NetApp H410S Manuel du propriétaire

H410S and H610S hardware information

Element Software

NetApp

March 11, 2022

This PDF was generated from https://docs.netapp.com/us-en/element-

software/hardware/task_h410s_h610s_install.html on March 11, 2022. Always check docs.netapp.com for

the latest.

Table of Contents

H410S and H610S hardware information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Find more information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Install H-series storage nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Replace a H410S node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê8

Replace a H610S node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê12

Replace drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê15

Replace a power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê18

H410S and H610S hardware information

You can find information about installing and maintaining H-series storage nodes.

Here are the links to the installation and maintenance content:

•Install H-series storage nodes

•Replace a H410S node

•Replace a H610S node

•Replace drives

•Replace a power supply unit

Find more information

•NetApp SolidFire Resources Page

•Documentation for earlier versions of NetApp SolidFire and Element products

Install H-series storage nodes

Before you get started with your all-flash storage system, you should install and set up

the storage nodes correctly.

See the poster for a visual representation of the instructions.

•Workflow diagrams

•Prepare for installation

•Install the rails

•Install and cable the nodes

•Configure the nodes

•Create a cluster

Workflow diagrams

The workflow diagrams here provide a high-level overview of the installation steps. The steps vary slightly

depending on the H-series model.

H410S

H610S

The terms "node" and "chassis" are used interchangeably in the case of H610S, because node

and chassis are not separate components unlike in the case of a 2U, four-node chassis.

Prepare for installation

In preparation for installation, inventory the hardware that was shipped to you, and contact NetApp Support if

any of the items are missing.

Ensure that you have the following items at your installation location:

•Rack space for the system.

Node type Rack space

H410S nodes Two rack unit (2U)

H610S nodes One rack unit (1U)

•SFP28/SFP+ direct-attach cables or transceivers

•CAT5e or higher cables with RJ45 connector

•A keyboard, video, mouse (KVM) switch to configure your system

•USB stick (optional)

The hardware that is shipped to you depends on what you order. A new 2U, four-node order

includes the chassis, bezel, slide rail kit, drives, storage nodes, and power cables (two per

chassis). If you order H610S storage nodes, the drives come installed in the chassis.

While installing the hardware, ensure that you remove all packing material and wrapping from

the unit. This will prevent the nodes from overheating and shutting down.

Install the rails

The hardware order that was shipped to you includes a set of slide rails. You will need a screwdriver to

complete the rail installation. The installation steps vary slightly for each node model.

Install hardware from the bottom of the rack up to the top to prevent the equipment from toppling

over. If your rack includes stabilizing devices, install them before you install the hardware.

•H410S

•H610S

H410S

H410S nodes are installed in 2U, four-node H-Series chassis, which is shipped with two sets of adapters. If

you want to install the chassis in a rack with round holes, use the adapters appropriate for a rack with round

holes. The rails for H410S nodes fit a rack between 29 inches and 33.5 inches in depth. When the rail is fully

contracted, it is 28 inches long, and the front and rear sections of the rail are held together by only one screw.

If you install the chassis onto a fully contracted rail, the front and rear sections of the rail might

separate.

Steps

1. Align the front of the rail with the holes on the front post of the rack.

2. Push the hooks on the front of the rail into the holes on the front post of the rack and then down, until the

spring-loaded pegs snap into the rack holes.

3. Attach the rail to the rack with screws. Here is an illustration of the left rail being attached to the front of the

rack:

4. Extend the rear section of the rail to the rear post of the rack.

5. Align the hooks on the rear of the rail with the appropriate holes on the rear post ensuring that the front and

the back of the rail are on the same level.

6. Mount the rear of the rail onto the rack, and secure the rail with screws.

7. Perform all the above steps for the other side of the rack.

H610S

Here is an illustration for installing rails for an H610S storage node:

There are left and right rails on the H610S. Position the screw hole towards the bottom so that

the H610S thumbscrew can secure the chassis to the rail.

Install and cable the nodes

You install the H410S storage node in a 2U, four-node chassis. For H610S, install the chassis/node directly

onto the rails in the rack.

Remove all the packing material and wrapping from the unit. This prevents the nodes from

overheating and shutting down.

•H410S

•H610S

H410S

Steps

1. Install the H410S nodes in the chassis. Here is a rear-view example of a chassis with four nodes installed:

Use caution while lifting the hardware and installing it into the rack. An empty two rack unit

(2U), four-node chassis weighs 54.45 lb (24.7 kg) and a node weighs 8.0 lb (3.6 kg).

2. Install the drives.

3. Cable the nodes.

If the airflow vents at the rear of the chassis are blocked by cables or labels, it can lead to

premature component failures due to overheating.

◦Connect two CAT5e or higher cables in ports A and B for management connectivity.

◦Connect two SFP28/SFP+ cables or transceivers in ports C and D for storage connectivity.

◦(Optional, recommended) connect a CAT5e cable in the IPMI port for out-of-band management

connectivity.

4. Connect the power cords to the two power supply units per chassis and plug them into 240V PDU or power

outlet.

5. Power on the nodes.

It takes approximately six minutes for the node to boot.

H610S

Steps

1. Install the H610S chassis. Here is an illustration for installing the node/chassis in the rack:

Use caution while lifting the hardware and installing it into the rack. An H610S chassis

weighs 40.5 lb (18.4 kg).

2. Cable the nodes.

If the airflow vents at the rear of the chassis are blocked by cables or labels, it can lead to

premature component failures due to overheating.

◦Connect the node to a 10/25GbE network using two SFP28 or SFP+ cables.

◦Connect the node to a 1GbE network using two RJ45 connectors.

◦Connect the node to a 1GbE network using an RJ-45 connector in the IPMI port.

◦Connect both power cables to the node.

3. Power on the nodes.

It takes approximately five minutes and 30 seconds for the node to boot.

Configure the nodes

After you rack and cable the hardware, you are ready to configure your new storage resource.

Steps

1. Attach a keyboard and monitor to the node.

2. In the terminal user interface (TUI) that is displayed, configure the network and cluster settings for the node

by using the on-screen navigation.

You should get the IP address of the node from the TUI. You need this when you add the

node to a cluster. After you save the settings, the node is in a pending state, and can be

added to a cluster. See the <insert link to Setup section>.

3. Configure out-of-band management using the Baseboard Management Controller (BMC). These steps

apply only to H610S nodes.

a. Use a web browser and navigate to the default BMC IP address: 192.168.0.120

b. Log in using root as the username and calvin as the password.

c. From the node management screen, navigate to Settings > Network Settings, and configure the

network parameters for the out-of-band management port.

See this KB article (log in required).

Create a cluster

After you add the storage node to your installation and configure the new storage resource, you are ready to

create a new storage cluster

Steps

1. From a client on the same network as the newly configured node, access the NetApp Element software UI

by entering the node’s IP address.

2. Enter the required information in the Create a New Cluster window. See the setup overview for more

information.

Find more information

•NetApp SolidFire Resources Page

•Documentation for earlier versions of NetApp SolidFire and Element products

Replace a H410S node

You should replace a storage node in the event of CPU failure, Radian card problems,

other motherboard issues, or if it does not power on. The instructions apply to H410S

storage nodes.

Alarms in the NetApp Element software UI alert you when a storage node fails. You should use the Element UI

to get the serial number (service tag) of the failed node. You need this information to locate the failed node in

the cluster.

Here is the back of a two rack unit (2U), four-node chassis with four storage nodes:

Autres manuels pour H410S

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels NetApp Stockage

NetApp

NetApp DS4243 Manuel

NetApp

NetApp FAS8300 Manuel utilisateur

NetApp

NetApp FAS500f Manuel utilisateur

NetApp

NetApp FAS2700 Series Manuel utilisateur

NetApp

NetApp AFF A200 Manuel de l'opérateur

NetApp

NetApp NearStore R100 Manuel utilisateur

NetApp

NetApp StorageGRID Webscale SG5700 Series Feuille d'instructions

NetApp

NetApp SteelStore 30 Series Manuel utilisateur

NetApp

NetApp FAS8300 Manuel

NetApp

NetApp AFF A400 Manuel utilisateur

NetApp

NetApp FAS8300 Manuel utilisateur

NetApp

NetApp FAS8700 Feuille d'instructions

NetApp

NetApp DS4243 Instructions d'installation et d'entretien

NetApp

NetApp StorageGRID Webscale SG6000 Series Manuel utilisateur

NetApp

NetApp AFF A250 Manuel utilisateur

NetApp

NetApp HCI Manuel utilisateur

NetApp

NetApp H600S Series Manuel

NetApp

NetApp DS224C Manuel utilisateur

NetApp

NetApp FAS2700 Series Manuel

NetApp

NetApp DS460C Manuel utilisateur

NetApp

NetApp AFF A320 Manuel utilisateur

NetApp

NetApp AFF A800 Manuel utilisateur

NetApp

NetApp FAS25 Series Manuel utilisateur

NetApp

NetApp FAS22 Series Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur