Installation guide

•Warranty support information card

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep

the carton, including the original packing materials, in case you need to return the product for

repair.

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Front Panel

The switch provides twenty-four 10/100BASE-T ports, four 10/100/1000BASE-T copper

ports, two of which (27T and 28T) are combo ports, and two small form-factor pluggable

(SFP) GBIC slots, both of which (27F and 28F) function as combo ports.

1 through 7,

see Figure 4

910 11

Combo ports

[27T, 28T, 27F, 28F]

Figure 3. Front panel

Figure 4. Close up left side of the front panel

The front panel contains the following components:

1. PoE Max LED

2. LED Mode LED

3. Mode selector button to switch the LEDs between PoE and Link/ACT information

4. Fan LED

5. Power LED

6. Recessed Reset button to reboot the switch

7. Recessed Factory Defaults button to restore the switch to the factory defaults

8. Twenty-four Link/ACT port LEDs that also function as PoE status LEDs for ports

1 through 12

9. Twenty-four RJ-45 10/100BASE-T ports

10. Four RJ-45 Gigabit Ethernet ports with corresponding Link/ACT LEDs

11. Two small form-factor pluggable (SFP) GBIC slots with corresponding Link/ACT LEDs

Introduction and Hardware Description

ProSAFE Fast Ethernet PoE Smart Switch FS728TLP

Back Panel

The back panel provides a 100–240 VAC/50–60 Hz universal power inlet, which is a standard

AC power receptacle that accommodates the supplied power cord.

Figure 5. Back panel

LEDs

The following table describes the LEDs.

Table 1. LED descriptions

Port LED Designation

(Not applicable, system LEDs)

PoE Max • Off. At least 7W of PoE power is available to connect

another powered device (PD).

•Solid yellow. Less than 7W of PoE power is available.

•Blinking yellow. The PoE Max LED was active in the

previous two minutes.

LED Mode • Solid green. The Link/ACT LEDs for the ports indicate

Link/ACT status.

•Solid yellow. The Link/ACT LEDs for the ports indicate

PoE status. The PoE status is displayed for ports 1 through

12 only.

Fan • Off. The fan is operating normally.

•Solid yellow. A fan failure has occurred.

Power • Off. Power is disconnected.

•Solid green. Power is supplied to the switch and the

switch is operating normally.

•Solid yellow. The switch is starting and not yet ready for

operation.

Ports 1 through 12 (one LED

for each PoE port)

Note: The LED mode

selectorbuttonneedsto bein

the PoE mode.

PoE • Off. No PoE powered device (PD) is connected.

•Solid green. The PoE PD is connected and the port is

supplying power successfully.

•Solid yellow. One of the following failures prevented

power from being supplied to the PD:

- Short circuit on the PoE power circuit

- PoE power demand exceeds the available power

- PoE current exceeds classification of the PD

- Out of proper voltage band (44–57 VDC)

Table des matières

Autres manuels NETGEAR Routeur réseau

NETGEAR

NETGEAR SXK30 Manuel utilisateur

NETGEAR

NETGEAR DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall... Manuel utilisateur

NETGEAR

NETGEAR RAX49 Manuel utilisateur

NETGEAR

NETGEAR RAX5 Manuel utilisateur

NETGEAR

NETGEAR FE104 - Hub Manuel utilisateur

NETGEAR

NETGEAR RP334 Manuel utilisateur

NETGEAR

NETGEAR DG834 - ADSL Firewall Router Fiche technique

NETGEAR

NETGEAR Nighthawk AXE11000 Manuel utilisateur

NETGEAR

NETGEAR ProSafe Plus FS116E Manuel utilisateur

NETGEAR

NETGEAR C6220 Manuel utilisateur

NETGEAR

NETGEAR Nighthawk AX4 Manuel utilisateur

NETGEAR

NETGEAR Orbi RBE971 Manuel utilisateur

NETGEAR

NETGEAR Orbi Pro SXS80 Manuel utilisateur

NETGEAR

NETGEAR MR814 - 802.11b Cable/DSL Wireless Router Guide de l'utilisateur

NETGEAR

NETGEAR Nighthawk AX6 Manuel utilisateur

NETGEAR

NETGEAR XEB1004 - 85 Mbps Powerline EN Switch Manuel utilisateur

NETGEAR

NETGEAR MVBR1210C Manuel utilisateur

NETGEAR

NETGEAR WNDR4300 Feuille d'instructions

NETGEAR

NETGEAR Nighthawk M6 Manuel utilisateur

NETGEAR

NETGEAR D6400 Manuel utilisateur

NETGEAR

NETGEAR MR1100EE Manuel utilisateur

NETGEAR

NETGEAR R6300v2 Manuel utilisateur

NETGEAR

NETGEAR ProSafe FVS318v3 Manuel utilisateur

NETGEAR

NETGEAR FS605 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur