Net1 R-90 Manuel utilisateur

User Manual

Gateway R-90

CDMA 2000 EV-DO Rev B Router

R-90 Series

Important Notice

Due to the nature of wireless communications, transmission and reception of data can never be guaranteed.

Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of

data are rare when wireless devices such as the router are used in a normal manner with a well-constructed

network, the router should not be used in situations where failure to transmit or receive data could result in

damage of any kind to the user or any other party, including but not limited to personal injury, death or loss

of property. Axesstel accepts no responsibility for damages of any kind resulting from delays or errors in

data transmitted or received using the Axesstel router or for failure of the Axesstel router to transmit or

receive such data.

Safety Precautions

Do not operate the router:

In areas where blasting is in progress

Where explosive atmospheres may be present

Near medical equipment

Near life support equipment or any equipment that may be susceptible to any form of radio

interference. In such areas, the router MUST BE POWERED OFF. The Axesstel router can transmit

signals that could interfere with this equipment.

Do not operate the router in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the

router MUST BE POWERED OFF. When operating, the router can transmit signals that could interfere with

various onboard systems.

Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is

open. The router may be used at this time.

The driver or operator of any vehicle should not operate the router while in control of a vehicle. Doing so will

detract from the driver or operator’s control and operation of that vehicle. In some states and provinces,

operating such communications devices while in control of a vehicle is an offense.

Limitation of Liability

The information in this manual is subject to change without notice and does not represent a commitment on

the part of Axesstel.

AXESSTEL SPECIFICALLY DISCLAIMS LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,

GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT

NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE

ARISING OUT OF THE USE OR INABILITY TO USE ANY AXESSTEL PRODUCT, EVEN IF AXESSTEL

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR

FOR CLAIMS BY ANY THIRD PARTY.

Notwithstanding the foregoing, in no event shall Axesstel aggregate liability arising under or in connection

with the Axesstel product, regardless of the number of events, occurrences, or claims giving rise to liability.

R-90 Series

TABLE OF CONTENTS

1Introduction ........................................................................................................... 4

2Product Overview ................................................................................................... 4

2.1 Placement of your R-90................................................................................... 5

3Using your Router................................................................................................... 6

3.1 Package Contents ........................................................................................... 6

3.2 Router Interfaces............................................................................................ 6

3.3 Power LED ..................................................................................................... 6

3.4 Signal Strength LED........................................................................................ 7

3.5 Connect LED .................................................................................................. 7

3.6 Network LED .................................................................................................. 7

3.7 Wi-Fi LED....................................................................................................... 7

3.8 Other Features ............................................................................................... 7

3.9 Rechargeable Battery...................................................................................... 8

3.10 Setting up your Hardware ............................................................................... 9

3.11 Connecting and Configuring your Router ........................................................ 10

4Web Manager Options........................................................................................... 11

4.1 Basic Wireless Settings.................................................................................. 14

4.2 Router Status ............................................................................................... 16

4.3 Network Information..................................................................................... 17

4.4 System Settings............................................................................................ 18

4.5 Advanced Wireless Settings........................................................................... 20

4.6 Multi Port Forwarding.................................................................................... 21

4.7 Single Port Forwarding.................................................................................. 22

4.8 Firewall ........................................................................................................ 23

4.9 LAN MAC Filtering......................................................................................... 24

4.10 WAN Setup .................................................................................................. 25

4.11 LAN IP Setup................................................................................................ 26

4.12 Dynamic DNS ............................................................................................... 28

4.13 Static Routes ................................................................................................ 29

4.14 UPnP Settings............................................................................................... 30

4.15 CDMA Settings.............................................................................................. 31

4.16 VoIP Account Settings................................................................................... 32

5VoIP Call Functions ............................................................................................... 33

5.1 Activating Voice over IP ................................................................................ 33

5.2 Placing Voice Calls ........................................................................................ 33

5.3 Receiving Voice Calls .................................................................................... 33

5.4 Call Forwarding ............................................................................................ 33

5.5 Restricting Caller Line Identification ............................................................... 34

6Troubleshooting.................................................................................................... 35

7Technical Specification .......................................................................................... 36

8Certification.......................................................................................................... 37

R-90 Series

1 Introduction

Thank you for purchasing the Net1 R-90 EV-DO router with Voice over IP (VoIP). This user manual will help

you setup, configure and outline best practices for maximizing your wireless home network performance with

the router.

2 Product Overview

In minutes, you will be able to connect your computers to the Internet, share your Internet connection and

network your computers. And you will be able to make a call using VoIP. The following is a list of features

that make your new Net1 EV-DO router an ideal solution for your home or small office network.

Implementation of these features depends on the particular service provider and account features you have

chosen.

Some features described in this manual may not be supported by your service provider or may not be

available with your network account. For details of the services and accounts available, contact your service

provider.

VoIP Calling

Your router (R-90) features a Voice over Internet Protocol (VoIP) function that allows you to make voice calls

over a VoIP network by simply connecting a wired, landline phone to your network-connected router.

Plug-and-Play

Your router was factory-set for compatibility with a particular service provider. Thus, your router

operates on radio channels and enables services specific to your network service provider. Once

your router has been activated on your service provider’s network, you can connect to the Internet.

After your router is activated, connect it to your computer using the Ethernet (RJ-45) cable or via Wi-

Fi. You are now ready to use the Internet.

Web-Based Advanced User Interface

You can easily setup the router’s advanced functions through your web browser and without having to install

additional software onto your computer. There are no drivers to install and, you can easily make changes

and perform setup functions from any computer that is connected to your R-90

NAT IP Address Sharing

Support for VPN Pass Through

Built in Dynamic Host Configuration Protocol (DHCP)

Integrated 802.11b/g/n Wireless Access Point

MAC Address Filtering

Integrated 10/100 4-Port Switch

The R-90 has a built-in, 4-port network switch to allow your wired computers to share printers, data and MP3

files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of

connected devices. The switch will transfer data between computers and the Internet simultaneously without

interrupting or consuming resources.

Integrated 802.11 b/g/n Wireless Access Point

The R-90 supports Wi-Fi modes b/g and n. Your router as default is set to Wi-Fi mode g. To use mode n

you can change this by logging into the web interface (instructions are in section 3.10). Although, please

ensure that your Wi-Fi card supports n mode.

R-90 Series

2.1 Placement of your R-90

Place your R-90, the central connection point of your network, as close as possible to windows or in rooms

at the outer side of your house. If you also use the Wi-Fi feature of the R-90, it should be placed near the

centre of your wireless network devices.

To achieve the best wireless network coverage:

Ensure that your R-90’s networking antennas are parallel to each other, and are positioned vertically

(toward the ceiling). If your R-90 itself is positioned vertically, point the antennas as much as possible in

an upward direction. In multi-storey homes, place the R-90 on an upper floor.

Avoid placing your R-90 near devices that may emit radio “noise,” such as microwave ovens. Dense

objects can interfere with wireless communication

If your wireless signal seems weak in some areas, try to move the R-90 to another location while

observing the signal strength indicator

R-90 Series

3 Using your Router

3.1 Package Contents

R-90 EV-DO Rev B router

Antennas

RJ-45 Ethernet Networking Cable

Power Supply (230V)

Car Charger (12V)

Quick Installation Guide

CD with Complete User Manual

3.2 Router Interfaces

The R-90 is designed to be placed on a desktop or wall mounted. All the ports at the back of the router are

for better organization and utility. The LED indicators are easily visible on the top of the router to provide you

with information about network activity and status.

3.3 Power LED

LED Colour

AC Mode

Battery Mode

OFF

No Power

Blue Solid

Adaptor Connected

Fully Charged

Blue Blinking

(3s)

In Charging

Blue Blinking

(1s)

Low Level Charged

R-90 Series

3.4 Signal Strength LED

This LED indicates the signal strength of the CDMA network serving the router.

LED Colour

Status

OFF

No CDMA signal

Blue

Strongest Level

Blue Blinking

(3s)

Medium Level

Blue Blinking

(1s)

Low Level

3.5 Connect LED

This LED informs you that the router is connected to a wireless network and that your user ID and password

have been validated.

LED Colour

Status

OFF

No connection

Blue

- In Data use: Connected

- In VoIP call use: In use

3.6 Network LED

This LED informs you that the router is tuned to the wireless network. Your router is programmed to search

and use an EV-DO network.

LED Colour

Status

OFF

No Network

Blue

EV-DO

3.7 Wi-Fi LED

This LED indicates the status of your Wi-Fi connection.

LED Colour

Status

OFF

No Wi-Fi

Blue Solid

Wi-Fi network within R-90 activated

Blue Blinking

Data passing through Wi-Fi

3.8 Other Features

(6) Network connections to Computers (RJ-45/Ethernet)

(7) Phone line (RJ-11)

(8) Power On/Off Switch

(9) Power Jack

R-90 Series

3.9 Rechargeable Battery

The R-90 comes with the rechargeable battery already pre-installed. It is natural that over time the battery

performance will degrade. If you need to remove and replace your battery please follow the instructions

below

Before removing or inserting the battery, please ensure that you disconnect the power supply, and move the

power switch on the R-90 to the OFF position.

Removing / Replacing the Battery

①Open the battery cover on the bottom by sliding the cover down towards you.

②Disconnect / Connect the DC power cable to the unit marked below.

③Close the battery cover

R-90 Series

3.10 Setting up your Hardware

1 Make sure your router is not connected to any power source and that all the LEDs are OFF.

2 How to setup the antennas for maximized performance:

①Antennas are located on both sides of the router.

②Attach the antennas to the back of the router

③Hand tighten the antennas so that they are securely attached to the router

3 Locate the power supply that is included with your router. Plug the power supply’s small connector into

the power port on the router (6). Plug the power supply into an empty power outlet.

4 Switch on the router (8). Look at the Power LED on top of the router and make sure the lights are ON.

5 Wait for a few seconds while the router searches for network service. When the router finds a suitable

network, the Signal LED turns blue and will flash dependent upon the strength of the acquired signal.

Refer to the Signal Strength LED description for more details.

6 Locate the Ethernet cable that is included with your router. Plug one end of this cable into ANY

Ethernet port on your router. Plug the other end of the cable into the networking port on your

computer. Alternatively connect to the router through Wi-Fi (see below).

R-90 Series

3.11 Connecting and Configuring your Router

Each router is factory built for use with a particular service provider. Thus, each router is set to use particular

radio channels and to enable services specific to a provider.

Once your router has been activated with the network, connect your computer to the router using the

provided Ethernet (RJ-45) cable or Wi-Fi. You are now ready to use the Internet.

3.11.1 Connecting with Wi-Fi

When connecting through Wi-Fi please ensure you try to connect to the correct R-90 as each device has a

unique SSID. The SSID can be found on the sticker, which is located on the bottom of the router. Please

note that the last 4 characters are random.

You will also need to enter the unique password for your router. This again can be found on the sticker on

the bottom of your router

*Please note that the last 4 characters of the SSID is a random combination of both letters and numbers and

will differ from the SSID that is shown on your device label

Table des matières

Manuels Autre populaires d'autres marques

GO Industries

GO Industries 38017 Manuel utilisateur

Cissell

Cissell 30LBCMAN2 Manuel utilisateur

RIDGID

RIDGID K-60SP Manuel utilisateur

Gage Bilt

Gage Bilt GB751SH-5 Manuel utilisateur

OVE

OVE SIERRA 60 Manuel utilisateur

ReelCraft

ReelCraft 7800 OLB21 Manuel utilisateur

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuel utilisateur

ROBLIN

ROBLIN DROP Guide de l'utilisateur

EMG

EMG EMG-ACB BARREL Manuel de service

MiniSolar

MiniSolar MT-150 Manuel utilisateur

Parkside

Parkside PSZ 250 B2 Manuel utilisateur

ABB

ABB REM 610 Manuel du produit

Parkside

Parkside 55992 Manuel du propriétaire

Skyjacker

Skyjacker F250 Manuel utilisateur

IBM

IBM IBM SYSTEM Z Guide d'installation

Grech Motors

Grech Motors G28 Manuel utilisateur

NOVAK

NOVAK BATTERY CARE SHEET Mode d’emploi

Telemotive

Telemotive blue PiraT Mini Guide de l'utilisateur