NETGEAR FVS328 - ProSafe VPN Firewall Manuel utilisateur

Start Here

Follow these instructions to set up your router.

Verify That Basic Requirements Are Met

Assure that the following requirements are met:

• You have your broadband Internet service settings handy.

• The computer is configured to obtain an IP address

automatically via DHCP. For instructions on how to do this,

please see the Reference Manual on the Model FVS328

Resource CD.

1. CONNECT THE FIREWALL

a. Turn off your computer and cable or DSL modem.

b. Disconnect the Ethernet cable (A) which connects from

your computer to the broadband modem.

c. Securely insert the Ethernet cable from your broadband

modem into the Internet port (B) on the FVS328.

d. Securely insert one end of the Ethernet cable that came with

your firewall into a LAN port on the router such as LAN

port 7 (C), and the other end into the Ethernet port of your

computer (D).

2. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE

Warning: Failure to restart your network in the correct

sequence could prevent you from connecting to the Internet.

a. First, turn on the broadband modem and wait 2 minutes.

b. Now, turn on your firewall.

c. Last, turn on your computer.

Note: If software usually logs you in to the Internet, do not

run that software or cancel it if it starts automatically.

d. Check the status lights and verify the following:

•Power: The power light goes on when your turn the

firewall on.

•Test: The test light turns on, then goes off after less than

a minute.

•Local: A Local light on the router is lit. If no Local

lights are lit, check that the Ethernet cable connecting

the powered on computer to the router is securely

attached at both ends.

•Internet: The Internet light on the firewall is lit. If the

Internet light is not lit, make sure the Ethernet cable is

securely attached to the firewall Internet port and the

powered on modem.

3. LOG IN TO THE FIREWALL

a. From your PC, launch your Internet browser.

b. Connect to the firewall by typing http://192.168.0.1 in the

address field of Internet Explorer or Netscape®Navigator.

c. Enter admin for the router user name and password for the

router password, both in lower case letters.

d. After logging in to the router, you will see the Internet

connection Setup Wizard on the settings main page.

Broadband modem

MODEM 12VDC 1.2A

87654321

LOCA L

10/100M

INTERN ET

Internet Port

Broadband modem

MODEM 12VDC 1.2A

87654321

LOCA L

10/100M

INTERNET

Local Port

Broadband modem

INTERN ET LO CA L

ACT

1234 5678

LNK

LNK/ACT

100

Broadband ProSafe VPN Firewall with Dial Backup

MODEL FVS328

PWR TEST Modem

Power Test Internet Port Local Port 7

4. RUN THE SETUP WIZARD TO CONNECT TO THE INTERNET

a. You are now connected to the router. If you do not see the

menu above, click the Setup Wizard link on the upper left of

the main menu.

b. Choose NAT or Classical Routing. Typically, NAT is used.

NAT automatically assigns private IP addresses

(192.168.0.x) to LAN connected devices. Classical routing

lets you directly manage the IP addresses the FVS328 uses.

c. Click Next to proceed. Input your ISP settings, as needed.

d. At the end of the Setup Wizard, click the Test button to

verify your Internet connection and register your product. If

you have trouble connecting to the Internet, use the

Troubleshooting Tips below to correct basic problems, or

refer to the Reference Manual on the CD.

You are now connected to the Internet!

Troubleshooting Tips

Here are some tips for correcting simple problems that prevent with

you from connecting to the Internet or connecting to the firewall.

Be sure to restart your network in the correct sequence.

Follow this sequence. Turn off the modem, firewall, and

computer. Turn on the modem first and wait two minutes. Next

turn on the firewall, and finally the computer.

Make sure the Ethernet cables are securely plugged in.

• For each powered on computer connected to the firewall with a

securely plugged in Ethernet cable, the corresponding firewall

Local port status light will be lit. The label on the bottom of the

firewall identifies the number of each Local port.

• The Internet port status light on the firewall will be lit if the

Ethernet cable from the firewall to the modem is plugged in

securely and the modem and firewall are turned on.

Make sure the network settings of the computer are correct.

LAN connected computers must be configured to obtain an IP

address automatically via DHCP, unless you have turned NAT

off and are managing the IP addresses directly. For instructions

on these configuration settings, please see the Reference Manual

on the Model FVS328 Resource CD.

Technical Support

Thank you for selecting NETGEAR products.

To register, point your browser to this location:

http://www.NETGEAR.com/register

Go to http://www.NETGEAR.com/support to browse for additional

NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or

other countries.

Other brand and product names are trademarks or registered trademarks of their

respective holders. Information is subject to change without notice.

201-10082-01 December 2003

Autres manuels pour FVS328 - ProSafe VPN Firewall

Table des matières

Autres manuels NETGEAR Routeur réseau

NETGEAR

NETGEAR Nighthawk XR1000v2 Manuel utilisateur

NETGEAR

NETGEAR RM356 RM356 RM356 Manuel utilisateur

NETGEAR

NETGEAR MBRN3000 Manuel utilisateur

NETGEAR

NETGEAR Orbi RBR860 Manuel utilisateur

NETGEAR

NETGEAR Orbi RBK23 Manuel utilisateur

NETGEAR

NETGEAR ETHERNET SWITCH SW108 Manuel utilisateur

NETGEAR

NETGEAR ProSafe FVS318N Manuel utilisateur

NETGEAR

NETGEAR WGE101 Manuel utilisateur

NETGEAR

NETGEAR DGN2000 - Wireless Router Manuel utilisateur

NETGEAR

NETGEAR RP614 v4 Manuel utilisateur

NETGEAR

NETGEAR ME101 - Wireless EN Bridge Network Converter Manuel utilisateur

NETGEAR

NETGEAR Nighthawk XR700 Manuel utilisateur

NETGEAR

NETGEAR RP614 - Web Safe Router Manuel utilisateur

NETGEAR

NETGEAR Nighthawk X6S Manuel utilisateur

NETGEAR

NETGEAR orbi RBK652S Manuel utilisateur

NETGEAR

NETGEAR WAG302 Manuel utilisateur

NETGEAR

NETGEAR R6300 Manuel utilisateur

NETGEAR

NETGEAR Nighthawk D7000 Manuel utilisateur

NETGEAR

NETGEAR WNDR4500 Manuel utilisateur

NETGEAR

NETGEAR RP334 Manuel utilisateur

NETGEAR

NETGEAR MBR1515 Manuel utilisateur

NETGEAR

NETGEAR DG834GUV5 Manuel utilisateur

NETGEAR

NETGEAR Orbi RBR20 Manuel utilisateur

NETGEAR

NETGEAR MVBR1210C Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur