NEC ME403U Manuel utilisateur

[Notice] Replacing the Lamp and the Filter

When approximately 300 hours before the lamp reaches the end of its life, the LAMP indicator

in the cabinet will blink ORANGE and the LAMP WARNING icon will appear at the top right of

the projection screen.

Even though the lamp may still be working, replace the lamp to maintain the optimal projector

performance.

After replacing the lamp and the filter, be sure to clear the lamp usage hours and the filter

usage hours.

Please refer to “❹ Replacing the Lamp and the Filter” in the user’s manual included on the

supplied NEC Projector CD-ROM. (→ Page 85)

Lamp life of this projector

ECO mode Normal ECO 1 ECO 2 Boost

Lamp life (hours) *10,000 12,000 20,000 8,000

* This is not a warranty time. Repair or replacement parts may be required before the

lamp is replaced.

- Four modes of the ECO mode can be selected: [Normal], [ECO 1], [ECO 2] and [Boost]

modes.

- If you select ECO 1 or ECO 2 mode, the lamp life will be increased, while lowering

power consumption.

- If you select Boost mode, the picture becomes brighter than the Normal mode.

However, the power consumption will increase and the lamp life may also be

shortened.

CAUTION

• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely

hot. Turn the projector off and then disconnect the power cord. Allow at least one

hour for the lamp to cool before handling.

• When removing the lamp from a ceiling-mounted projector, make sure that no one is

under the projector. Glass fragments could fall if the lamp has been burned out.

NOTE:

• Use the specified lamp for safety and performance.

To order the replacement lamp, specify your lamp type, NP47LP.

The replacement lamp comes with filters.

• DO NOT REMOVE ANY SCREWS except one lamp cover screw and three lamp housing

screws. You could receive an electric shock.

• Do not break the glass on the lamp housing.

Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the

glass surface might cause an unwanted shadow and poor picture quality.

Continued on Reverse Side

• The LAMP indicator in the cabinet will blink RED and the LAMP WARNING MESSAGE

will appear when you continue to use the projector for another 300 hours after the LAMP

WARNING icon appeared.

Lamp replacement

In this case, the lamp reaches the end of its life.

If this happens, be sure to replace the lamp.

• If you continue to use the lamp after the lamp reaches the end of its life, the lamp bulb

may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them

as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp

replacement.

Indicator Message when replacing the lamp

Indicators Projector status Procedure

POWER STATUS LAMP

Status varies Off Orange

( Blink )

Lamp replacement grace

period.

The lamp is now in the

replacement grace period

(300 hours). Replace the

lamp to new one as soon as

possible.

Status varies Off Red

( Blink )

Lamp replacement time

exceeded.

The lamp has exceeded its

replacement time. Replace

the lamp immediately.

To customers

Please read this supplement carefully before replace the lamp of your projector and keep it

with the User’s Manual CD-ROM and the Important Information handy for future reference.

Indicators

Printed in China

Autres manuels pour ME403U

Autres manuels NEC Projecteur

NEC

NEC DLP CINEMA NC1600C Manuel d'utilisation

NEC

NEC NP400 Series Manuel utilisateur

NEC

NEC M332XS Manuel utilisateur

NEC

NEC V311X Manuel utilisateur

NEC

NEC Showcase Series HT1100 Manuel utilisateur

NEC

NEC NP405 Manuel utilisateur

NEC

NEC MultiSync LT 80 Guide d'installation et d'utilisation

NEC

NEC M363XG Manuel utilisateur

NEC

NEC NP4001-07ZL Manuel utilisateur

NEC

NEC NP-PE401H Manuel utilisateur

NEC

NEC GT1150 Series Guide d'installation et d'utilisation

NEC

NEC NP905 Series Manuel utilisateur

NEC

NEC NP200 Manuel utilisateur

NEC

NEC NP-V311W Manuel utilisateur

NEC

NEC MM2000B Manuel utilisateur

NEC

NEC MultiSync MT1055 Guide d'installation et d'utilisation

NEC

NEC NP41 - TECHNISCHE DATEN Manuel utilisateur

NEC

NEC LT25 Series Manuel utilisateur

NEC

NEC NP4000 Manuel utilisateur

NEC

NEC VT595 Series Manuel utilisateur

NEC

NEC LT157 - XGA LCD Projector Guide d'installation et d'utilisation

NEC

NEC WT600 Series Guide de référence rapide

NEC

NEC MultiSync LT140 Guide d'installation et d'utilisation

NEC

NEC PA1004UL-W Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur