Neptronic BM000 Manuel utilisateur

BM Series Actuators

Specification and Installation Instructions

BM-181119

Technical

Data

BM000

BM060

BM000F

BM060F

BM000FF

BM060FF

BM020

BM080

BM020F

BM080F

BM020FF

BM080FF

Fail safe1

Yes

Power

consumption

15VA

Peak,6VA

24VA

Peak,15VA

24VA

Peak,15VA

15VA

Peak,6VA

24VA

Peak,15VA

24VA

Peak,15VA

Torque

50 in.lb. [5.6 Nm]

at rated voltage

35 in.lb. [3.9 Nm] at

rated voltage

25 in.lb. [2.8 Nm] at

rated voltage

50 in.lb. [5.6 Nm]

at rated voltage

35 in.lb. [3.9 Nm] at

rated voltage

25 in.lb. [2.8 Nm] at

rated voltage

Running time

through 90º

20 to 30 sec

torque dependant

3.5 to 4.5 sec

torque dependant

1.5 to 2.5 sec

torque dependant

20 to 30 sec

torque dependant

3.5 to 4.5 sec

torque dependant

1.5 to 2.5 sec

torque dependant

Auxiliary

switches

Yes (2)

Ingress

protection

IP22 equivalent to Nema type 2,

IP54 equivalent to Nema type 3R if water tight inlet bushings

(not supplied NEP617) are installed

IP22 equivalent to Nema type 2

Feedback

4 to 20 mA or 2 to 10 Vdc adjustable

Power supply

22 to 26 Vac or 28 to 32 Vdc

Electrical

connection

18 AWG [0.8 mm2] minimum

Inlet bushing

2 inlet bushings: 13/16” [20.6mm]

Control signal

Analog, Digital or Pulse with modulation (PWM) programmable (factory set with Analog control signal)

Angle of

rotation

0 to 90 degrees, mechanically adjustable (factory set with 90º stroke)

Direction of

rotation

Reversible, Clockwise (CW), or Counterclockwise (CCW) (factory set with CW direction)

Ambient

temperature

-22ºF to 122ºF [-30ºC to 50ºC]

Storage

temperature

-22ºF to 122ºF [-30ºC to 50ºC]

Relative

Humidity

5 to 95 % non condensing.

Weight

3 lbs. [1.4 kg]

Warning: Do not press the clutch when actuator is powered.

Dimensions

Dimension

Inches (in)

Metric (mm)

1.50

38.1

3.64

92.5

6.60

167.5

model 000 & 060

3.02

76.8

model 020 & 080

3.81

96.8

Enerdrive System U.S.A. Patent #5,278,454

Features:

Mounts easy on round & square shaft (with option –8)

External clutch for manual adjustments

Maintenance free

Position indicator

Control signal fully programmable

The fastest actuator of the world (model BM_ _ _FF)

Fail safe by Enerdrive System1(on model 060 & 080)

Auxiliary switches (on model 020 & 080)

BM000

BM020

BM060

BM080

BM000F

BM020F

BM060F

BM080F

BM000FF

BM020FF

BM060FF

BM080FF

BM Series Actuators

Specification and Installation Instructions

www.neptronic.com 2

Caution

We strongly recommend that all Neptronic®products be wired to a separate transformer and that transformer shall service only Neptronic®products. This precaution will

prevent interference with, and/or possible damage to incompatible equipment. When multiple actuators are wired on a single transformer, polarity must be observed. Long

wiring runs create voltage drop which may affect the actuator performance.

Mechanical Installation

1. Manually close the damper blades and position the

actuator at 0º or 90º.

2. Slide the actuator onto the shaft.

3. Tighten the nuts on the “U” bolt to the shaft with an 8mm

wrench to a torque of 60 in.lb. [6.7 Nm].

4. Slide the mounting bracket under the actuator. Ensure free

movement of the slot at the base of the actuator. The

bracket pin must be placed in the mid distance of the slot.

5. Fix the bracket to the ductwork with #8 self-tapping screws.

Wiring Diagrams

Analog

For 4 to 20mA control signal, connect supplied 500 Ohm resistor between

pins 1 and 3.

For 2 to 10Vdc feedback signal, connect supplied 500 Ohm resistor

between pins 1 and 5.

PWM

3-wire/Digital 2 positions

4-wire/Digital 3 point floating

Note: In Digital Mode, the actuator is sensitive to induced electrical voltages from external sources. To prevent interference, install a

2.2k Ohm, 0.5 W resistor (included) between pins 1 and 3 and another between pins 1 and 4 of TB1 as shown above.

Note: In any of the above wiring configurations, connect a supplied 500 Ohm resistor between pins 1 and 5 for a 2-10Vdc feedback

signal.

CLUTCH

MOUNTING

BRACKET

1 2 3 4

COMMON (-)

SUPPLY (+)

FEEDBACK

4 to 20 mA

2 to 10 Vdc

1 2 3 4

COMMON (-)

SUPPLY (+)

FEEDBACK

4 to 20 mA

PWM CONTROL SIGNAL

1 2 3 4

Common (-)

24Vac (+)

Feedback

4 to 20 mA

Drive CW

Drive CCW

2.2K

1 2 3 4

Common (-)

24Vac (+)

Feedback

4 to 20 mA

Drive CW

Drive CCW

2.2K

BM Series Actuators

Specification and Installation Instructions

www.neptronic.com 3

PC Board

DIP Switch Settings

NOTE*: To use DIP switch #3 in other modes

(analog/digital), refer to Feedback Selection (CCW

Direction) on page 4.

Stroke Adjustment –No control signal change

1. Apply power and, wait for at least 10 seconds.

2. Press and release the reset button to start the auto-stroke process.

The LED should be illuminated.

a. First option:

The actuator will then travel in both directions to find its limits and position itself according to the demand.

The LED will extinguish, the process is complete.

b. Second option:

When the desired end position is reached, press and release the reset button. The actuator goes to the start

position. You can also press and release the reset button when it reaches the start position. Once this process is

complete, the LED extinguishes.

Programming –Change of control signal

a. Remove power and put all dip switches to "OFF" (Default).

b. Apply power and, within 10 seconds, press and release the reset button. The LED should be blinking.

c. Select the control signal with DIP switches:

DIP Switch

Signal

Move DS #1 to ON and then OFF

Digital, On/Off or 3 point floating

Move DS #2 to ON and then OFF

PWM

Move DS #3 to ON and then OFF

Analog (default)

d. If PWM mode is selected; when programming is done

- If DIP switch #3 is ON, PWM uses 5-second pulse

- If DIP switch #3 is OFF, PWM uses 25-second pulse

Stroke adjustment

see the stroke adjustment section above.

BM060

1 2 3 4 5 Dip switch

Reset

button

LED

Terminal

1 2 3

Potentiometer

1 2 3

Rotation: CCW

Fail safe return at 90°

PWM mode: 5-sec pulse

Other modes: see note*

PWM mode: 25-sec pulse

Other modes: see note*

Rotation: CW

Fail safe return at 0°

OFF

BM Series Actuators

Specification and Installation Instructions

www.neptronic.com 4

Feedback selection (CCW direction)

To select the CCW direction, set DS #1 to ON, and if the actuator is in Analog or Digital mode, you can program the feedback signal

direction.

If switch No3 is "OFF":

The feedback control is automatically reverse to 4 to 20 mA for 90

to 0 degrees.

0º

20 mA 90º

4 mA

If switch No3 is "ON":

The feedback control is to 20 to 4 mA for 90 to 0 degrees.

0º

4 mA 90º

20 mA

Zero and span calibration

This feature is applicable to analog control signal only.

1. Remove power and put all dip switches "OFF". (factory preset).

2. Apply power and within 10 seconds press and hold the reset button until the LED flashes once. When the LED flashes,

release the reset button, the LED remains illuminated and the zero and span calibration process starts. NOTE: Do not hold

the reset button for too long as it may cancel the process.

3. Apply new minimum voltage.

It can be any value between 0 to 7 Vdc, with an external 0 to 10 volt supply (ex: MEP).

4. Press and release the reset button to memorize the new minimum voltage. The LED flashes once and then remains

illuminated.

5. Apply new maximum voltage.

It can be any value between 3 to 10 Vdc; this value should be greater than the new minimum value.

6. Press and release the reset button to memorize the new maximum voltage. The LED flashes once and then turns off.

The Zero and span calibration process is complete.

Note: The voltage difference between the minimum voltage and high voltage settings must be at least 3V. If not, the actuator

will ignore the values entered and use the previous values. For example, a minimum voltage of 5V and a maximum

voltage of 7V represent a difference of 2V.

Note: To reset zero and span to 2 to 10 Vdc (factory value), re-select the analog control signal mode, see Programming.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Neptronic Contrôleurs

Neptronic

Neptronic BBTHV1100A Manuel utilisateur

Neptronic

Neptronic BT100S Manuel utilisateur

Neptronic

Neptronic BM000N Manuel utilisateur

Neptronic

Neptronic TUCB Series Manuel utilisateur

Neptronic

Neptronic BBT24A Manuel utilisateur

Neptronic

Neptronic BT160 Manuel utilisateur

Neptronic

Neptronic EVCB Series Manuel utilisateur

Neptronic

Neptronic BBTS1000 Manuel utilisateur

Neptronic

Neptronic BT000S Manuel utilisateur

Neptronic

Neptronic BM200S Manuel utilisateur

Neptronic

Neptronic TSU00 Series Manuel utilisateur

Neptronic

Neptronic BT060X4 Manuel utilisateur

Neptronic

Neptronic HRO20 Manuel utilisateur

Neptronic

Neptronic ST000S Manuel utilisateur

Neptronic

Neptronic BT000 Manuel utilisateur

Neptronic

Neptronic TSUB00 Series Manuel utilisateur

Neptronic

Neptronic ARO24T Manuel utilisateur

Neptronic

Neptronic EVCB14NIT0S Manuel utilisateur

Neptronic

Neptronic HRO20LSS Manuel utilisateur

Neptronic

Neptronic TM200N Manuel utilisateur

Neptronic

Neptronic BM000S Manuel utilisateur

Neptronic

Neptronic AROB24T Manuel utilisateur

Neptronic

Neptronic TM200FN Manuel utilisateur

Neptronic

Neptronic DTS Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur