Net Optics IBYPASS 40G Manuel utilisateur

Quick Install Guide

800-0228-001 Rev A 11/13

I2BP-40

PLEASE READ THESE LEGAL NOTICES CAREFULLY.

By using the Net Optics iBypass 40G Switch, you agree to the terms and conditions of usage set forth by Net Optics, Inc.

No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics

retains all intellectual property rights associated with the technology described in this manual. This manual is intended

to assist with installing Net Optics products into your network.

Trademarks and Copyrights

Inc. Additional company and product names may be trademarks or registered trademarks of the individual companies

and are respectfully acknowledged.

Additional Information

Net Optics, Inc. reserves the right to make changes in specications and other information contained in this document

without prior notice. Every effort has been made to ensure that the information in this document is accurate.

Contents

iBypass 40G Switch Content 4

iBypass 40G Switch Overview 5

Connect Power 8

Connect PC to Console Port 10

Congure the iBypass 40G IP 12

Connect to the Network 14

Connect Monitoring Tools 15

iBypass 40G Switch Content

This guide provides the initial steps to set up and congure the Net Optics iBypass

40G Switch.

Carefully unpack the contents and verify you have the following components:

• iBypass 40G Switch

• 3-meter RJ45, CAT 5e 4-pair

• RJ45 to DB9 Console Port to PC cable

• Long Ear Extender and Short Ear Extender for rack mounting

• Two External Power Supplies (12VDC, 9A, 108W)

• Eight Phillips screws

• iBypass 40G Switch Quick Install Guide (this document)

• iBypass 40G Switch User Guide (on CD)

• End User Agreement, Registration Card and Extended Warranty (if purchased)

The QSFP+ transceiver kits and 40G MTP cables are sold and shipped separately.

Contact Net Optics Technical Assurance Center if any component is missing or

damaged. Contact details are at the back of this guide.

iBypass 40G Switch Overview

2x16 Character Display

Network

Ports

Monitor

Ports

Bypass, Tap, Power

LEDs

Activity & Alarm

LEDs

Management

Port

Console

Port

Figure 1 - Front View

• Console Port (RJ45) and Management Port (RJ45)

• 2 x 40G Monitor Ports (uses QSFP+ transceivers )

• 2 x 40G Network Ports (MTP Connectors)

Figure 2 - Rear View

• Hot swapple fans and replaceable power module

Step 1

Rack Mount iBypass 40G Switch

Install the iBypass 40G Switch into a standard 19-inch equipment rack. The switch is

designed to occupy one rack unit. Do the following to install the iBypass 40G Switch

into an equipment rack:

1. Remove the Ear Extenders and screws from the shipping bag.

2. Attach the Long Ear Extender to the switch if you are only mounting one switch

or attach the Short Ear Extender between two switches if you are mounting two

switches. See Figure 3.

3. Slide the switches in place in the rack.

4. Fasten the switches in place at the front panel ears using the Phillips screws.

5. Make sure the rack is properly electrically grounded.

Grounding

Ground the chassis to the rack by connecting a 14 AWG minimum ground wire with a

#8 ring lug to the ground connection on the rear of the chassis. Terminate the other

end of the ground wire to the rack ground bus bar.

Long Ear Extender

for one switch

Short Ear Extender

binds two switches

Figure 3 - Use Ear Extenders in Rack Mount Preparation

Step 2

Connect Power

Ensure the iBypass 40G Switch is grounded before connecting power. Do the

following to connect and apply power to the iBypass 40G Switch:

1. Plug one of the supplied power cords to a power connector located at the rear

of the chassis. Plug the other end to a power source. See Figure 4.

2. For redundancy, plug the other power cord to the iBypass 40G. Plug the other

end to a source independent from the rst power source.

The Power LEDs on the front illuminate.

Switch Default Settings

The iBypass 40G Switch ships with the following default system settings:

IP Address: 10.60.4.180 Threshold Port A: 80%

Netmask: 255.0.0.0 Threshold Port B: 80%

Gateway: 10.0.0.1 Username: admin

Password: netoptics

Figure 4 - Power Connections

Step 3

Connect Options

You have two ways of logging in to the iBypass 40G switch.

Option 1 - Connect PC to Management Port

1. Connect a PC whose IP address is on the same subnet as the iBypass switch.

The default address on the switch is:

IP Address: 10.60.4.180 Mask - 255.0.0.0 Gateway - 10.0.0.1

2. Connect a Cat 5e cable from your PC’s Ethernet port to the iBypass

Management port. See Figure 5.

3. Open a terminal window on the PC and ping 10.60.4.180 to conrm the

connection.

4. After you have conrmed that you have a connection, you can log in via SSH at

the terminal prompt, or enter the default address into the browser URL. Go to

the Assign IP in Web UI section if you want to log in through the Web UI. Go

to the next step if you want to log in to the CLI.

5. At the terminal window prompt, type ssh [email protected]. Enter

password netoptics. The Net Optics prompt appears.

6. At the prompt, enter admin for the user and netoptics for the password.

7. Change the password for the admin account by entering the following

command at the prompt:

modify user password admin <new_passwd> <re-enter_passwd>

where <new_passwd> is the new password for the admin account and

Table des matières

Autres manuels Net Optics Changer

Net Optics

Net Optics Director xStream Pro Manuel utilisateur

Net Optics

Net Optics 4xN 10 Manuel utilisateur

Net Optics

Net Optics Director Manuel utilisateur

Net Optics

Net Optics 10/100/1000 Manuel utilisateur

Net Optics

Net Optics IBPO-HBSR-XFP Manuel utilisateur

Net Optics

Net Optics iBypass Manuel utilisateur

Net Optics

Net Optics Director Manuel utilisateur

Net Optics

Net Optics iMatrix ISW-CU3-S4x16 Manuel utilisateur

Net Optics

Net Optics 10/100/1000 Manuel utilisateur

Net Optics

Net Optics BPO-HBSX-LC Manuel utilisateur

Net Optics

Net Optics Director Manuel utilisateur

Net Optics

Net Optics PA-CU-AR Manuel utilisateur

Net Optics

Net Optics N-IDP-POBPSX-001, N-IDP-POBPLX Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Net Optics iBYPASS 40G Manuel utilisateur

Manuels Changer populaires d'autres marques