Neilsen CT2283 Manuel utilisateur

1/2” DR AIR RATCHET CT2283

ORIGINAL INSTRUCTIONS

Cannon Tools Limited

Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

SAVE THESE INSTRUCTIONS AND PRECAUTIONS.

READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

EC DECLARATION OF CONFORMITY

We CANNON TOOLS LTD

20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.

Declare that the following machine complies with the appropriate basic safety

and health requirements of the EC Directive based on its design and type, as

brought into circulation by us.

In case of alteration of the machine, not agreed upon by us, this declaration will

lose its validity.

Product description: 1/2” DR AIR RATCHET

Model: CT2283

Applicable EC Directives:

EC Machinery Directive 2006/42/EC

Harmonized standards

EN ISO 11148-6:2012

20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Mr. Gurcharan Tony Singh Sanghera

Managing Director

CANNON TOOLS LTD

2021-03-18

1.SPECIFICATION

Model；CT2283

Max. air pressure: 6.2 bar (90 psi)

No load speed: 180/min

Air consumption: 5.4cfm

Max. torque: 75 ft-lb

Air inlet: 1/4"

2. SAFETY INSTRUCTIONS

•Follow all workshop safety rules, regulations, and conditions when using

wrench.

•Do not wear watches, rings, bracelets or loose clothing when using air tools.

•WARNING! Disconnect from air supply before changing accessories or

servicing.

•Maintain the wrench in good condition and replace any damaged or worn parts.

Use genuine parts only. Non-authorized parts may be dangerous.

•WARNING! Check correct air pressure is maintained and not exceeded. We

recommend 90psi.

•Keep air hose away from heat, oil and sharp edges. Check air hose for wear

before each use and ensure that all connections are secure.

•Only use sockets which are specifically designed for use with a ratchet wrench.

•Wear approved safety eye/face shield, ear defenders, and hand protection.

•WARNING! Due to the possible presence of asbestos dust from brake linings,

when working around vehicle brake systems we recommend you wear suitable

respiratory protection.

•Maintain correct balance and footing. Ensure the floor is not slippery and wear

non-slip shoes.

•Keep children and non essential persons away from the working area.

•DO NOT use the wrench for a task it is not designed to perform.

•DO NOT use wrench if damaged or thought to be faulty.

•DO NOT use wrench unless you have been instructed in its use by a qualified

person.

•DO NOT carry the wrench by the air hose.

•DO NOT direct air from the air hose at yourself or others.

•When not in use disconnect from air supply and store in a safe, dry, childproof

location.

3. TECHNICAL DESCRIPTION

1. Ratchet anvil 1/2”

2. Trigger

3. Reverse bottom

4. Air inlet

4. AIR SUPPLY

1. Ensure tool air valve (or trigger) is in “off ” position before connecting to the air

supply.

2. You will require an air pressure of 90psi, and an air flow according to

specification.

WARNING! Ensure the air supply is clean and does not exceed 90psi while

operating the tool. Too high an air pressure and unclean air will shorten the

product life due to excessive wear, and may be dangerous causing damage

and/or personal injury.

3. Drain the compressor’s air tank daily. Water in the air line will damage the

tool.

4. Clean the compressor’s air inlet filter weekly.

5. Line pressure should be increased to compensate for unusually long air

hoses (over 8 metres). The minimum hose diameter should be 1/4” I.D. and

fittings must have the same inside dimensions.

6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and

make certain that all connections are secure.

7. Vibration may cause failure if a quick change coupling is connected directly to

the tool.

8. To overcome this, connect a leader hose to the tool. A quick change coupling

may then be used to connect the leader hose to the air line recoil hose. See fig 1.

5. OPERATION

WARNING: Ensure you read, understand and apply safety

instructions before use.

General operation instructions

•Attach an air hose (not included) to the compressor’s air outlet. Connect

the air hose to the air inlet of the ratchet wrench.

•The air hose must be long enough to reach the work area with enough

extra length to allow free movement while working.

•Turn on the air compressor according to the manufacturer’s directions

and allow it to build up pressure until it cycles off.

•Push and snap socket (not included) onto the anvil.

•The wrench can be used in either forward or reverse direction by

adjusting the reverse switch.

•To tighten, place the socket over the nut you wish to tighten.

•Hold the handle firmly and place other hand on top of housing. Then gently

squeeze the trigger.

•If tool requires more force to accomplish task in forward or reverse setting,

verify that the tool receives sufficient, unobstructed airflow and increase the

pressure output of regulator up to maximum air pressure rating of tool.

CAUTION! Do not exceed tool’s maximum air pressure rating (6.3 bar).

•If tool still does not have sufficient force at maximum pressure and sufficient

airflow, then a larger tool may be required. When the nut is tightened or

loosened, release the trigger.

Loading and operation

•Only use sockets which are specifically designed for use with the wrench.

•Changing sockets

Disconnect the tool from the source o f compressed air.

Remove the socket you no longer wish to use from the anvil.

Subsequently fit the new socket to the square drive as described

above.

DO NOT use any additional force upon the wrench in order to

remove a nut.

DO NOT allow wrench to free run for an extended period of time

as this will shorten its life.

6. MAINTENANCE

WARNING: Disconnect wrench from air supply before changing accessories,

servicing or performing maintenance. Replace or repair damaged parts. Use

genuine parts only. Non-authorised parts may be dangerous.

1. Lubricate the air wrench daily with a few drops of air tool oil dripped into the

air inlet

2. DO NOT use worn or damaged sockets.

3. Loss of power or erratic action may be due to the following:

Excessive drain on the air line.

Moisture or restriction in the air pipe.

Incorrect size or type of hose connectors.

To remedy check the air supply and follow instructions.

4. Grit or gum deposits in the ratchet wrench may also reduce

performance. If your model has an air strainer (located in the area of

the air inlet), remove the strainer and clean it.

5. When not in use, disconnect from air supply, clean air ratchet wrench

and store in a safe, dry, childproof location.

7. DISPOSAL

At the end of the machine's working life, or when it can no longer be repaired,

ensure that it is disposed of according to national regulations.

Contact your local authority for details of collection schemes in your area.

In all circumstances:

Do not dispose of this tool with domestic waste.

Do not incinerate.

During decommissioning of the equipment, certain hazards should be

understood and avoided:

. Only with the line pressure released shall the equipment be

disassembled.

.Goggles should be worn.

8. SYMBOLS

In this manual and/or on the machine the following symbols are used:

Denotes risk of personal injury, loss of life or damage to the tool in

case of non-observance of the instructions in this manual.

Wear hearing protection.

Wear safety goggles.

Contact with or inhalation of dust coming free during use (e.g.

lead-painted surfaces, wood and metal) can endanger your health

and the health of bystanders. Always wear appropriate protective

equipment, such as a dust mask. Always use proper dust

extraction during use.

Wear gloves.

9. EXPLODED VIEW

Table des matières

Autres manuels Neilsen Outils électriques

Neilsen

Neilsen CT3995 Manuel utilisateur

Neilsen

Neilsen CT4789 Manuel utilisateur

Neilsen

Neilsen CT1282 Manuel utilisateur

Neilsen

Neilsen CT0674 Manuel utilisateur

Neilsen

Neilsen CT0870 Manuel utilisateur

Neilsen

Neilsen CT1764 Manuel utilisateur

Neilsen

Neilsen CT4040 Manuel utilisateur

Neilsen

Neilsen CT0675 Manuel utilisateur

Neilsen

Neilsen CT0904 Instructions de fonctionnement

Neilsen

Neilsen CT1109 Manuel utilisateur

Neilsen

Neilsen CT2594 Instructions de montage

Neilsen

Neilsen CT1703 Manuel utilisateur

Neilsen

Neilsen CT4542 Manuel utilisateur

Neilsen

Neilsen CT3772 Manuel utilisateur

Neilsen

Neilsen CT1091 Manuel utilisateur

Neilsen

Neilsen CT2914 Manuel utilisateur

Neilsen

Neilsen CT3994 Manuel utilisateur

Neilsen

Neilsen CT3990 Manuel utilisateur

Neilsen

Neilsen CT3950 Manuel utilisateur

Neilsen

Neilsen CT2818 Instructions de fonctionnement

Neilsen

Neilsen CT1082 Manuel utilisateur

Neilsen

Neilsen CT3766 Manuel utilisateur

Neilsen

Neilsen CT0878 Manuel utilisateur

Neilsen

Neilsen CT4343 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel