Neilsen CT5658 Manuel utilisateur
LOG SAW HORSE HOLDER FOLDING METAL
WITH PIVOTING CHAINSAW CLAMP
CT5658
ORIGINAL INSTRUCTIONS
Read all these instructions before assembling, operating or maintaining this product.
Cannon Tools Limited
Address:20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM
SAFETY RULES AND PRECAUTIONS
ATTENTION: Read and understand all warnings and safety instructions before
using this product. Failure to do so may result in electric shock, fire and/or
serious injury.
The following information on hazards and precautions includes the most
probable situations that may arise during the use of this machine.
Check all the documentation, packaging and product labels before using it. If you
encounter a situation not described in this manual use common sense to use the
machine as safely as possible and, if you see any danger, do not use the
machine.
Users
• This product is designed to be operated by adult users who have read and
understood these instructions. Do not allow minors and persons who do not
understand these instructions to use the product.
• Before using this product, familiarise yourself with the product. Make sure you
know where all the controls, safety devices are located and how to use them.
• If you are an inexperienced user, we recommend that you practice doing simple
jobs and, if possible, in the company of an experienced person.
Personal Security
• Be alert, watch what you are doing and use common sense when handling this
product.
• Inspect the product before use. Do not use this product if any of its components
are damaged.
• Do not stand on the workshop chair.
• Never exceed the maximum weight of 150 kg. Do not force the product and you
will work better and safer.
Work Area Safety
• This product is not a toy. It must be kept out of the reach of children.
• Keep children, animals and other people away while handling this product.
• Use this product on hard, flat surfaces capable of supporting the load.
• Be careful when near naked flames, the surface of the product may burn.
INSTRUCTIONS FOR SAFE USE OF THE LOG HORSE WITH CHAINSAW
HOLDER
1. Place the wood on the log table pushing the end to the measuring rod. Hold
the wood down firmly with your left hand,keeping your hand well clear of the
cutting edge of the chainsaw, and arc the chainsaw down to cut.
2. The log table on the Log Horse is designed for taking lengths to a maximum
of 1.80 meters and a maximum diameter of 20 cm. The maximum permissible
load on the Log Horse is 150 kg.
3. The Log Horse chain guard is designed for chainsaws with a cutting bar not
longer than 45 cm. A chainsaw with a cutting bar longer than 45 cm (which
protrudes beyond the chain guard) is not recommended.
4. The pivot clamp and guard must be detached when using the chainsaw
separately from the Log Horse.
5. The pivot clamp and support must be kept well lubricated.
6. The Log Horse must be used on flat surfaces only.
7. Ensure the nuts and bolts on the pivot clamp and guard are kept tight at all
times. When using a chainsaw with the Log Horse it is essential that all safety
codes and practices of the chainsaw manufacture and Health and Safety
Executive are fully followed.
ASSEMBLY OF THE LOG HORSE WITH CHAINSAW HOLDER
Fig 1. Pivot Clamp Support and
Measuring Rod -Insert the pivot clamp
support (adjustable vertically) into the
sawhorse table with the measuring
rod holder (adjustable horizontally)
using the bolt and washer supplied.
The vertical adjustment for the pivot
clamp support is to accommodate
different sized chain bars -the larger
and longer the bar, the higher the pivot
clamp should be placed.
Adjust so that the tip of the chain bar
extends beyond the table, so that it is
cutting completely through the log.
The measuring rod can be adjusted
horizontally to allow each log to be cut
to the desired length.
Fig 2. Pivot Clamp - Insert the male rod
on the pivot clamp into the female cylinder
on the pivot support clamp and secure
with the R clip.
Fig 3. Carefully lower the chainsaw bar
into position between the two solid blocks
in the pivot clamp and ensure a 2 cm gap
between the body of the chainsaw and the
clamp. Make sure that the bar is
approximately 90 degrees to the clamp and
well clear of the chain before tightening the
bolt. Once tightened, test the arc of travel
to make sure that the chain bar does not
touch any part of the sawbench.
Fig 4a. Position the chainsaw bar guard
around the top rod of the pivot clamp.
Securely tighten the bar guard with
bolt and nut provided.
Fig 4b. Slide the guard backwards and
Forwards as necessary to a position
in which the guard is well clear of the
chain.
Tighten the bolt.
Re-check for clearance.
The Log Horse is now ready for use.
ASSEMBLY PARTS DIAGRAM
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China
Table des matières
Autres manuels Neilsen Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
